User`s guide

Index
Index-1
Numerics
2-port error corrections,
performing
, 6-42, 6-71
4 Param Displays softkey
, 1-18
A
aborting a print or plot process
,
4-31
absolute
ripple test value
, 1-92, 1-93
absolute power
, 6-39
accuracy
, 1-59
accuracy and input power
, 7-89
accuracy enhancement
, 7-8, 7-39,
7-53
accurate measurements of
electrically long devices
cause of measurement
problems
, 5-7
improving measurement
results
, 5-7
activating
averaging
, 5-15
chop sweep mode
, 5-12
display markers
, 1-25
fixed markers
, 1-29
limit test
, 1-82
activating the bandwidth test
,
1-97
active channel display
, 1-11
adapter removal
, 6-41
adapter removal calibration
(ECal)
, 6-69–??
adapters
minimizing error
, 6-47
adapters, matched
, 6-45
ADC
, 7-7
address menu
, 7-80
addressing two sources
, 2-29
adjusting
display colors
, 1-22
relative velocity factor
, 3-12
AmiPro, using
, 4-21
amplifiers, measuring
, 1-54
amplitude tracking
, 2-38
amplitude, tracking
, 1-42
analog in menu
, 7-23
analyzer display formats
, 7-25
group delay format
, 7-27
group delay principles
, 7-32
imaginary format
, 7-32
linear magnitude format
, 7-30
log magnitude format
, 7-25
phase format
, 7-26
polar format
, 7-29
real format
, 7-31
smith chart format
, 7-28
SWR format
, 7-31
analyzer internal memory, what
you can save
, 4-34
applying power
, 8-5
arrays
format
, 7-9
pre-raw data
, 7-8
raw
, 7-8
ASCII data formats
, 4-39
CITIfile
, 4-39
S2P data format
, 4-40
assigning standards to various
TRL classes
, 6-51
assigning standards to various
TRM classes
, 6-55
attenuator
, 7-14
attenuator, repetitive switching
,
7-14
attenuator, source step
, 7-4
auto sweep time mode
, 7-12
auto sweep time mode, setting
,
5-11
auto-feed, selecting
, 4-13
automatic mode
, 7-10
autostarting sequences
, 1-109
averaging
, 7-36
isolation
, 6-60
averaging factor, reducing
, 5-11
averaging, activating
, 5-15
averaging, sweep to sweep
, 7-7
B
band
adding a frequency
, 1-89
changing a frequency
, 1-88
deleting a frequency
, 1-90
frequency
, 1-87
bandwidth
, 1-97
bandwidth markers
displaying
, 1-98
bandwidth test
activating
, 1-97
running
, 1-97–1-100
setting up limits
, 1-95–1-97
bandwidth testing
, 1-95–1-100
bandwidth value
displaying
, 1-99
bandwidth, searching for
, 1-42
basic measurements, making
, 1-4
bilateral device
, 6-22, 6-25
blanking the display
, 1-21
block, receiver
, 7-4
built-in synthesized source
, 7-4
source step attenuator
, 7-4
built-in test set
, 7-4
C
cables, interconnecting
, 5-4
calculating statistics of
measurement data
, 1-43
calculations, ratio
, 7-7
calibrating for non-coaxial
devices
, 6-50
TRL error-correction
, 6-50
TRM error correction
, 6-54
calibrating for noninsertable
devices
, 6-40
adapter removal
, 6-41, 6-69
matched adapters
, 6-45
modifying the cal kit through
definition
, 6-46
calibrating the analyzer receiver
to measure absolute power
,
6-39
calibration
ECal
, 6-58–6-68
electronic. See ECal
power meter
, 2-12
calibration considerations
, 6-4
calibration standards
, 6-5
clarifying type-N connector sex
,
6-4
device measurements
, 6-4
error-correction stimulus state
,
6-9
frequency response of
calibration standards
, 6-6
interpolated error correction
,
6-8
measurement parameters
, 6-4
omitting isolation calibration
,
6-4
restarting a calibration
, 6-5
saving calibration data
, 6-5
calibration data, saving
, 6-5, 7-66
calibration kit menu
, 7-59
defining standard menus
, 7-60
label class menu
, 7-66
label kit menu
, 7-66
label standard menu
, 7-63
specify class menu
, 7-63
specifying offset menu
, 7-62
calibration kit, saving a modified
,
7-66
calibration kits, modifying
, 7-58
calibration routines
, 7-56
full two-port calibration
, 7-57
response and isolation
calibration
, 7-56
response calibration
, 7-56
S11 and S22 one-port
calibration
, 7-57