User`s guide

SCPI Commands Appendix C
Model N6705A User’s Guide 137
SCPI Command Description
[SOURce:]ARB continued
:STEP
:END[:LEVel] < NRf+>, (@channel) Sets the end voltage of the step
:STARt
[:LEVel] < NRf+>, (@channel) Sets the initial voltage of the step
:TIMe < NRf+>, (@channel) Sets the length of the start time or delay
:TRAPezoid
:END:TIMe < NRf+>, (@channel) Sets the length of the end time
:FTIMe < NRf+>, (@channel) Sets the length of the fall time
:RTIMe < NRf+>, (@channel) Sets the length of the rise time
:STARt
[:LEVel] < NRf+>, (@channel) Sets the initial voltage of the trapezoid
:TIMe < NRf+>, (@channel) Sets the length of the start time or delay
:TOP
[:LEVel] < NRf+>, (@channel) Sets the top level voltage of the trapezoid
:TIMe < NRf+>, (@channel) Sets the length of the top of the trapezoid
:UDEFined
:BOSTep[:DATA] <Bool> {,<Bool>}, (@chanlist) Generate triggers at the Beginning Of Step
:POINts? (@chanlist) Returns the number of BOST points
:DWELl <NRf> {,<NRf>}, (@chanlist) Sets the user-defined dwell values
:POINts? (@chanlist) Returns the number of dwell points
:LEVel <NRf> {,<NRf>}, (@chanlist) Sets the user-defined voltage values
:POINts? (@chanlist) Returns the number of voltage points
CURRent
[:LEVel]
[:IMMediate][:AMPLitude] <NRf+>, (@chanlist) Sets the output current
:TRIGgered [:AMPLitude] <NRf+>, (@chanlist) Sets the triggered output current
:MODE FIXed | STEP | LIST | ARB, (@chanlist) Sets the current trigger mode
:PROTection
:DELay[:TIME]<NRf+> (@chanlist) Sets the over-current protection programming delay
:STARt SCHange | CCTRans, (@chanlist) Sets the over-current protection programming mode
:STATe <Bool>, (@chanlist) Enables/disables over-current protection on the selected output
:RANGe <NRf+>, (@chanlist) Sets the output current range (only on N6761A/62A)
DIGital
:INPut:DATA? Reads the state of the digital port pins
:OUTPut:DATA <NRf> Sets the digital port
:PIN<1-7>
:FUNCtion DIO | DINPut | TOUTput | TINPut |
FAULt
1
| INHibit
2
| ONCouple | OFFCouple
Sets the selected pin’s function (
1
PIN1 only;
2
PIN3 only)
:POLarity POSitive | NEGative Sets the selected pin’s polarity
LIST (LIST commands only on N6761A/62A and Opt. 054)
:COUNt <NRf+> | INFinity, (@chanlist) Sets the list repeat count
:CURRent [:LEVel] <NRf> {,<NRf>}, (@chanlist) Sets the current list
:POINts? (@chanlist) Returns the number of current list points
:DWELl <NRf> {,<NRf>}, (@chanlist) Sets the list of dwell times
:POINts? (@chanlist) Returns the number of dwell list points
:STEP ONCE | AUTO, (@chanlist) Specifies how the list responds to triggers
:TERMinate:LAST <Bool>, (@chanlist) Sets the list termination mode
:TOUTput
:BOSTep[:DATA] <Bool> {,<Bool>}, (@chanlist) Generate triggers at the Beginning Of STep
:POINts? (@chanlist) Returns the number of BOST list points
:EOSTep[:DATA] <Bool> {,<Bool>}, (@chanlist) Generate triggers at the End Of STep
:POINts? (@chanlist) Returns the number of EOST list points