™ OWNERS MANUAL MANUAL DEL USUARIO NOTICE D’UTILISATION Model No. Modelo No. Modèle No. 45-03295 175 LB. ATV BROADCAST SPREADER CAUTION: Read Rules for Safe Operation and Instructions Carefully PRECAUCION: Lea cuidadosamente los Procedimientos e Instrucciones para la Operación Segura de la Máquina. ATTENTION: Lire et suivre attentivement les instructions et consignes de sécurité de cette notice.
CARTON CONTENTS (Loose Parts in Carton) CONTENIDO DE LA CAJA (Partes Sueltas en la Caja) CONTENU DU CARTON (Pièces en Vrac Dans le Carton) 2 4 OF F 3 ON 10 9 8 7 6 5 4 3 2 1 1 5 7 6 ENGLISH 1 2 3 4 5 6 7 ESPAÑOL Hitch Tube Wheels (2) Hopper Assembly Flow Control Mounting Tube Hopper Cover Screen Flow Control Rod 1 2 3 4 5 6 7 FRANÇAIS Tubo de Enganche Ruedas (2) Conjunto de la Tolva Tubo de Montaje del Control de Flujo Tapa de la Tolva Malla Varilla de control 1 2 3 4 5 6 7 C A Tu
ENGLISH RULES FOR SAFE OPERATION Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when operating equipment. • • • • • Read the towing vehicle owners manual and towing vehicle safety rules. Know how to operate your tractor before using the broadcast spreader attachment. Read the chemical label instructions and cautions for handling and applying the chemicals purchased for spreading.
ENGLISH ASSEMBLY INSTRUCTIONS 4. Assemble the two OUTER hitch braces to the hitch tube using a 1/4" x 1-3/4" (B) hex bolt and a 1/4" nylock hex nut (C). DO NOT TIGHTEN YET. Do not assemble the inner hitch braces at this time. See figure 2. TOOLS REQUIRED FOR ASSEMBLY (1) (2) (2) (2) Pliers 7/16" Wrenches 1/2" Wrenches 9/16" Wrenches HITCH TUBE REMOVAL OF PARTS FROM CARTON Remove all parts and hardware packages from the carton.
ENGLISH 12. Insert the hook end of the flow control rod through the hole in the slide gate bracket located under the hopper. See figure 6. 7. Assemble a spacer (I), a 3/4" flat washer (G), a wheel (air valve facing out) and another 3/4" flat washer (G) onto the end of the axle that has both the large and small holes. See figure 4. 8. Install a 1/8" x 1-1/2" cotter pin (E) into the small hole in the end of the axle. See figure 4. 9.
ENGLISH 14. Assemble the two INNER hitch braces to the flow control mounting tube using a 1/4" x 1-3/4" hex bolt (B) and a 1/4" nylock hex nut (C). DO NOT TIGHTEN YET. See figure 8. 15. TIGHTEN all nuts and bolts assembled up to this point. Do not collapse the tubes when tightening. 16. Calibrate the flow control setting. (See figure 9). a. Push flow control arm to "OFF" position. b. Slide flow control mounting bracket along tube until closure plate in bottom of hopper just closes. c.
ENGLISH 17. Place the screen down into the hopper, sliding the edge of the screen under one of the clips. Slightly bow the screen to slide the opposite side of the screen under the other clip. See figure 10. 18. For most vehicles, you can keep the assembled hitch extension bracket in its default position shown in figure 11. Attach the spreader hitch to your vehicle hitch. Check for interference with the spreader directly behind and out to both sides of the vehicle.
ENGLISH OPERATION 10. To insure uniform coverage, make each pass so that the broadcast pattern slightly overlaps the pattern from the previous pass as shown in figure 12. The approximate broadcast widths for different materials are shown in the application chart on this page. 11. When broadcasting weed control fertilizers, make sure the broadcast pattern does not hit evergreen trees, flowers or shrubs. 12. Heavy moisture conditions may require a cover over the hopper to keep contents dry.
ENGLISH MAINTENANCE SERVICE AND ADJUSTMENTS CHECK FOR LOOSE FASTENERS 1. Before each use make a thorough visual check of the spreader for any bolts and nuts which may have loosened. Retighten any loose bolts and nuts. REPLACING SLOTTED GEAR 1. If the axle, slotted gear and sprocket assembly is disassembled, mark down the positions of the parts as they are removed.The drive wheel and sprocket positions in relation to the slotted gear determine which direction the spreader plate will spin.
FRANÇAIS CONSIGNES DE SÉCURITÉ Tout appareil mécanique risque de provoquer des blessures si ce dernier n’est pas utilisé correctement ou si l’utilisateur ne sait pas comment l’utiliser. Faites preuve de prudence à tout moment lorsque vous utilisez un appareil mécanique. • • • • • Lisez cette notice d’utilisation et les consignes de sécurité avant de tenter d’assembler ou d’utiliser la remorque. Veillez à bien connaître le fonctionnement du tracteur avant d’atteler la remorque à l’épandeur.
FRANÇAIS 4. Montez les deux entretoises d’attelage EXTÉRIEURES sur le tube d’attelage en utilisant un boulon hex. (B) et un contreécrou hex. (C). NE PAS SERRER POUR L’INSTANT. Ne pas fixer les entretoises d’attelage intérieures pour l’instant. Voir la Figure 2. 5. Montez un tube d’espacement (I) et une rondelle plate (G), une roue (avec la valve vers l’extérieur) et une autre rondelle plate (G) sur l’extrémité de l’essieu qui comporte un petit trou. Voir la figure 3. 6.
FRANÇAIS UTILISATION 10. Pour une couverture optimale et afin d’éviter de manquer des zones ou de laisser des traces de passages, chevauchez les traces précédentes comme illustré à la figure 12. Les portées approximatives des différentes matières sont indiquées dans le tableau des débits de cette page. 11. Faites attention lorsque vous utilisez l’épandeur avec des herbicides et désherbants et veillez à ce que ces produits ne touchent pas les buissons, les fleurs, etc. 12.
FRANÇAIS ENTRETIEN ET MAINTENANCE REMISAGE 1. VÉRIFIER QUE LA VISSERIE N’EST PAS DESSERRÉE 1. Avant toute utilisation, vérifiez attentivement que les boulons et les écrous de l’épandeur ne sont pas desserrés. Serrez tout boulon ou écrou desserré. 2. VÉRIFIER QUE LES PIÈCES NE SONT PAS USÉES OU ENDOMMAGÉES 2. Vérifiez que les pièces ne sont pas usées ou endommagées avant chaque utilisation. Réparez ou remplacez la pièce si nécessaire.
ESPAÑOL REGLAS PARA OPERACIONES SEGURAS Recuerde, cualquier equipo motorizado puede causar lesiones si se opera incorrectamente o si el usuario no entiende cómo operar el equipo. Sea precavido en todo momento al usar equipo motorizado. • • • • • • Lea el manual del propietario y las reglas de seguridad del vehículo de arrastre. Aprenda cómo operar su tractor antes de usar el implemento Esparcidor de Lanzado.
ESPAÑOL 4. Instale los dos puntales de enganche EXTERIORES en el tubo de enganche usando un perno hexagonal (B) y una tuerca de cierre hexagonal (C). NO APRIETE TODAVIA. No instale en este paso los puntales de enganche interiores. Vea la Figura 2. 5. Ensamble un espaciador (I), una arandela plana (G), una rueda (con la válvula de aire mirando hacia fuera) y otra arandela plana (G) sobre el extremo del eje que sólo tiene el hueco pequeño. Ver figura 3. 6.
ESPAÑOL OPERACIÓN 10. Para garantizar un cubrimiento uniforme, realice cada pasada superponiendo ligeramente el patrón de lanzado de la pasada anterior, según se muestra en la figura 12. Los anchos aproximados de lanzado para los diferentes materiales, se muestran en el cuadro de aplicación en esta página. 11. Cuando aplique fertilizantes para control de hierbas o malezas, asegúrese de que el patrón de lanzado no llegue a los árboles de verde perenne, a las flores ni a los arbustos. 12.
ESPAÑOL MANTENIMIENTO ALMACENAMIENTO REVISE SI HAY ELEMENTOS DE AJUSTE SUELTOS 1. Antes de cada uso, realice una revisión visual detallada del esparcidor en busca de pernos o tuercas sueltos o flojos. Vuelva a apretar los pernos o las tuercas flojas. 1. 2. REVISE SI HAY PARTES GASTADAS O DAÑADAS 2. Antes de cada uso, revise si hay partes gastadas o dañadas. Repare o reemplace las partes cuando sea necesario.
REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-03295 9 45 58 47 54 54 39 64 F OF 51 ON 1 2 3 4 5 38 7 8 9 35 37 9 11 2 39 58 34 61 54 39 41 63 35 58 37 39 42 9 39 53 9 54 65 B 40 6 10 9 30 40 9 39 13 66 58 44 8 60 B 1 A 4 31 40 3 59 26 27 4 12 9 28 9 40 57 6 D 9 C 32 7 52 E 36 29 23 24 50 24 67 55 13 7 13 23 21 18 50 A 19 E 67 33 25 10 49 15 35 46 7 62 9 29 58 37 9 5 43 20 21 22 9 14 19 17 D 53 35 16 15 48 49 67 5
REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-03295 REF. QTY. PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 * 1 4 1 1 1 1 5 1 22 1 2 2 6 1 2 1 1 1 2 1 5 1 2 2 1 1 1 1 2 2 1 3 2 1 44480 41157 65129 44462 23753 23758 HA21362 24857 47189 43808 43084 44180 47810 48864 48511 25080 23014 24914 43851 43871 1540-32 1540-162 47615 47683 25305 04367 43850 44468 44285 25672 48934 43070 43054 41549 DESCRIPTION REF. QTY. PART NO.
the fastest way to purchase parts www.speedepart.com REPAIR PARTS Agri-Fab, Inc. 809 South Hamilton Sullivan, IL. 61951 217-728-8388 www.agri-fab.com This document (or manual) is protected under the U.S. Copyright Laws and the copyright laws of foreign countries, pursuant to the Universal Copyright Convention and the Berne convention.