LCD Tablet Monitor User’s Manual 19 Inch wide 20 Inch wide 22 Inch wide 1
IMPORTANT SAFEGUARDS 1. Read all of these instructions. 2. Save these instructions for later use. 3. Unplug this monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use attachments not recommended by the monitor manufacturer as they may cause hazards. 5. Do not use this monitor near water, e.g., near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. 6.
FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
CONTENTS Introduction Product Features ................................................................. 5 Package Overview................................................................ 6 Installation Display Overview ....................................................................... 7 Connecting the Display ............................................................. 8 Operation & Adjustment Front Panel Controls................................................................... 9 KEY PROCESS .....
Introduction PRODUCT FEATURES • The monitor is designed for Pen-Input. • The convenient and user-friendly on-screen display allows for easy and accurate adjustments of screen size, position and screen color. • The monitor complies with the VESA Display Data Channel (DDC) specification for Plug and Play compatibility. Advanced microcircuitry makes setup and configuration fast and effortless.
Package Overview This manual explains how to correctly install, operate and get the best performance from your monitor. Please read this user’s guide carefully before installing your monitor, then keep it near your monitor for quick reference. LCD Tablet Monitor Application Software (Pen-InputDriver) Application Software (eduplus 5.
Installation Display Overview • Front View LCD Display Panel Controls • Rear View Stand 7
Connecting the Display To setup this display, please refer to the following figure and procedures. ⑤ USB ③ VGA ① Power ④ Audio-in (option) ② DVI-D (option) 1. Be sure all equipments are off. 2. Connect one end of the power adapter to the power connector; plug one end of the AC power cord into the power adapter, and then the other end into an electrical outlet (①). 3. Connect the VGA signal cable to the 15-pin connector of your host computer and tighten the screws (③). 4.
OPERATIION & ADJJUSTMENT Front Panel Controls 1. POWER Indicator 2. POWER Shows both normal operation Switches the monitor on and off. and power management status with power indicator light.. 3 (*) 4 (*) Moves cursor to the right or low window in the OSD window and increases the value of any selected function. While the OSD screen is off, you can adjust the brightness directly. Moves cursor to the left or high window in the OSD window and decreases value of any selected function.
KEY PROCESS COLOR BRIGHTNESS SELECT PICTURE CONTRAST FUNCTION COLOR TEMP. OSD MENU LANGUAGE MENU SOUND SELECT MENU MENU OSD OFF * Sound icon will be displayed only for Built in speaker model. BRIGHTNESS CONTRAST COLOR TEMP.
HOT KEY ◈ ◈ ◈ When there is no OSD, if you press this AUTO button, you can use the best display performance fit for a current mode. When there is no OSD, if you press this BRIGHTNESS button, you can adjust the brightness directly. ◀: decreases brightness ▶: increases brightness The screen will be brightened progressively by 10%. If you carry out general PC works such as document edition on the Movie mode,you may shorten the life span of LCD panel.
ADJUSTMENT PROCEDURE Perform the Auto tracking NO Is the H.SIZE proper? Adjust the CLOCK control. YES Perform the AUTO POSITION. Is the noise displayed on the screen? YES NO Adjust the CLOCK FINE until the screen is cleared.
OSD FUNCTIONS WITH USING PC BRIGHTNESS Adjust the brightness of image.. CONTRAST Adjust the contrast of image, the difference between light and dark areas on the screen. COLOR TEMP. Choose different preset color temperatures or set your own customized color parameters. H. POSITION & V. POSITION CLOCK PHASE Adjust the position of the display horizontally (left or right) and vertically (up or down). Adjust the width (horizontal size) of the screen image.
OSD H & V POSITION Adjust the OSD position horizontally (left or right) and vertically (up or down). OSD TIME Adjust the display OSD Menu. TRANSLUCENT Adjust the OSD. Transparency. LANGUAGE Select language for OSD MUTE Turn the audio sound on or off. VOLUME Increase or decrease audio volume.
SELF DIAGNOSIS If there is no image, the Self Diagnosis screen will be displayed. Self Diagnosis function checks if the status of the monitor screen is No Signal, Out of range or None support. No Signal screen is displayed when the DSub signal connector is connected but the status of the monitor is on DPMS mode. Out of Range screen is displayed when the applied frequency is under or over normal range.
SPECIFICATIONS Size Panel Type Pixel Pitch Viewing Angle Panel Contrast Ratio Brightness Response Time Color Filter Horizontal Synchronization Vertical Video Bandwidth Max Resolution Optima Colors Display Area Sync PC Input Signal Video Speaker Max. Output Special features Display screen PLUG & PLAY Power Source Power Consumption Dimension-W x H x D Weight-net/gross Power Saving Operating Temperature Technology Resolution Pressure Sensitivity Accuracy Max.
SPECIFICATIONS Size Panel Type Pixel Pitch Viewing Angle Panel Contrast Ratio Brightness Response Time Color Filter Horizontal Synchronization Vertical Video Bandwidth Max Resolution Optima Colors Display Area Sync PC Input Signal Video Speaker Max. Output Special features Display screen PLUG & PLAY Power Source Power Consumption Dimension-W x H x D Weight-net/gross Power Saving Operating Temperature Technology Resolution Pressure Sensitivity Accuracy Max.
SPECIFICATIONS Size Panel Type Pixel Pitch Viewing Angle Panel Contrast Ratio Brightness Response Time Color Filter Horizontal Synchronization Vertical Video Bandwidth Max Resolution Optima Colors Display Area Sync PC Input Signal Video Speaker Max. Output Special features Display screen PLUG & PLAY Power Source Power Consumption Dimension-W x H x D Weight-net/gross Power Saving Operating Temperature Technology Resolution Pressure Sensitivity Accuracy Max.
•The specification can be changed without any prior notice to improve the quality of the product. •The LCD panel may have some defective pixels (e.g. slightly light or dark) due to a characteristic of the LCD panel. But there is no defect in your LCD product itself.
FACTORY PRESET TIIMIINGS •The LCD Monitor has only Non-interlanced modes without flicker. VESA MODES Mode Resolution (dots Xlines) H.Freq(KHz) V.Freq(Hz) Remark VGA 640 X 480@60Hz 31.5 60 Non-interlaced VGA 640 X 480@72Hz 37.9 72 Non-interlaced VGA 640 X 480@75Hz 37.5 75 Non-interlaced SVGA 800 X 600@56Hz 35.2 56 Non-interlaced SVGA 800 X 600@60Hz 37.9 60 Non-interlaced SVGA 800 X 600@72Hz 48.1 72 Non-interlaced SVGA 800 X 600@75Hz 46.
Display Dimensions 19INCH 321 383 Front View Side View 65 178.
Display Dimensions 20INCH 321 383 Front View Side View 65 178.
Display Dimensions 22INCH 358 427 Front View Side View 66 178.
TROUBLESHOOTIING Symptom Check Picture is jitterd. Adjust Clock to set the screen position and adjust Clock fine until a noise isn’t displayed. No picture. Check if power switch and computer power switch are in the on position. Check if the signal cable is correctly connected to the video card. Check if the pins of D subconnector are not bent. Check if the computer is in the power- saving mode. POWER LED is not lit. Check if power switch is in the on position.
Pen-Input Driver&Software Installation The driver are located on the enclosed CD-ROM for the these operating systems: Windows Me/2000/98/XP , Mac 9.0/9.1/9.2. Pen-Input Driver & Software Installation Process: 1. Before your start to install the tablet driver, please be sure the USB cable already connected to the PC and LCD display. 2. Insert “Application software” CD-ROM. 3. Select “AHA USB Tablet Manager”. 4. Click “Next” button to make sure installing this driver 5. Click “Finish” button. 6.
24.Click “Next” button to make sure installing this program 25.Click “Accept” button 26.Click “Next” button 27.Click “Yes” button 28.Click “Install” button 29.Click “Finish” button 30. Restart the system. Pen-Input Setting and Calibration: 1. Open "Control Panel" of the system. 2. Double click "USB Tablet" icon. 3. Select the item you want to set up and change the setting values. These setting change are effective when these setting have been changed. Pen-Input Usage Notice: 1.
