Owner`s manual

ManualsBrandsAGRI-COVER ManualsRemote ControlCommand-10

Remote Control

Instructions

FOR New Tarp Remote

Control Installation

Use these in place of the “rocker

switch and solenoid “section of

instructions in your roll tarp

owner’s manual.

FOR Existing Electric Tarp

Remote Control Installation

Disconnect (+) and (-) battery

terminal connections. Disable

existing switch and solenoid - they

will not be used with this system.

Install the remote control in

accordance with these instructions

included with remote control kit.

READ AND UNDERSTAND THESE INSTRUCTIONS, WITH

REMOTE KIT FOR SAFETY, INSTALLATION, DANGER, OPERA-

TION, MAINTENANCE AND PROGRAMING FOR YOUR REMOTE

CONTROL PRODUCT. SAVE ALL INSTRUCTIONS WITH YOUR

ROLL TARP OWNERS MANUAL FOR FUTURE REFERENCE

IMPORTANT!

Summary of content (16 pages)

PAGE 1
Remote Control Instructions FOR New Tarp Remote Control Installation FOR Existing Electric Tarp Remote Control Installation Use these in place of the “rocker switch and solenoid “section of instructions in your roll tarp owner’s manual. Disconnect (+) and (-) battery terminal connections. Disable existing switch and solenoid - they will not be used with this system. Install the remote control in accordance with these instructions included with remote control kit.
PAGE 2
Dielectric Grease Packet Control Box Rubber Boots FOB Heat Shrink Terminals Bolts Washers and Nuts Parts Diagram (for part No. 80000) Parts included: The above diagram shows only parts that are included in the Command-5 remote control kit. All other parts shown in the following instructions would be found in a new electric tarp kit or would be already installed on an existing electric tarp system.
PAGE 3
Wiring Instructions 1 Note: There is ample heavy gauge wire supplied with each kit for standard installs. Before cutting wire, always preplan wire routing and make necessary adjustments as needed. Note: Use dielectric grease (packet included) at all ellectrical connections throughout installation. Route heavy gauge wire from battery to tarp motor. Allow ample wire where cutting and mounting connections take place. SEE Figure 1, box with hoist. Figure 2, semi-trailer box.
PAGE 4
5 6 7 For TRAILER UNITS with Heavy Duty connector use terminals to attach wire to socket. For motor terminal connections, if needed refer to electrical section of roll tarp owner’s manual. Now connect red wire to battery (+) post and then black wire to battery (-) post. Check operation of system. If system operates in reverse, switch motor wires under control box and retest.
PAGE 5
DUAL POLE CONNECTOR (USED IN SOME APPLICATIONS) Note: Use dielectric grease (packet included) at all electrical connections. NOTE: This remote system requires a 40 amp modified reset circuit breaker. When operating, holding switch until circuit breaker trips is TOO LONG. When this occurs, breaker will trip and reset if overloaded by the motor. To reduce unnecessary strain on components, always release switch before breaker trips.
PAGE 6
Learning How to Use and Operate Your AGRICOVER® Command-5™ Wireless Remote Introduction This wireless controller provides push-button wireless control. The key fob transmitter is simple to use and provides convenient reliable operation and is suitable for a wide variety of applications. The following instructions are directed to electric tarp installation and operation.
PAGE 7
Operating Instructions (how to use fobs pre-programmed mode to open and close tarp) Your roll tarp system can be operated wirelessly by the remote key fob. The key fob is designed to provide safe and easy operation of the tarp and features an auto-lock mode to help prevent unintended operation. Step 1 – To Unlock Key Fob When key fob is in lock mode, all 5 indicator lights will light up when pressing any button (Figure 1).
PAGE 8
Step 3 – To Lock Key Fob To manually lock key fob, press and hold both ON and OFF buttons at the same time for 3 seconds. Flashing light indicator will stop, indicating fob is in lock mode (Figure 4). If fob is unlocked and left idle for 3 minutes or more, it will automatically go into lock mode. Fob is in lock mode when pressing any button and all 5 indicator lights light up.
PAGE 9
Optional Instructions to Enable and Program Additional Modes on Key Fob Note: Mode 1 (tarp) cannot be disabled. During program mode, if fob is left idle for more than 10 seconds, it will return to operating mode. Turn key fob on. Press and hold SELECT button for 10 seconds until far left light is on continuous (Figure 5). The fob is now in programming mode. Press ON button to enable current mode shown by lit LED or press OFF button to disable current mode shown by lit LED.
PAGE 10
Instructions to Re-Program Key Fobs or Receivers Your Roll Tarp Wireless System is typically pre-programmed at the factory ready to use. Re-programming is necessary if replacement fobs or receivers are installed. Use programming method below to program receiver to accept/respond to signals from up to 5 key fobs. 1. Gain access to receiver inside control box. 2. Make sure receiver is connected to power source. If ON/OFF switch is installed, turn it on. 3.
PAGE 11
Instructions to Program a Receiver (To More Than 1 Fob) To program a receiver that controls the tarp motor to recognize more than 1 fob. Example given below does 3 fobs. 1. Remove control box cover. Turn 3 fobs on. 2. Set all 3 fobs to same tarp motor. 3. Press and hold programming button on receiver for 5 seconds. Receiver will beep to indicate it is in Programming Mode. Release programming button. 4. Press ON button on 1st fob.
PAGE 12
Battery Replacement NOTE: The COMMAND-5 Remote will indicate low battery levels by flashing all 5 LEDs when both the ON and the OFF buttons are pressed at the same time. Your wireless key fob is powered by two 23A 12V batteries. If key fob becomes unresponsive replace batteries. To change batteries, remove 4 screws from back of fob using a small phillips screwdriver. Carefully remove front of fob exposing two batteries. Replace both batteries with two of same brand and size.
PAGE 13
Trouble Shooting Receiver Problem Issue: Check or Try... 1. Two different motors operate at the same time when using fob remote. .….reprogram receiver that is malfunctioning. (Review receiver programming page 10 with attention to Step 7) 2. System will not operate with fob remote or toggle switch. (Cannot hear a clicking noise from receiver inside control box.) ….. if system has a master control switch, make sure it is turned to “ON” position. .…. auto circuit breaker may have tripped.
PAGE 14
Trouble Shooting Receiver Cont’d Problem Issue: 3. System will not operate with fob remote or toggle switch. (Can hear a clicking noise from inside receiver control box—but nothing happens.) 4. The key fob and toggle switch will operate the tarp motor, but motor turns freely and tarp doesn’t move. 14 Check or Try... …..verify there is at least 12 volts on back side of receiver on battery hookup posts. …..
PAGE 15
Trouble Shooting Key Fob Problem Issue: Check or Try... 1. Key fob transmitter doesn’t work. None of the lights turn on when remote is turned on. …..check fob for dead batteries, make sure batteries are loaded correctly in remote. ….. remove batteries and make sure contacts are tight and not corroded. Reinsert batteries and try again. …..batteries may be dead, replace with new quality high capacity batteries. …..damaged fob transmitter, replace fob. 2. Key fob transmitter doesn’t work.
PAGE 16
Trouble Shooting System Problem Issue: Check or Try... 1. System will not operate with .…. if system was just installed, check to toggle switch or with fob transmitter. Motor engages but stalls and tarp does not turn. see if tarp operates in opposite direction. If so, see wiring installation about reversing wires. …..check condition of tarp and alignment. 2. Key fob transmitter doesn’t work. System operates with toggle switch but not remote fob.