AiM User Guide Kit for EVO4, Solo and SoloDL on Ducati 899,1199 Panigale Release 1.
1 Models and years This user guide explains how to install AiM Solo and SoloDL on Ducati Panigale bikes and how to connect EVO4 and SoloDL to the bike Engine Control Unit (ECU).
2.1 Kit and bracket for Solo/SoloDL on Ducati Panigale Solo/SoloDL installation kit is shown here below; part number is: V02569170CSP. The kit includes: • 1 bracket (1) • 2 4x10 Allen screws with countersunk head (2) • 1 washer(3) • 1 rubber distance piece (4) • 1 8x45 pan head Allen screw (5) • 1 AiM ECU interface cable for Ducati Panigale (6) AiM cable (6) and bracket (1) can also be bought separately as spare parts.
2.2 AiM cable for SoloDL AiM cable for SoloDL on Ducati bikes is shown below; its part number is: V02569170.
2.3 AiM cable for EVO4 AiM cable for EVO4 on Ducati bikes is shown below; its part number is: V02563150.
3 Installation and connection Here you find the instructions to install Solo and SoloDL on Ducati Panigale and to connect EVO4 and SoloDL to the bike ECU. EVO4 cable length allows installation of the logger under the bike seat. 3.1 Installation of Solo and SoloDL To install Solo/SoloDL on your Ducati bike: Place the washer and the rubber distance piece in line with Panigale bracket hole and insert M8 screw tightening all pieces.
Insert the assembled brackets in the handle bar hole. Tighten the M8 screw and the distance piece until the assembled brackets about the bike fork. Hook Solo to its bracket. Tighten Solo bracket screws.
3.2 Connection of SoloDL and EVO4 to the bike ECU To connect EVO4 and SoloDL to the ECU of the bike use the connector you find under the passenger seat. Open the bike tail and remove the connector cup highlighted in the image here on the right. Once the cup has been removed the connector appears as here on the right.
Connect AiM wiring to Ducati wiring as here on the right. Take the cable to the logger as here on the right. To reach SoloDL make the cable pass between the fuel tank and the bike frame. Please avoid positions where the cable would be exposed to direct heat.
The image here on the right shows the cable reaching SoloDL. Connect the cable to SoloDL as here on the right.
4 Configuring with Race Studio 2 Before connecting EVO4/SoloDL to the ECU it is necessary to set it via Race Studio 2 software. 4.1 Configuring SoloDL Run the software, press “Device Configuration” on the software left keyboard and select “SoloDL” in the panel that shows up as below.
The software shows SoloDL configuration page: press “Configuration Manager” and select the configuration you want to use or press “New” to create a new one. In this second case “New Configuration” panel appears.
Confirm pressing “OK” in both panels and transmit the configuration to SoloDL pressing “Transmit” as shown below. 4.2 Configuring EVO4 Run the software, press “Device configuration” on the software left keyboard and select “EVO4” in the panel that shows up on the right as here below.
The software shows EVO4 configuration page: select the configuration you want to use or press “New” to create a new one. In this second case “New Configuration” panel appears: select: • ECU Manufacturer: • ECU Model: Ducati Panigale Press “OK” and transmit the configuration to SoloDL pressing “Transmit” as shown below.
5 Ducati protocols Channels received by SoloDL and EVO4 connected to Ducati Panigale protocol are: ID CHANNEL NAME FUNCTION ECU_1 ECU_RPM RPM ECU_2 ECU_SPD_REAR Rear wheel speed ECU_3 ECU_TPS1_ENG Throttle position cylinder 1 ECU_4 ECU_TPS2_ENG Throttle position cylinder 2 ECU_5 ECU_TPS_HAND Manual throttle ECU_6 ECU_WATER_T Engine coolant temperature ECU_7 ECU_SPD_FRONT Front wheel speed ECU_8 ECU_INT_AIR_TEMP Intake air temperature ECU_9 ECU_BATTERY Battery supply ECU_10 EC
ECU_25 ECU_DIAG_V Vertical cylinder lambda diagnosis ECU_26 ECU_BRK_FRONT Front brake pressure ECU_27 ECU_BRK_REAR Rear brake pressure ECU_28 ECU_DTC_RDC Ducati traction control intervention ECU_29 ECU_DTC_PERC Ducati traction control percentage 15
