™ OWNERS MANUAL Model No. 45-02881 175 LB. POLY PRO DROP SPREADER CAUTION: Read Rules for Safe Operation and Instructions Carefully • • • • • Safety Assembly Operation Maintenance Parts the fastest way to purchase parts www.speedepart.com PRINTED IN U.S.A. FORM NO. 47717 (REV.
RULES FOR SAFE OPERATIONS Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment. • • • • • • • Read this owner's manual before attempting to assemble or operate the spreader. Read the towing vehicle owner's manual and know how to operate the tractor before using the spreader attachment. Do not allow anyone to ride on or sit on spreader.
SHOWN FULL SIZE G F A B C D E I H J K NOT SHOWN FULL SIZE L M HARDWARE CHART REF. A B C D E F G QTY. 1 1 2 10 1 4 3 REF. QTY.
ASSEMBLY 1/4" NYLOCK NUTS 1/4" x 1-1/4" HEX BOLT TOOLS REQUIRED FOR ASSEMBLY PLASTIC GRIP (2) 7/16" Wrenches (2) 9/16" Wrenches 1/4" FLAT WASHER 1. Remove the hardware pack and all individual parts from the carton and lay out as shown on page 2 and 3. NYLON WASHER HOPPER BRACE FLOW CONTROL ROD 2. Assemble the tongue to the hopper as shown in figure 1 using two 1/4" x 5/8" hex bolts and 1/4" nylock nuts. Do not tighten yet. FLOW CONTROL ARM FERRULE 1/2" FIGURE 2 6.
8. Assemble one end of a tongue brace to the side of the tongue using two 1/4" x 5/8" hex bolts and 1/4" hex nuts. Do not tighten yet. See figure 4. 12. Assemble the flow control gauge to the hopper brace using the 1/4" x 3/4" carriage bolt, a nylon washer and the plastic knob. See figure 6. 9. Assemble the other end of the tongue brace to the triangular plate on the end of the spreader. Use a 1/4" x 5/8" hex bolt and 1/4" nylock nut in the front hole of the plate.
OPERATION SETTING CHART HOW TO USE YOUR SPREADER MATERIAL Flow Rate Setting TYPE At 3 M.P.H. Fertilizer Granular / Pelleted 0-1 / 0-2 Grass Seed Fine / Coarse 5-6 / 7-8 1. Refer to the instruction label on the material package and to the instruction decal on your spreader to help determine the proper spreader setting and application rate. Also see the Setting Chart on this page for a general range of settings for commonly used materials. 2.
REPAIR PARTS FOR 175 LB. DROP SPREADER MODEL 45-02881 37 5 3 27 26 6 5 2 18 17 19 42 16 21 5 11 6 8 B A 11 16 41 5 4 4 35 35 29 6 19 1 36 28 6 15 A 4 23 22 24 20 16 7 6 4 19 35 33 5 38 34 25 10 5 15 13 14 B 9 6 31 12 6 6 REF. PART NO. NO. 1 47451 2 24536 3 24535 4 43088 5 43866 6 47189 7 741-0245 8 47484 9 24538 10 24539 11 47711 12 728-3001 13 47459 14 47508 15 24537 16 43009 17 47259 18 47476 19 24540 20 46497 21 47458 22 24534 6 30 QTY.
the fastest way to purchase parts www.speedepart.com REPAIR PARTS 303 West Raymond Sullivan, IL. 61951 217-728-8388 www.agri-fab.