User Manual

Product Diagram
AIHOOR C1
USER MANUAL
1. Volume up button
2. Volume down button
3. Mute button with LED
4. Multi-function button
5. Power button
6. Power LED
7. USB-C Input port
Using Your Product
1. Powering on/off
Press and hold the power button for 2 seconds to power on or off.
2. Connecting
a) Connect to your device using a USB cable.
4. Charging
Please charge this product for at least 1 hour before first use.
3. Button Controls
b) Connect to your device via Bluetooth.
It will automatically enter Bluetooth pairing mode when powered
on for the first time.
When this product enters pairing mode, the mute button LED will
flash blue. When this product is connected to a host device, the
mute button LED indicates the following status:
This product contains a lithium battery. Please do not disassemble,
strike, crush, or place the product into contact with flames. Do not
expose to high temperatures or direct sunlight for a prolonged
period. If there is any swelling, leakage, odor, or any other
abnormality in the battery compartment of the product, cease use
immediately. Please dispose of used batteries properly and in
accordance with local regulations.
Each time this product is powered on, it will automatically
pair with the last connected device if available.
This product will power off if no connection is made during
the 5-minute long pairing mode.
This product will being recharged once connected to a PC.
In Bluetooth mode, this product will terminate the connection
and shut down after 1 hour of inactivity.
If a disconnection takes place, this product will re-connect
to the last connected device. If no connection is made in 5
minutes, it will enter the pairing mode.
Specifications are subject to change without notice.
•
•
•
•
•
•
*To disconnect and reentering pairing mode, double press the
power button. To switch between Bluetooth and wired connection,
press and hold the multi-function button for 2 seconds.
+/
Press
Press and hold
Press
Press and hold
Press twice
Press
Volume up / down
Next / Previous track
Answer a call
Play / Pause music
End / Reject a call
Activate voice assistant of the
host device
Mute / Enable the microphone
Power LED Status
Solid red
Off
Charging
Fully charged
Specifications
Model
DC input
Battery capacity
Charging time
Fast charging
Playtime
Driver size
Microphone
Frequency response
Bluetooth version
Bluetooth protocols
Bluetooth range
AIHOOR C1
5V 2A
2500mAh
2 hours
15 min for 2-hour playtime
8 hours
2 x 40mm/1.57’’
2 x MEMS mic
180Hz - 16kHz
5.0
HSP/HFP/A2DP/AVRCP/SBC
60m/196ft
Mute Button LED Status
Notes
Read all instructions before use and save these instructions
for future reference.
Extreme temperatures will cause the device to deform.
Use electronic equipment with caution during thunderstorms.
Make sure to use an appropriate level of volume.
Keep out of the reach of children.
•
•
•
•
•
Safety Instructions
Battery Warning
Mic on
Mic off
Playing music
Music paused
Solid blue
Solid red
Flashing blue
Solid blue
Warranty & Customer Support
ON
ON
- 01 - - 02 - - 03 -
- 04 - - 05 - - 06 -
For questions, support, or warranty claims, contact us at the
address www.aihoor.net that corresponds with your region. Please
include your Amazon order number and product model number.
Thank you for purchasing the AIHOOR C1 Bluetooth
Speakerphone. Please read this user manual carefully and keep it
for future reference. If you need any assistance, please contact our
support team with your product model number and Amazon order
number.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be
used in portable exposure condition without restriction.