™ APPLICATIONTIPS xxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx owners manual xxxxx xxxxx xxxxxxxxxxxxxxxx xxxxx xxxxx xxxxx xxxxxx xxxxxx xxxxxx xxx xxx xxx xxxxxx xxxxx xxxxxx Model No. 45-02153-131 100 LB.
RULES FOR SAFE OPERATION Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when operating equipment. • • • • • • Read the towing vehicle owners manual and towing vehicle safety rules. Know how to operate your tractor before using the broadcast spreader attachment. Read the chemical label instructions and cautions for handling and applying the chemicals purchased for spreading.
5. Assemble the two hitch braces to the hitch tube using a 1/4" x 1-1/2" hex bolt and a 1/4" nylock nut. See figure 3. Do not tighten at this time. 6. Tighten all loose hex nuts and bolts attached to hitch tube and hitch braces. Do not collapse tubes when tightening. 8. Place the drive wheel onto the end of the axle that has an indent. The long end of the hub goes to the inside. See figure 5. 9. Place a hub cap onto the end of the axle.
OPERATION 12. Position the flow control mounting bracket (figure 7). a. Push on flow control arm until it locks in "OFF" position. b. Slide flow control mounting bracket along tube until closure plate in bottom of hopper just closes. c. Snug the 1/4" lock nuts just enough to hold flow control mounting bracket in place. d. Set adjustable stop at "5". Pull flow control arm against stop. Verify that closure plate has opened about half way. e.
CLEANING 4. Rinse inside of hopper and exterior of spreader and dry off before storing. LUBRICATE (See figure 9.) 5. Lightly apply automotive grease as needed to the sprocket and gear. 6. Oil the nylon bushings on the vertical sprocket shaft and on the axle at least once a year, or more often as needed. 7. Oil right hand (idler) wheel bearing at least once a year or more often as needed.
REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-02153-131 49 15 4 1 A 12 31 40 5 39 9 13 40 9 9 50 11 33 7 3 2 40 26 A 27 4 9 11 E B 9 25 B D 40 9 10 19 34 46 12 11 28 35 6 36 33 42 45 21 18 43 20 21 22 32 D 17 9 14 47 11 51 50 9 8 39 7 9 11 35 22 39 32 32 E 22 44 37 32 7 23 48 22 24 19 9 24 23 16 6 9 39 32 41 38 7
REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-02153-131 REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 PART NO. 44624 46055 62482 40469 23753 23758 43661 24857 47189 44591 43648 1509-69 44566 44586 40539 40540 23687 23781 44665 44672 44137 R19171616 47963 46501 25305 04367 QTY 1 1 1 1 1 1 5 1 22 1 9 7 1 1 1 1 1 1 2 1 6 4 2 2 1 1 DESCRIPTION REF Hopper Pin, Spring 1/8" Dia. x 1" Lg.
the fastest way to purchase parts www.speedepart.com © 2007 Agri-Fab, Inc REPAIR PARTS Agri-Fab, Inc. 809 South Hamilton Sullivan, IL. 61951 217-728-8388 www.agri-fab.