Use and Care Manual

ManualsBrandsAgraLife ManualsExterior Stain & SealersVOC Free Non-Toxic Garden-Seal 1 gal. Clear Satin Wood Sealer

TRICOPOLYMERTM PRODUCTS

USE AND CARE SUGGESTIONS

Starting in 1995, the development of the Tricopolymer and its benefits are well

known. Moisture issues, labor cost, construction delays, all the issues are solved

when it comes to “cheaply” protect a structure, especially in flood-zone areas,

coastal structures, multi-family complexes, and more.

Watch any renovation TV shows? Renovators are always tearing out damaged

wood and materials, even on younger homes, or during building the structure

costing more time and money, materials and difficulty. Triple the importance for

use in flood and hurricane zones, water damaged structures, or salt water or

coastal zones. A must for sealing renovations prior to coverup.

Thru the years we have learned- It is the only sealant that is non-toxic, dries fast

and tough, clear, water based, water resistant, correct perm rate, prevents rust,

lasts 2-30+ years depending on application, scratch off resistant, chemical

resistant, plumbing and wire casings not effected, nail-pop reduced, makes a

great and economical primer, easy to apply, no harsh smells, no VOCs, water

cleanup, safe for children, pets and the environment. Easy maintenance, if any.

Can the Tricopolymer be applied anywhere?

Imagine being able to seal most surfaces inexpensively and non-toxically-to the

point of being able to seal a complete house, every wood frame and concrete

surface against water damage including fire resistance in the coating-applied to

the structure all over. A win-win for all involved. Flood-Zone rated, the

Tricopolymer can be applied on almost any surface in the construction world with

numerous benefits occurring, thus becoming very valuable to the structure,

Owner, and insurer over time.

Tested and applied by 150,000+ Consumers, millions of square feet applied,

chemical design and components independently tested and verified for many

years, real world result testing included.

Summary of content (5 pages)

PAGE 1
TRICOPOLYMER PRODUCTS TM USE AND CARE SUGGESTIONS Starting in 1995, the development of the Tricopolymer and its benefits are well known. Moisture issues, labor cost, construction delays, all the issues are solved when it comes to “cheaply” protect a structure, especially in flood-zone areas, coastal structures, multi-family complexes, and more.
PAGE 2
The pre-spraying of Frame wood, plywood, floor joists, subfloors, wet stubbed in areas, plumbing holes, ceiling tile, general sealing of drywall, sealing interior concrete floors, framing lumber, plywood, OSB plywood, sill plates, cement board, just to name a few additional uses as the home is built is simply a no brainer. Apply during 1-side completion –before coverup-labor usually using a power sprayer can complete the task in 3-4 hours to apply, fast drying-no down time for drying.
PAGE 3
destruction of property area. Cleanup is enhanced 80% by the pre-treatment of Tricopolymer. Use the Tricopolymer to pre-spray exterior core board prior to stucco attachment. Limited warranty exists for behind stucco use. The Tricopolymer can be used on exterior faces of stucco before painting to economically prime and seal the surface at half the cost of primer. Seal log cabins, barns, lap-board houses, farm houses, and more.
PAGE 4
✓ Preplan for drip cloths, wind conditions, and temperatures- Apply Product while stirring- or stir and pour off amount needed in a tray or small container. Keep lid tightly closed, especially on buckets ( Children may fall head first in half filled bucket and drown). Safety First - Wear eye protection, gloves, and old clothes. Protect your hair. Product is difficult to remove when dry. Apply in good weather. Freeze-proof when dry. May be slippery when wet. Keep young children and pets away while applying.
PAGE 5
Raising wood grain- For raw wood to become smooth, the wood fibers need to be “raised” in order to sand off the rough surface. Apply water to the surface, allow to dry, sand surface and repeat until desired surface result occurs. Then Seal. Some wood boards are economy cut and will always be rough due to crosscutting the wood grain. Sealing these will keep moisture from destroying the core.