User`s manual

24
dataTec ▪ Ferdinand-Lassalle-Str. 52 ▪ 72770 Reutlingen ▪ Tel. 07121 / 51 50 50 ▪ Fax 07121 / 51 50 10 ▪ [e-mail] ▪ www.datatec.de
24
4000 X-Series specification overview
4022A 4024A 4032A 4034A 4052A 4054A 4104A 4154A
Bandwidth * (-3dB) 200 MHz 350 MHz 500 MHz 1 GHz 1.5 GHz***
4 channel real time bandwidth 200 MHz 350 MHz 500 MHz 1 GHz 1 GHz
Calculated rise time (10-90%) ≤ 1.75 ns ≤ 1 ns ≤ 700 ps ≤ 450 ps ≤ 300 ps
Input channels
DSOX 2 4 2 4 2 4 4 4
MSOX 2 + 16 4 + 16 2 + 16 4 + 16 2 + 16 4 + 16 4 + 16 4 + 16
Maximum sample rate 5 GSa/s half channel, 2.5 GSa/s all channel
Maximum memory depth Standard 4 Mpts, standard segmented memory
Display size and type 12.1-inch high-definition capacitive touch display
Waveform update rate > 1 million waveforms per second
System bandwidth with N2894A
standard passive probe
200 MHz 200 MHz 350 MHz 350 MHz 500 MHz 500 MHz 700 MHz 700 MHz
Oscilloscope Experience Redefined:
DSO and MSO 4000 X-Series oscilloscope
s
Vertical system analog channels
Hardware bandwidth limits Approximately 20 MHz (selectable)
Input coupling AC, DC
Input impedance Selectable: 1 MΩ ± 1% (16 pF), 50 Ω ± 1.5%
Input sensitivity range
200 MHz ~ 500 MHz models: 1 mV/div to 5 V/div** (1 MΩ and 50 ohm)
1 GHz and 1.5 GHz models: 1 mV/div to 5 V/div** (1 MΩ), 1 mV/div to
1 V/div (50 ohm)
Vertical resolution 8 bits
Maximum input voltage 300 Vrms, 400 Vpk; transient overvoltage 1.6 kVpk
With N2862A, N2863A or N2890A 10:1 probe: 300 Vrms
Frequency de-rating (assumes sine wave input): 400 Vpk until 40 kHz. Then
de-rates at 20 db/dec until 6 Vpk
DC vertical gain accuracy* ± 2.0% full scale**
DC vertical offset accuracy ± 0.1div ± 2 mV ± 1% of offset setting
Channel-to-channel isolation
200 MHz~1 GHz ≥ 40 dB from DC to maximum specified bandwidth of each model
1.5 GHz ≥ 40 dB from DC to 1 GHz, ≥ 35 dB from 1 GHz to 1.5 GHz
Offset range ±5 V (< 10 mV/div), ±20 V (10 to 200 mV/div), ±75 V (> 200 mV/div)
Vertical system digital channels
Digital input channels 16 digital (D0 to D15. Pod 1: D7 ~ D0, Pod 2: D15 ~ D8)
Thresholds Threshold per pod
Threshold selections TTL (+1.4 V), 5 V CMOS (+2.5 V), ECL (–1.3 V), user-defined (selectable by pod)
User-defined threshold range ± 8.0 V in 10 mV steps
Maximum input voltage ± 40 V peak CAT I; transient overvoltage 800 Vpk
Threshold accuracy* ± (100 mV + 3% of threshold setting)
Maximum input dynamic range ± 10 V about threshold
Minimum voltage swing 500 mVpp
Input impedance 100 kΩ ± 2% at probe tip
Input capacitance ~8 pF
Vertical resolution 1 bit
InfiniiVision 4000 X-Series Performance Characteristics
* Denotes warranted specifications, all others are typical. Specifications are valid after a 30-minute warm-up period and ± 10 °C from firmware calibration temperature.
** 1 mV/div and 2 mV/div is a magnification of 4 mV/div setting. For vertical accuracy calculations, use full scale of 32 mV for 1 mV/div and 2 mV/div sensitivity setting.
*** 1.5 GHz real time bandwidth in half-channel mode or full channel equivalent time mode.