™ OWNER'S MANUAL MODEL NO. 45-03083 Universal Tow Behind Tiller CAUTION: Read Rules for Safe Operation and Instructions Carefully • • • • • Assembly Operation Customer Responsibilities Service and Adjustment Repair Parts the fastest way to purchase parts www.speedepart.com Printed in U.S.A. FORM NO.
TABLE OF CONTENTS SERVICE AND ADJUSTMENT.............................11-12 STORAGE.................................................................. 12 TROUBLESHOOTING................................................ 13 REPAIR PARTS.....................................................14-16 PARTS ORDERING/SERVICE.....................Rear Cover SAFETY RULES........................................................... 3 ASSEMBLY................................................................4-5 OPERATION........
ASSEMBLY TO REMOVE UNIT FROM CARTON TO INSTALL THE TILLER GAUGE WHEELS • • • • • • • Cut from top to bottom all four corners of the carton and lay panels flat. (See Fig. 1) Remove the lag screw that holds the floating hitch to the packing skid. Disassemble and discard carton's wood top and side supports. Remove four hex bolt, hex nuts and flat washer from the hold down brackets at the rear of the carton. Remove and save the two Flat Washers and Cotter Pins from the rear axle.
ASSEMBLY TO INSTALL (WHEEL) WEIGHTS TO TILLER NOTE: Weights are not furnished with the Tiller. 30 lb. tractor wheel weights may be purchased to mount to the Tiller if extra weight is required. (Refer to the Operation section of this manual.) • Remove two Carriage Bolts and Nuts from each Tine Shield, located approximately 3-1/2" from the front edge. See fig. 4. • Place (Wheel) Weights on Tine Shield and secure with long Bolts and Nuts furnished with the Weights. See fig. 4. FIG.
OPERATION FIG.
OPERATION The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over the spectacles or standard safety glasses. HOW TO USE YOUR TILLER • BEFORE STARTING YOUR TILLER • FILL THE ENGINE WITH OIL! Your tiller engine is shipped without oil or gasoline. Add oil and gas as instructed in the separate engine manual.
OPERATION TRANSPORTING YOUR TILLER AROUND THE YARD • Pull forward on lift handle until it locks in the up, transport position. AROUND TOWN • Disconnect spark plug wire. • Drain fuel tank. • Transport in upright position to prevent oil leakage.
CUSTOMER RESPONSIBILITIES Check Engine Oil Level t5 Firs fore Be Fill in dates as you complete regular service. eac MAINTENANCE SCHEDULE to 8 hrs 25 . eve hrs. ry s or eas 50 on h eve rs. ry s or eas on 1 ev0e0 hrs ry s . or eas on Yea rly hu se Refer to the engine manual for instructions on engine maintenance.
CUSTOMER RESPONSIBILITIES ENGINE MAINTENANCE WARNING: Always stop engine and disconnect spark plug wire before cleaning, lubricating or before performing any repairs or maintenance. • • • • Check oil level before each use and every 8 hours. Maintain engine oil as instructed in the separate engine manual. Service air cleaner every 25 hours under normal conditions. Clean every few hours under extremely dusty conditions.
SERVICE AND ADJUSTMENTS WARNING: Shut off (disengage) the Tine Clutch Lever, the Tiller Engine and the Tractor Engine before making any repairs. TO REPLACE V-BELT Replace V-belt if it has been damaged considerably from slipping under heavy loads or if it show cracks or frayed edges. Refer to figures 11 and 12. IMPORTANT: Do not move or remove the belt guide. If the position of the belt guide is accidentally altered, return it to the correct setting (6-1/2" above the tine shield support plate).
SERVICE AND ADJUSTMENTS SPARE TINE DRIVE BOLTS WARNING: Shut off (disengage) the Tine Clutch Lever, the Tiller Engine and the Tractor Engine before making any repairs. • The Tiller drive components are protected from damage by (shearable) Grade 5 hex bolts in the Tine Assemblies. The hex bolts drive the tines and hold them in the proper location. Should the Tine Assemblies strike or pick up a large hidden object or become jammed, the hex bolts will break and the drive components will not be damaged.
TROUBLESHOOTING Follow the instructions in the "Service & Storage" section of the Engine Manual when performing any work on the Engine.
68 23 64 53 14 69 18 20 12 85 58 19 16 17 42 11 22 19 28 48 A 40 59 B A C 27 60 82 38 37 41 28 23 34 33 38 39 30 74 76 21 23 57 26 13 25 60 10 72 86 35 36 11 61 60 9 24 75 B 45 23 38 78 8 75 29 63 38 7 14 77 32 80 28 47 46 31 6 15 2 50 28 D 75 54 38 65 63 51 28 C 5 4 84 D 1 66 44 67 54 60 61 71 3 49 71 28 28 23 56 70 62 60 73 68 52 83 67 50 23 55 81 43 80 REPAIR PARTS FOR MODEL 45-03083 Unive
REPAIR PARTS FOR MODEL 45-03083 Universal Tow Behind Tiller ref. part no. qty. description ref. part no. qty.
REPAIR PARTS FOR MODEL 45-03083 Universal Tow Behind Tiller ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 part no. HA20344 43064 HA20123 HA20122 43013 HA20120 HA20136 HA20127 HA20121 43866 HA20125 HA20124 HA20130 HA20129 HA20132 HA20128 HA20133 HA20131 HA20135 43012 HA20137 HA20145 HA20155 HA20138 qty.
NOTES 17
NOTES 18
NOTES 19
the fastest way to purchase parts www.speedepart.com © 2001 Agri-Fab, Inc. REPAIR PARTS Agri-Fab, Inc. 809 South Hamilton Sullivan, IL. 61951 217-728-8388 www.agri-fab.