™ OWNERS MANUAL Model No. 45-02104 125 LB. PUSH BROADCAST SPREADER CAUTION: Read Rules for Safe Operation and Instructions Carefully Assembly Operation Maintenance Repair Parts the fastest way to purchase parts www.speedepart.com PRINTED IN U.S.A. FORM NO. 41078 (Rev.
RULES FOR SAFE OPERATION The following safety precautions are suggested. This broadcast spreader is designed, engineered and tested to offer reasonably safe and effective service, provided it is operated in strict accordance with these instructions. Failure to do so may result in personal injury. Always observe the rules of safe operation. 3. Wear eye and hand protection when handling and when applying lawn or garden chemicals. 4.
SHOWN FULL SIZE A C B E D H G F I J NOT SHOWN FULL SIZE K L P R Q DESCRIPTION O N M KEY QTY. KEY QTY. A 2 Hex Bolt, 1/4-20 x 1-3/4" Long J 1 Cotter Pin, 3/32" x 3/4" Long B 5 Hex Bolt, 1/4-20 x 1-1/2" Long K 1 Flow Control Link C 2 Hex Bolt, 1/4-20 x 1" Long L 2 Spacer Tube D 1 Carriage Bolt, 1/4-20 x 3/4" Long M 2 Hub Cap E 9 Nyock Nut, 1/4-20 Thd.
ASSEMBLY INSTRUCTIONS 5. Place a wheel onto the end of the axle that has a cross hole. The long end of the hub goes to the inside. See figure 3. 6. Assemble a 5/32" x 2" cotter pin through the hole in the wheel hub and the axle. See figure 3. 7. Place a 5/8" flat washer onto the axle and then lightly tap a hub cap onto the axle until it is snug against the washer and wheel hub. See figure 3. TOOLS REQUIRED FOR ASSEMBLY (1) Pliers (1) Hammer (2) 7/16" Open or Boxed End Wrenches 1. 2.
IMPORTANT: Do Not asssemble handle tube to same side of crossover tube as shaft support plate. 9. 13. Assemble the leg stand tube to the handle tube (long) using two 1/4" x 1-1/2" hex bolts. Secure tightly with two 1/4" nylock nuts. See figure 6. Place the long handle tube onto the crossover tube on the side opposite from the shaft support plate. Fasten with the bolt, washer and nut removed in the previous step. See figures 4 and 5. Do not tighten at this time. 14.
16. Assemble the flow control arm to the flow control mounting bracket using a 1/4" x 1" hex bolt, two nylon washers and a 1/4" nylock nut as shown in figure 8. Tighten carefully. The flow control arm should be snug, but should pivot with no more than a slight resistance. 17. Assemble the vinyl grip. See figure 8. 19. Hook the free end of the flow control rod through the hole in the slide gate bracket located near the bottom of the hopper. See figure 10.
22. Place the adjustable stop into the "ON" end of the slot in the top of the flow control mounting bracket. Secure with the 1/4" x 3/4" carriage bolt, a nylon washer, a 5/16" flat washer and the nylon wing nut. See figure 12. 23. Position the flow control mounting bracket (figure 13). a. Push on flow control arm until it locks in "OFF" position. b. Slide flow control mounting bracket along tube until closure plate in bottom of hopper just closes. c.
OPERATION APPLICATION DIAGRAM HOW TO USE YOUR SPREADER SETTING THE FLOW CONTROL (Refer to figure 13 on page 7.) 1. 2. 3. 8' to 10' Loosen the nylon wing nut, set the adjustable stop to the desired flow rate setting and retighten the wing nut. The higher the setting number, the wider the opening in the bottom of the hopper. Refer to the application chart on page 8 and to the instructions on the fertilizer bag to select the proper flow rate setting.
MAINTENANCE SERVICE AND ADJUSTMENTS CHECK FOR LOOSE FASTENERS 1. Before each use make a thorough visual check of the spreader for any bolts and nuts which may have loosened. Retighten any loose bolts and nuts. REPLACING SLOTTED GEAR 1. If the axle, slotted gear and sprocket assembly is disassembled, mark down the positions of the parts as they are removed. The drive wheel and sprocket positions in relation to the slotted gear determine which direction the spreader plate will spin.
REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-02104 52 51 37 29 40 16 32 39 37 14 39 29 11 C 1 31 5 9 13 32 9 9 A B 40 9 41 42 47 7 28 3 24 25 11 4 32 26 30 7 D 15 21 23 22 9 18 9 40 9 7 10 9 29 19 32 34 49 27 D 7 A 18 35 E 17 7 9 15 21 20 20 43 4 E 21 B 35 50 C 6 36 28 11 39 45 9 46 33 38 7 9 21 48 44 40 39 8 9 22 9 10 23 21 50
REPAIR PARTS LIST FOR BROADCAST SPREADER MODEL 45-02104 REF. NO. 1 2 3 4 5 6 7 8 9 10 11 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION NO. NO. NO. 44466 1 Hopper 28 44285 2 Bushing, Delrin 3/8" I.D. C-9M5732 2 Pop Rivet (not shown) 29 1509-69 9 Bolt, Hex 1/4-20 x 1-3/4" Lg.* 62482 1 Ass'y, Guide Closure 30 47063 1 Pin, Cotter 5/32" x 2" 48842 1 Tube, Frame 31 48934 1 Hairpin, Agitator 23753 1 Slide Gate Angle Bracket 32 43088 16 Washer, Flat 1/4" Std.
the fastest way to purchase parts www.speedepart.com REPAIR PARTS Agri-Fab, Inc. 303 West Raymond Sullivan, IL. 61951 217-728-8388 www.agri-fab.com This document (or manual) is protected under the U.S. Copyright Laws and the copyright laws of foreign countries, pursuant to the Universal Copyright Convention and the Berne convention.
