OWNERS MANUAL Model No. 45-02182 26" LEAF/LAWNSWEEPER CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operating Maintenance Repair Parts Call 1-800-448-9282 for missing parts or assembly help. the fastest way to purchase parts www.speedepart.com PRINTED IN USA FORM NO. 40231 rev.
SAFETY RULES Remember, any equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when using this equipment. CAUTION: VEHICLE BRAKING AND STABILITY MAY BE AFFECTED WITH THE ADDITION OF AN ACCESSORY OR AN ATTACHMENT. BE AWARE OF CHANGING CONDITIONS ON SLOPES. LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS — ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED.
ASSEMBLY INSTRUCTIONS HARDWARE PACK (NOT SHOWN FULL SIZE) 1. A B Turn the sweeper upside down. Place a brush assembly on the brush shaft, with the short ends of the brushes at the center of the sweeper and the overlap bristles of the top brush facing out. Install two 1/4" x 1" hex bolts and 1/4" nylock nuts. See figure 1. 2. Rotate the brushes 1/4 turn and repeat step 1 for the second brush. C 1/4" NYLOCK NUT D HEX BOLT 1/4-20 x 1" E Ref. Part No.
. Assemble the Upper Handle Tube over the Handle Leg Stand Tubes. Align holes in handle and assemble the Bag Rod Clips to the handle as shown and fasten with 1/4" x 1-1/4" hex bolts and nylock nuts. See figure 3. 7. Slide the long bag rod (28-1/2" long) through the stitched bag flap on the top of the hopper bag as shown in figure 5. 8. Slide the short bag rod (25-1/2" long) through the stitched bag flap on the bottom of the hopper bag as shown in figure 5.
10. Assemble the two 3/4" x 7/8" plastic caps onto the ends of the leg stands as shown in figure 7. 12. Place the lower hopper bag and bag rod into the opening on the sweeper housing. See figure 9. FIGURE 7 FIGURE 9 11. Place the upper hopper bag and bag rod into the bag rod clips on the hopper handle. See figure 8. 13. Hook the elastic straps on the bag flaps under the bag rod clips on the lower handle tubes as shown in figure 10.
OPERATION STORAGE Take care when operating your sweeper. Operating your sweeper according to these instructions will help prevent damage and prolong the life of your sweeper. The entire unit may be hung on a wall or the hopper bag frame can be removed for storage. BRUSH HEIGHT ADJUSTMENT LUBRICATION/MAINTENANCE To adjust your sweeper brushes to the best operating height, loosen the hand knob and slide the height adjustment tube down to raise or up to lower the brushes.
WHEEL GEARS/PAWL SERVICE BRUSH REPLACEMENT IMPORTANT: Do not remove both wheels at the same time to avoid mixing parts. (The R.H. and L.H. ratchet gears are not interchangeable.) Make notes on the position of washers and snap rings during disassembly. 1. Remove the hopper bag from lawnsweeper. 2. Brush replacement should be done one brush at a time. 3. Tip the sweeper forward on housing for ease of brush replacement. Do not remove hex bolt from double brush retainers through brush shaft. 4.
REPAIR PARTS FOR 45-02182 26" LEAF/LAWNSWEEPER 46 46 46 46 8
REPAIR PARTS FOR 45-02182 26" LEAF/LAWNSWEEPER REF. NO. 1 4 5 6 7 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 PART NO. QTY. 44600 43681 44680 1543-69 44695 43720 44946 23866 44598 43070 44684 1038 44685 40007 716-0106 44679 49946 741-0249 43182 47810 2674-32 48651 48652 47046 1 1 1 1 2 1 1 2 2 4 2 2 2 2 2 2 2 4 4 4 2 1 1 2 REF. NO.
NOTES 10
NOTES 11
the fastest way to purchase parts www.speedepart.com REPAIR PARTS Agri-Fab, Inc. 303 West Raymond Sullivan, IL. 61951 217-728-8388 www.agri-fab.com This document (or manual) is protected under the U.S. Copyright Laws and the copyright laws of foreign countries, pursuant to the Universal Copyright Convention and the Berne convention.