User`s guide

Index
Index-5
high dynamic range swept RF/IF
conversion loss
measurement parameters for IF
range
, 2-20
power meter calibration over IF
range
, 2-20
power meter calibration over RF
range
, 2-23
receiver calibration over IF
range
, 2-22
RF frequency range
, 2-22
high power
configuration one
, 1-67
configuration three
, 1-70
configuration two
, 1-69
measurements
, 1-66
horizontal axis
, 3-13, 3-14, 3-16,
3-20, 3-23
how RF and IF are defined
, 2-7
HPGL
compatible printer
, 4-19
initialization sequence, sending
to the printer
, 4-24
initialization sequence, storing
,
4-23
HPGL compatible printer
, 4-23
HPGL/2 compatible printer
, 4-9
I
IF bandwidth reduction
, 7-37
IF bandwidth, setting segment
,
7-19
IF delay, detecting
, 5-10
IF detection
, 7-7
IF range
measurement parameters
, 2-20
power meter calibration
, 2-20
receiver calibration
, 2-22
IF, defining
, 2-7
imaginary format
, 7-32
improving measurement results
,
5-7
decreasing the sweep rate
, 5-8
decreasing time delay
, 5-8
improving raw source match and
load match for TRL*/LRM*
calibration
, 7-72
increase sweep speed
using fast 2-port calibration
,
5-12
increasing dynamic range
, 5-14
increasing test port input power
,
5-14
reducing receiver crosstalk
, 5-14
reducing the receiver noise floor
,
5-14
increasing measurement
accuracy
, 5-4
connector repeatability
, 5-4
frequency drift
, 5-5
interconnecting cables
, 5-4
performance verification
, 5-5
reference plane and port
extensions
, 5-5
temperature drift
, 5-5
increasing sweep speed
, 5-9
activating chop sweep mode
,
5-12
decreasing the frequency span
,
5-10
reducing the averaging factor
,
5-11
reducing the number of
measurement points
, 5-11
setting the auto sweep time
mode
, 5-11
setting the sweep type
, 5-11
using external calibration
, 5-12
using swept list mode
, 5-9
viewing a single measurement
channel
, 5-12
widening the system bandwidth
,
5-11
increasing test port input power
,
5-14
incrementing the source
frequencies
, 2-31
in-depth sequencing information
,
1-108
autostarting sequences
, 1-109
commands completed before
next sequence begins
, 1-108
commands that require a clean
sweep
, 1-108
decision making functions
,
1-114
embedding loop counter value in
title
, 1-109
features that operate differently
in a sequence
, 1-108
forward stepping in edit mode
,
1-108
gosub sequence command
, 1-109
GPIO mode
, 1-110
limit test decision making
,
1-114
loop counter decision making
,
1-115
sequence decision making
menu
, 1-114
sequence size
, 1-109
sequence that jumps to itself
,
1-114
sequencing special functions
menu
, 1-114
titles
, 1-108
TTL I/O menu
, 1-110
TTL input decision making
,
1-111, 1-114
TTL out menu
, 1-114
TTL output for controlling
peripherals
, 1-110
indicators, GPIB STATUS
, 7-80
initializing loop counter value to
26
, 2-29
input ports menu
, 7-24
input power
, 1-59
inserting a command
, 1-104
insertion phase response
, 1-7, 1-8
instrument markings
, 8-4
instrument modes
, 7-84
external source mode
, 7-84
frequency offset operation
, 7-87
harmonic operation
, 7-88
network analyzer mode
, 7-84
tuned receiver mode
, 7-86
instrument state
file, deleting
, 4-49
files
, 4-44
re-saving
, 4-49
saving
, 4-36, 7-66
saving and recalling
, 4-34
interconnecting cables
, 5-4
internal memory
, 4-34
internal R channel inputs
, 2-10
interpolated error correction
, 6-8
interpolation in power meter
calibration
, 6-34
interpreting
bandpass reflection response
horizontal axis
, 3-13
bandpass reflection response
vertical axis
, 3-13
bandpass transmission response
horizontal axis
, 3-14
bandpass transmission response
vertical axis
, 3-14
forward transform horizontal
axis
, 3-23
forward transform vertical axis
,
3-22
low pass response horizontal
axis
, 3-16
low pass response vertical axis
,
3-17
low pass step transmission
response horizontal axis
,
3-20
low pass step transmission
response vertical axis
, 3-20