User`s guide

Index
Index-7
how RF and IF are defined, 2-7
internal and external R channel
inputs
, 2-10
LO frequency accuracy and
stability
, 2-10
minimizing source and load
mismatches
, 2-4
power meter calibration
, 2-12
reducing the effect of spurious
responses
, 2-5
measurement data
, 1-20
dividing by the memory trace
,
1-20
viewing
, 1-20
measurement data trace
, 1-20
subtracting memory trace
, 1-20
measurement error
crosstalk
, 7-42
frequency response
, 7-42
isolation
, 7-42
load match
, 7-41
measurement errors
directivity
, 7-40
source match
, 7-41
measurement parameters
, 1-72,
6-4
center frequency, setting
, 1-36
choosing
, 1-4
display reference value, setting
,
1-38
electrical delay, setting
, 1-39
for IF range
, 2-20
frequency span, setting
, 1-37
lower stopband parameters
,
1-73
markers, setting with
, 1-35
passband parameters
, 1-73
start frequency, setting
, 1-35
stop frequency, setting
, 1-36
upper stopband parameters
,
1-73
measurements
basic
, 1-4
high power
, 1-66
phase or group delay
, 2-34
measuring
device under test
, 1-5
gain and reverse isolation
simultaneously
, 1-64
insertion phase response
, 1-7,
1-8
separate transmission paths
through the test device
using low pass impulse
mode
, 3-20
small signal transient response
using low pass step
, 3-19
measuring amplifiers
, 1-54
harmonics, measuring
, 1-55
high power measurements
, 1-66
measuring gain and reverse
isolation simultaneously
,
1-64
measuring gain compression
,
1-60
measuring electrical length
, 1-44
measuring gain compression
, 1-60
linear sweep
, 1-62
using linear sweep
, 1-62
measuring harmonics
additional harmonic
measurements
, 1-57
harmonic operation,
understanding
, 1-58
measuring magnitude
, 1-7
magnitude response
, 1-7
measuring phase distortion
, 1-44,
1-46
deviation from linear phase
,
1-47
group delay
, 1-47
memory math functions
, 1-19
memory trace
, 1-19, 1-20
viewing
, 1-20
memory, display
, 7-9
menu
address
, 7-80
analog in
, 7-23
calibration kit
, 7-59
conversion
, 7-23
edit limits
, 7-83
edit segment
, 7-83
input ports menu
, 7-24
offset limits
, 7-83
segment
, 7-17
S-parameter
, 7-23
stepped edit list
, 7-17
stepped edit subsweep
, 7-17
swept edit list
, 7-18
swept edit subsweep
, 7-18
microprocessor
, 7-5
microwave connector care
, 5-3
microwave systematic errors,
characterizing
, 7-43
minimizing
error when using adapters
, 6-47
source and load mismatches
, 2-4
minimum allowable stop
frequencies
, 3-16
minimum amplitude, searching
for
, 1-40
minimum bandwidth
, 1-97
minimum sweep time
, 7-12
mixer
fixed IF measurements
, 2-26
measurement
, 2-3
measurement diagram, using
,
2-17, 2-23
mixing signals, eliminating
unwanted
, 2-6
mode
auto sweep time
, 5-11, 7-12
chop sweep
, 5-12
continuous correction
, 6-38
copy
, 7-81
external source
, 7-84
frequency offset
, 2-39
GPIO
, 7-81
low pass impulse
, 3-20
manual sweep time
, 7-12
network analyzer
, 7-84
pass control
, 7-80
system controller
, 7-80
talker/listener
, 7-80
time domain bandpass
, 3-12
time domain low pass
, 3-15
tuned receiver
, 7-86
model
one-port error
, 7-43
two-port error
, 7-48
modified colors
, 1-23
recalling
, 1-23
saving
, 1-23
modify colors menu
, 1-22
modifying
cal kit through definition
, 6-46
command
, 1-104
standard definitions
, 6-50
modifying calibration kits
, 7-58
calibration kit menu
, 7-59
saving to a disk
, 7-66
verifying performance
, 7-66
module information
, 6-64
multiple
measurement configuration,
single connection
, 1-122
measurements per page,
plotting from a disk
, 4-26
measurements, plotting on a full
page
, 4-27
plots, outputting to a single page
using a plotter
, 4-25
N
N dB Point
, 1-97
names for CSV files
, 4-43
naming files generated by a
sequence
, 1-106
network analyzer mode
, 7-84
noise floor plot
, 5-17
noise reduction techniques
, 7-36