Specifications

22
Test set options
One of the following test set options must be selected.
□ Standard configuration (Option 700)
The standard configuration is the basic test set configuration,
which does not include signal conditioning devices such as
amplifiers.
□ Add amplifiers for improved dynamic range (Option 001)
Option 001 adds an amplifier between each test port coupler
and the receiver switch to improved system dynamic range. It
is primarily offered for the test set with solid-state switches to
compensate for the insertion loss.
□ Add amplifiers and bias-tees (Option 002)
Option 002 adds an amplifier between each test port coupler
and the receiver switch to improved system dynamic range and
bias-tees for all test ports on the test set as well as the ana-
lyzer. It is primarily offered for the test set with solid-state
switches to compensate for the insertion loss.
Interface kits
The interface kit includes a set of semi-rigid RF jumper cables
and two pairs of rear locking feet that connect and lock the ana-
lyzer and the test set together. When ordering a multiport test
set, the analyzer that is used with the test set must be specified
to add one of the following interface kits. The availability depends
on the test set model. There are following three interface kit
models based on the jumper connector layouts on the test set.
Therefore, only one interface kit model (“PX”, “PN”, or “PL”) is
available on each test set. Each interface kit model has one digit
suffix indicating the connector type; 1 for 1.85 mm, 2 for 2.4 mm
and 3 for 3.5 mm (or SMA).
□ U3021PXx Interface kit for test set with jumper connectors
to align with N524xA PNA-X and N522xA PNA
□ U3021PNx Interface kit for test set with jumper connectors
to align with E836xB/C PNA and N5230A/C-x25
2-port PNA-L
□ Option 261 For use with E8361A/C 2-port PNA
□ Option 262 For use with E8362B/C 2-port PNA or N5230A/C-225
2-port PNA-L
□ Option 263 For use with E8363B/3C/4B/4C 2-port PNA or
N5230A/C-425/525 2-port PNA-L
□ Option 430 For use with N5230A/C-245/246 4-port PNA-L
□ Option 242 For use with N5241A/2A-2xx 2-port PNA-X or
N5221A/2A-2xx 2-port PNA
□ Option 442 For use with N5241A/2A-400 4-port PNA-X or
N5221A/2A-4xx 4-port PNA
□ Option 245 For use with N5244A/5A-200 2-port PNA-X or
N5224A/5A-2xx 2-port PNA
□ Option 445 For use with N5244A/5A-400 4-port PNA-X or
N5224A/5A-4xx 4-port PNA
□ Option 247 For use with N5247A-200 2-port PNA-X or
N5227A-2xx 2-port PNA
□ Option 447 For use with N5247A-400 4-port PNA-X or
N5227A-4xx 4-port PNA
When ordering an additional cable set, a spare cable or rear
locking feet, refer to the multiport test set user’s guide or go to:
www.agilent.com/find/multiport
Millimeter-wave measurements
□ Single sweep solution to 110 GHz
The 67 GHz PNA and PNA-X network analyzers allow extend-
ing the maximum frequency to 110 GHz with a 1.0 mm coaxial
connector, enabling 10 MHz to 110 GHz single sweep mea-
surements using a millimeter-wave controller and frequency
extenders with built-in combiner.
The 10 MHz to 110 GHz broadband millimeter-wave system
provides high performance and capabilities including power
control, 4-port true-differential, and frequency converter
measurements. It is configured with an N5227A PNA with
Option 201 (2-ports) or Option 401 (4-ports), or N5247A with
Option 200 (2-ports) or Option 400 (4-ports), Option 020 IF
access, an N5261A 2-port or an N5262A 4-port millimeter-wave
test set controller with 1.85 mm coaxial cables (Option 112 for
N5261A, Option 114 for N5262A) and RF/LO/IF/DC cables sets
(to select the cable length and quantities), and one (for 2-ports)
or two (for 4-ports) each of right and left frequency extenders
with required attenuators and bias-tee configurations.
□ Waveguide banded solutions to 1.05 THz
The waveguide banded millimeter-wave solution covers wave-
guide bands from 50 GHz to 1.05 THz. A 2- or 4-port PNA or
PNA-X in conjunction with N5261A (for 2-port) or N5262A
(for 4-port) configures for the most complete millimeter wave
solution. It is configured with a PNA Series with Option 020 IF
access, configurable test set (Option 201 or 401), and fre-
quency offset mode (Option 080), or PNA-X Series with 2-port
(Option 200) or 4-port (Option 400) and IF access (Option 020).
For the millimeter-wave test controller, appropriate RF cable
option and RF/LO/IF/DC cable set option for frequency
extenders must be selected for the analyzer’s connector type,
number of test ports, and lengths. Add appropriate frequency
extenders with required quantity for the measurements.
For complete list of millimeter-wave products and options, and
ordering instructions, please refer to 5989-7620EN Millimeter-
wave Network Analyzers Technical Overview.