User's Manual

60
Table 5-3. Replaceable Parts List (continued)
Ref. Desig. Agilent Model Agilent Part Number Description
C34 All 0160-6805
fxd met 0.01
µF 400V
CB1 6010A 6012B, 6015A See Chassis Electrical
CR1 All 1901-0731 power rect. 400V
CR2 All 1901-0731 power rect. 400V 1A
CR3,4 All 1901-0050 diode-switching 80V 200ma
CR5 All 1901-0731 Power rect. 400V
CR6-13 All 1901-0731 Power rect. 400V
DS1 All 1990-0517 LED visible
F1 All 2110-0001 fuse 1A 250V
F2 All 2110-0671 fuse .125A 125V
K1,2 All 0490-1834 Relay
L1 All 06012-80003 Snubber wire
9170-0707 ferrite core, (ref. L1)
L2 6010A, 6012B, 6015A 9170-1267 Magnetic core
5080-2040 jumper for L2
L3 6010A 9140-1064 Output Choke
L3 6012B 06012-80095 Output Choke
9170-0721 ferrite core, (ref. L1)
L2,3 6011A 06011-80092 Output Choke
L3 6015A 5080-2131
Ind fxd 18
µH 5A
L4 6010A, 6012B, 6015A See Chassis Electrical
L4 6011A 9170-1267 Magnetic core
5080-2040 jumper for L2
Q1 6010A 1855-0456 MOSFET N-Chan
Q1 6015A 1855-0777 Trans FET N-Ch 600V 3.2A
Q2 All 1855-0665 FET N-Chan
R1-4 All 0811-1866 fxd ww 10K 1% 5W
R5 All 0757-0418 fxd comp 619 1% 1/8W
R7 All 0698-5525 fxd comp 6.8 5% 1/2W
R8 All 0757-0765 fxd comp 36.5K 1% 1/8W
R9 All 0811-3700 fxd ww 20 10% 20W
R10 All 0811-3699 fxd ww 6 10% 20W
R11 6010A, 6015A 5080-2079 current sensing resistor
R11 6012B 06032-80001 current sensing resistor
R11,12 6011A NOT USED
R12,13 6010A, 6012B 0699-0188 fxd film 2.2 5% 1/4W
R12,13 6015A 0698-3492 fxd film 26.1 5% 1/4W
R13 6011A 06011-80001 Current Sensing Resistor
R14,15 6010A, 6015A NOT USED
R14,15 6011A 7175-0057 solid tinned copper wire
R14,15 6012B 0812-0100 fxd ww 2K 5% 5W
R16,17 All 0683-1065 fxd comp 10M 5% 1/2W
R18 All 0757-0921 fxd film 750 1% 1/8W
R19 All 0757-0403 fxd film 121 l% 1/8W
R20-23 6010A, 6012B, 6015A NOT USED
R20,23 6011A 0699-0208 fxd film 1 5% 1/4W
R24 All 0686-2015 fxd comp 200 5% 1/2W
R25-R28 6010A, 6015A NOT USED
R25 6011A, 6012B 0811-1869 fxd ww 30 ohms 3W
* Part of output filter (6010A, 5060-3520; 6011A, 5060-3525; 6012B, 5060-3523; 6015A, 5060-3521) which is mounted
on the output bus bars.