OWNERS MANUAL Model No's. 45-0294 (40") 45-0295 (48") TINE DE-THATCHER CAUTION: Read Rules for Safe Operation and Instructions Carefully PRINTED IN USA Assembly Operation Maintenance Repair Parts FORM NO. 47634 (REV.
RULES FOR SAFE OPERATIONS Remember, any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS -- ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED. CAUTION: VEHICLE BRAKING AND STABILITY MAY BE AFFECTED WITH THE ADDITION OF AN ACCESSORY OR AN ATTACHMENT. BE AWARE OF CHANGING CONDITIONS ON SLOPES. Exercise caution at all times when using power equipment. 1.
SHOWN FULL SIZE A B C D E F G K H L I J NOT SHOWN FULL SIZE N M HARDWARE PACK Key A B C D E F G H Qty. 40" 48" Description 2 2 2 15 14 1 1 14 Shoulder Bolt Hex Bolt, 5/16" x 2" Lg. Hex Bolt, 5/16" x 1-1/4" Lg. Hex Bolt, 5/16" x 3/4" Lg. Carriage Bolt, 5/16" x 1" Hitch Pin, 3/8" Hair Cotter Pin, 1/8" Hex Nut, 5/16" 2 2 2 15 16 1 1 16 Key I J K L M N 3 Qty.
5. Fasten the hitch mount arms to the outside of the angle brackets at the front of the tine shield. Use two 5/16" x 3/4" hex bolts and 5/16" hex lock nuts. Tighten and then loosen the nuts slightly. See figure 3. 6. Fasten the hitch mount arms to the outside of the hitch arm mount brackets at the rear of the tine shield. Use two 5/16" x 1" carriage bolts, 5/16" lock washers and 5/16" hex nuts. Do not tighten yet. See figure 3.
11. Assemble the axle bracket on the outside of the angle brackets using two 5/16" x 3/4" hex bolts and 5/16" hex lock nuts. The ends of the axle bracket must point as shown in figure 5. Tighten and then loosen the bolts and nuts slightly. 14. Assemble the spring align wires through the front and rear rows of spring tines, passing the wires in between the hitch mount arms and the tine shield. Bend the ends of the wires to secure them. See figure 8.
5. If the de-thatcher appears to be "jumping" during use, then extra weight should be added to the tine shield. In most conditions extra weight will be needed. Concrete patio blocks are recommended for weight because of their low profile; however any type of weight is suitable if it can be tied down to the shield. Secure weight by using suitable binding material such as rubber tie down straps or wire, fastening to the holes in the shield flange. See figure 11.
TINE DE-THATCHER REPAIR PARTS MODEL NO's. 45-0294 (40") & 45-0295 (48") 15 8 6 15 15 15 19 4 18 3 20 4 10 14 16 17 18 12 12 15 18 1 11 15 9 16 12 17 13 16 18 18 7 17 13 2 15 12 22 2 5 18 REF. NO. PART NO. QTY.
AGRI-FAB ® LIMITED WARRANTY WHO IS COVERED: This Warranty covers only the original retail purchaser of an AGRI-FAB ® product or part. It is not transferable. HOW LONG DOES COVERAGE LAST: This Warranty remains in force for 1 year from the date of purchase. WHAT IS COVERED: Any defect in material or workmanship of your AGRI-FAB ® product or part. WHAT IS NOT COVERED: 1. This warranty does not apply to the engine or components parts thereof.