™ OWNERS MANUAL Model No. 45-0299 48" PLUG AERATOR CAUTION: Read Rules for Safe Operation and Instructions Carefully Assembly Operation Maintenance Repair Parts the fastest way to purchase parts www.speedepart.com PRINTED IN USA FORM NO.
RULES FOR SAFE OPERATIONS Remember, any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. CAUTION: VEHICLE BRAKING AND STABILITY MAY BE AFFECTED WITH THE ADDITION OF AN ACCESSORY OR AN ATTACHMENT. BE AWARE OF CHANGING CONDITIONS ON SLOPES. LOOK FORTHIS SYMBOLTO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS -- ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED. Exercise caution at all times when using power equipment. 1.
SHOWN FULL SIZE A C B D E G F H O L M I P J N S K Q R T NOT SHOWN FULL SIZE U W V HARDWARE PACKAGE CONTENTS Key Qty. A B C D E F G H I J K L 2 3 6 6 8 32 1 1 2 12 40 3 Description Hex Bolt, 1/2" x 3-1/2" Lg. Hex Bolt, 1/4" x 1-3/4" Lg. Hex Bolt, 3/8" x 1-1/4" Lg. Hex Bolt, 3/8" x 1" Lg. Hex Bolt, 5/16" x 3/4" Lg. Carriage Bolt, 5/16" x 3/4" Hitch Pin Hair Cotter Pin Nylock Jam Nut, 1/2" Nylock Nut, 3/8" Nylock Nut, 5/16" Nylock Nut, 1/4" Key Qty.
ASSEMBLY INSTRUCTIONS 3. Assemble a wheel bracket to the middle hole in the shaft so that the hub of the bracket faces the short end of the shaft. Fasten the bracket to the shaft using a 1/4" x 1-3/4" hex bolt and a 1/4" nylock nut. Tighten. See figure 2. TOOLS REQUIRED FOR ASSEMBLY (2) 7/16" wrenches (2) 1/2" wrenches (2) 9/16" wrenches (2) 3/4" wrenches or adjustable wrenches 4. Pre-assemble a 3/8" x 1-1/4" hex bolt and a 3/8" nylock nut to the smaller hole in the wheel bracket.
6. Assemble a 2.38" long spacer, a 3/4" flat washer, the middle brace, a 3/4" flat washer and a 3.90" long spacer onto the long end of the shaft. The bent lip of the middle brace must face the short end of the shaft. Next assemble a double spool assembly, a 5.29" long spacer, another double spool assembly, a 1.00" long spacer and a 3/4" flat washer onto the shaft. See figure 4. 2.38" LONG SPACER 8. Assemble a wheel to a wheel bracket using a 1/2" x 31/2" hex bolt, a 1/2" jam nut and a1/2" nylock jam nut.
11. Assemble the tongue to the tray, placing the slot's locking notch to the front. Use two 3/8" x 1" hex bolts, two 3/8" x 1-1/4" hex bolts, four 1/4" long spacers, and four 3/8" nylock nuts as shown in figure 8. Tighten. 13. Place the tray between the end plates. Temporarily insert three 5/16" x 3/4" hex bolts to hold the tray and end plates together at the corners. Leave one upper corner empty. See figure 9. 12.
16. Place the lift handle through the slot in the tray. Fasten the lift handle to the smaller, inner hole in the middle wheel bracket using the bolt and nut which you preassembled earlier (figure 2). Fasten the lift handle to the larger, outer hole in the wheel bracket using a 3/8" x 1-1/4" hex bolt, the shoulder spacer, and a 3/8" nylock nut. Tighten both nylock nuts. See figure 11. CAUTION: The Lift Handle can drop to the rear unexpectedly.
OPERATION MAINTENANCE Aerating means pulling small soil plugs, ranging up to three inches in length, from the soil to create small reservoirs that will bring oxygen, fertilizer and water down into the roots. For best aerator performance, the following lawn preparations and operating procedures are recommended. 1. Plugger points can periodically be sharpened with a small grinder to maintain good penetration. Points should be removed to sharpen. Follow original angle and contour of points when grinding. 2.
NOTES
REPAIR PARTS FOR 48" PLUG AERATOR MODEL 45-0299 8 13 12 12 9 27 13 12 14 13 1 12 3 19 21 17 3 17 5 13 34 27 9 17 23 26 17 7 22 8 25 24 27 30 28 17 33 35 28 10 4 28 12 18 32 10 28 23 2 17 17 12 22 9 29 27 31 27 28 6 28 10 32 28 28 30 21 20 36 10 37 27
REPAIR PARTS FOR 48" PLUG AERATOR MODEL 45-0299 REF. PART NO. NO. 1 24625 2 24623 3 24619 4 24624 5 24103 6 24626 7 23687 8 46503 9 63931 10 63929 12 43087 13 43001 14 23625 17 HA21362 18 44685 19 43182 20 43086 21 47810 22 1509-69 QTY. 1 1 2 1 1 1 1 2 3 4 6 6 8 12 1 8 32 40 3 DESCRIPTION REF. NO. PART NO.
the fastest way to purchase parts www.speedepart.com REPAIR PARTS Agri-Fab, Inc. 303 West Raymond Sullivan, IL 61951 217-728-8388 www.agri-fab.com This document (or manual) is protected under the U.S. Copyright Laws and the copyright laws of foreign countries, pursuant to the Universal Copyright Convention and the Berne convention.