User`s guide

Index
Index-9
loss of power meter calibration
data
, 6-33
using continuous correction
mode
, 6-38
using sample-and-sweep
correction mode
, 6-36
power ranges
, 7-10
automatic mode
, 7-10
manual mode
, 7-10
power sensor calibration data,
entering
, 6-34
power sweep
, 7-20
power, output
, 7-10
primary measurement channels,
viewing
, 1-12
principles, group delay
, 7-32
print
aborting a process
, 4-31
print function
configuring
, 4-4
defining
, 4-6
printer
color printer, using
, 4-6
HPGL compatible printer
, 4-19,
4-23
HPGL/2 compatible printer
, 4-9
printing
measurement results
, 4-3
multiple measurements per
page
, 4-8
one measurement per page
, 4-7
parameters, resetting to default
values
, 4-7
sequence
, 1-107
solving problems
, 4-33
printing or plotting the list values
or operating parameters
, 4-32
entire list of values
, 4-32
single page of values
, 4-32
procedure, TRL calibration
, 7-73
procedures for error correcting
measurements
, 6-10
types of error correction
, 6-10
processing details
, 7-7
accuracy enhancement
, 7-8
ADC
, 7-7
conversion
, 7-8
display memory
, 7-9
electrical delay block
, 7-8
format
, 7-9
format arrays
, 7-9
gating
, 7-8
IF detection
, 7-7
pre-raw data arrays
, 7-8
ratio calculations
, 7-7
raw arrays
, 7-8
sampler/IF correction
, 7-7
scale and offset
, 7-9
smoothing
, 7-9
sweep-to-sweep averaging
, 7-7
trace math operation
, 7-8
transform
, 7-9
vector error-correction
, 7-8
processing, data
, 7-6
prompting user to connect mixer
test setup
, 2-28
purging a sequence from a disk
,
1-107
R
R channel inputs, internal and
external
, 2-10
range
, 3-30
forward transform
, 3-24
frequency
, 1-59
resolution
, 3-34
ratio calculations
, 7-7
ratio measurements in channel 1
and 2, to
, 1-20
raw arrays
, 7-8
raw source match
, 7-72
real format
, 7-31
recall time, reducing
, 5-18
recalling a file
, 4-50
solving problems
, 4-51
recalling instrument states
, 4-34
receiver
calibration
, 6-15
crosstalk, reducing
, 5-14, 5-18
noise floor, reducing
, 5-14
receiver block
, 7-4
reducing
averaging factor
, 5-11
effect of spurious responses
, 2-5
number of measurement points
,
5-11
reducing recall time
, 5-18
understanding spur avoidance
,
5-18
reducing trace noise
, 5-15
activating averaging
, 5-15
changing system bandwidth
,
5-15
reduction, IF bandwidth
, 7-37
reference plane and port
extensions
, 5-5
reflection measurements
response and isolation error
correction
, 6-19
response error correction
, 6-12
reflection measurements in time
domain low pass
, 3-16
interpreting the low pass
response horizontal axis
,
3-16
interpreting the low pass
response vertical axis
, 3-17
reflection measurements using
bandpass
interpreting the band pass
reflection response vertical
axis
, 3-13
reflection measurements using
bandpass mode
, 3-12
interpreting the bandpass
reflection response
horizontal axis
, 3-13
reflection response
measurements, making
, 3-9
relative velocity factor, adjusting
,
3-12
removing adapter delay
, 6-42
removing the effect of an adapter
,
6-74
renaming a file
, 4-50
repeatability, connector
, 5-4
repetitive switching of the
attenuator
, 7-14
required peripheral equipment
,
7-5
required test equipment,
connecting
, 1-4
requirements for TRL standards
,
7-73
re-saving an instrument state
,
4-49
resetting
plotting parameters to default
values
, 4-16
printing parameters to default
values
, 4-7
resolution
, 3-32
range resolution
, 3-34
response resolution
, 3-32
response
calibration
, 2-28
error correction for reflection
measurements
, 6-12
error correction for transmission
measurements
, 6-14
magnitude
, 1-7
resolution
, 3-32
response and isolation
calibration
, 7-56
response and isolation error
correction for reflection
measurements
, 6-19
response calibration
, 7-56
restarting a calibration
, 6-5