User Manual

ManualsBrandsAigital ManualsOtherAIGITAL WIFI amplifier Router Xiaomi Pro-300MB

User Manual

This Mini router supports

Repeater Mode, AP Mode & Router Mode.

Here we have detailed setup instructions for you.

❀ How to Set Up Repeater Mode:

1. Plug device into socket. Wait for about 1 minute to establish a signal till you see

the green light blinking stably.

2. Please connect the wifi signal "Wireless-N" on your phone/laptop/computer(NOT

your home existing wifi, no need passwords)

3. Open your browser and enter 192.168.10.253 on address bar (Click “go”, NOT in

search bar, NOT add www.)

4. Log in. Username and password are both "admin".

5. Click on "Repeater" (under Wizard) to continue.

6. Select your home existing wifi name (the one you want to extend) and click

"Apply".

7. Change the Repeater SSID (NOT same as your home wifi name).

Type in your home wifi passwords as the Security key.(The security key must be

same as your home wifi password)

8. Wait and done. Reconnect to the new wifi and get access into the internet.

Quick Setup Video: https://youtu.be/hAmWoAfsn0o

OR: https://www.amazon.com/dp/B07HQ3KQY1?ref=cp_d_n_mn

Check it out Step by Step:

1. Please check you have plugged the device into power and lights are on and blinks

-- That means the device is working;

2. Please search the wifi signal "Wireless-N"on your phone/computer and connect it.

-- You need to connect the wifi first. If you cannot find the wifi signal, please unplug

and plug it to search again. If still no signal, please reset the device (Press the reset

button over 10s till only the power light on and WPS light on and then the WLAN

light blinks, You will see the lights changing from off to on again, that means you

reset the device successfully. -wireless-n becomes an open wifi)

Summary of content (4 pages)

PAGE 1
User Manual This Mini router supports Repeater Mode, AP Mode & Router Mode. Here we have detailed setup instructions for you. ❀ How to Set Up Repeater Mode: 1. Plug device into socket. Wait for about 1 minute to establish a signal till you see the green light blinking stably. 2. Please connect the wifi signal "Wireless-N" on your phone/laptop/computer(NOT your home existing wifi, no need passwords) 3. Open your browser and enter 192.168.10.253 on address bar (Click “go”, NOT in search bar, NOT add www.
PAGE 2
3. After you connected the wifi signal, please open your browser and enter the IP address 192.168.10.253 in the URL bar not search bar. -- Please kindly make sure the IP address is correct.And please don't add www.in front of the IP address. 4. Fill out the user name and password both "admin" on the webpage and continue. 5. Choose "Repeater" mode to continue. 6. Select and click your home wifi name. 7. You can change your SSID to anything but not same as your original home wifi name.
PAGE 3
Network Cable/Ethernet Cable from the wall and the LAN port is to your computer (If you need to use Ethernet cable) QUESTION: Why set the repeater mode unsuccessfully? ANSWER: 1) You may have typed in an incorrect password. Please reset it and try to re-configure it. 2) The device may be out of range, please move it closer to your router.
PAGE 4
❀ How to set up Router Mode: 1. Plug device into socket. Wait for about 1 minute to establish a signal till you see the green light blinking stably. 2. Connect this device (from WAN port) with your modem or router via Ethernet Cable. Search "Wireless-N" on your phone/laptop and connect it (No need passwords). 3. Open you browser and type in IP address “192.168.10.253” on the address bar, click “go”, not search, not add www. 4. Type in “admin” as the username and passwords to log in. 5.