TYPE：TE001-Upgrade E-bidet USER MANUAL
Contents Use precautions 4 Component description 5 Installation steps 6 Product description 8 Function introduction 9 Cleaning and maintenance 13 Product dimension drawing Product technical specification Warranty Card 15 17 18 19 Other matters Faults and solutions Installation and use 1 Before use Safety notes
Safety notes Read the safety instructions carefully before use so as to properly use the product. Note the following warnings relevant to the safety. Warning Prohibition Compulsory observance Note Failure to operate pursuant to the above-mentioned warning signs may result in injury or life-threatening risk. People (including children) who are deficient in body, perception, intellectual capacity, or experience and common sense (including children) are cognized.
Safety notes Only suitable for the power in technical specification;It is strictly prohibited to use excessive loads on the same socket. May result in overheating or fire. Ensure that the water,cleaning agent or urine does not wet the power plug. May result in fire or electric shock. 2 Do not pull the power plug/ power cord at will. May result in fire or electric shock. Do not use a loose socket. May result in fire or electricshock.
Safety notes Do not disassemble, repair and modify products by without authorization. May result in fire or electric shock. Please unplug the power supply when cleaning the product. May result in electric shock. 3 Please don't keep the lighted cigarette or other combustion items near the product Do not bend or twist the water supply hose. May result in water leakage. May result in fire. Do not place heavy objects on the toilet seat or the toilet cover May result product damage. Do not invert product.
Use precautions Do not place this product in direct sunlight. The room temperature of toilet shall be above 0°C. It may cause product discoloration and failure of seat heating function. Otherwise, it is possible to freeze the product. Use warm air and other methods to improve the temperature in the toilet. Please not use substandard power supply. Do not shower urine on the bidet body and nozzle. May cause product failure. May result in blockage.
Component description 1.Cover plate 2. Installation template 3.Fixation part bolt (2) sheet (2) Plastic TAB(2) Fixing plate Rubber bushing(2) 5 4.T-junction 5. Water inlet hose 6.
Installation steps Installation tools Cross screwdriver Monkey wrench Barrel and rag Attention before installation 1.Water pressure range: 0.1-0.75MPa, please follow the instructions. 2.Corner valves shall be located close to the location where this product is installed and disassembled. 3.Please use the braided hose that comes with the product to prevent water leakage. 4.When installing braided hose,be careful to prevent the black gasket falling out. Installation Procedure 1.
Installation steps 6.Close the water valve； 7.Install braided hose； We suggest connecting the elbow end of the hose to the cover 8.Installation tee； 9.Open the angle vavle to check water leakage； inlet valve tee 2 hose hose 7 angle valve 10.Turn on the knob to check whether the nozzle is protruding； Note Prohibition 11.Plugged into a power supply； Inoder to protect the internal circuit,be sure to turn on the nob to make the nozzle out before plugged into power 1.
Product description Toilet cover Toilet seat Nozzle Knob Water supply hose joint 8 Power socket Drain plug Disassembly button (Reset button) Temp.
Function introduction-Type 111 Standby mode 1.After the power supply is connected, the “bi” indicates that the cover can be used normally. 2.Water temperature by default at low gear: about 35℃. 3.Seat temperature by default at low gear: about 33℃. Rinsing function 1.Bidet/Hip Rinsing Bidet After sitting down, there is a beep prompt, rotating the knob to start rinsing Hip 2.
Function introduction-Type 111 Description of function Function setting key Lighting Lighting Tip OFF Water temp. control key LOW HIGH Seat temp. control key Repeatedly press will switch over water temperature in the sequence indicated in the left figure. OFF Change water temp.:a short sound. Turn off water temp.:a long sound. High Low low: about 35℃. high: about 38℃. Repeatedly press will switch over water temperature in the sequence indicated in the left figure. OFF Change seat temp.
Function introduction-Type 112 Standby mode 1.After the power supply is connected, the “bi” indicates that the cover can be used normally. 2.Water temperature by default at low gear: about 35℃. 3.Seat temperature by default at low gear: about 33℃. Rinsing function 1.Bidet/Hip Rinsing Bidet After sitting down, there is a beep prompt, rotating the knob to start rinsing Hip 2.
Function introduction-Type 112 Description of function Function setting key Lighting Lighting TIP OFF Water/wind temp. setting key OFF LOW HIGH Seat temp. setting key Repeatedly press will switch over water temp. in the sequence indicated in the left figure. Change water temp. :a short sound. Turn off water temp. :a long sound. HIGH LOW Repeatedly press will switch over wind temp. in the sequence indicated in the left figure. LOW HIGH MID OFF HIGH low : about 35℃. high : about 38℃.
Cleaning and maintenance Manual cleaning of spray tube - Gently pull out the nozzle and dip the neutral detergent with a soft cloth, sponge or small brush. - Gently support the nozzle, wipe the spray tube and nozzle. Clean filter screen 2 Braided hose A A Filter screen Tips: - Make sure that the corner valve close and the power off before you clean the filter screen； - Clean the filter screen when the water flow is less than normal hours.
Cleaning and maintenance Product maintenance in winter when the temperature of toilet below 0℃： -Pull out the power plug . -Remove water inlet hose from the angle valve to the toilet end, and empty the water in the water inlet hose; -Remove the bottom nut,and drain internal water. Not use in a long time When this product is not used for a long time, drain the water in the product and cut off the power supply: - Pull out the power plug . - Close angle valve and stop the water inlet.
Faults and solutions Common fault diagnosis When you think it is a fault, try some of the following processing methods. If the product is still not working properly, contact your local repair center or call the service hotline. Check power supply Check water supply 1.If power supply is under normal state. 2.If leakage protector trips 3.Mannual reset thermostat(Istallation step4) 1.If water supply is under normal state. 2.If corner valve is closed.
Product dimension drawing Failure analysis of seat Phenomenon The seat is cold Possible cause The seat heating is turned off The product started the Temperature drops low temperature scald When rinsing prevention function Solution Turn on the heating function in advance After cleaning, the setting temperature will rise again Failure analysis of light Phenomenon Solution Possible cause Night light is not ON.
Product dimension drawing Product dimension drawing V-shape 370 132-178 202 374 434-490 300 508 85 size: mm 17
Product technical specification Items Description Rated voltage 120V~, 60Hz Rated power 1050W Max. transient power 1450W Length of power line About 1.1m Water supply pressure 0.1 ~ 0.75MPa(Static pressure) Water supply temperature 5 ~ 35℃ Ambient temperature 0 ~ 40℃ Net weight About 3.
Warranty Card To dear customers: Thank you for choosing our E-bidet! If any problem occurs during use, please simply remove and check the problems pursuant to the user's manual. When you cannot remove such problems, contact your local supplier or call the service hotline. I. Information: Customer information Customer name Address TEL Dealer information Name TEL Model Purchase date Y M D Product series number Warranty Two-year free warranty since period the purchase date II.
