AiM User Guide Kit for EVO4, Solo and SoloDL on Ducati 848, 1098, 1198 Release 1.
1 Models and years This user guide explains how to install AiM Solo and SoloDL on Ducati bikes and how to connect EVO4 and SoloDL to the bike Engine Control Unit (ECU).
2.1 Kit and bracket for Solo/SoloDL Solo/SoloDL installation kit is shown here below; part number is: V02569170CS. The kit includes: • 1 bracket (1) • 2 4x10 Allen screws with countersunk head (2) • 2 M4 self locking nut (3) • 1 AiM interface cable for Ducati 848/1098/1198 (4) AiM cable (4) and bracket (1) can also be bought separately as spare parts.
2.2 AiM cable for SoloDL AiM cable for SoloDL on Ducati bikes is shown below; its part number is: V02569170.
2.3 AiM cable for EVO4 AiM cable for EVO4 on Ducati bikes is shown below; its part number is: V02563150.
3 Installation and connection Here you find the instructions to install Solo and SoloDL on your Ducati bike and to connect EVO4 and SoloDL to the bike ECU. EVO4 cable is long enough to allow installation of the logger under the bike seat. 3.1 Installation of Solo and SoloDL To install Solo/SoloDL on your Ducati bike: Fix AiM bracket for Ducati to Solo bracket using the two Allen screws you find in the kit. Remove the steering wheel dumper starting with the Uniball screw highlighted here on the right.
Remove the screw of the steering wheel dumper collar enlarging the collar. Slide off the stem of the steering wheel dumper. Remove the screw that locks the collar to the steering plate and remove the collar from the bike. Hook AiM bracket for Ducati rotating it as in the image.
Replace the steering wheel dumper collar using the proper screw and locking AiM bracket for Ducati between collar and fork plate. Replace the stem in the collar re-screwing its screws and replace Uniball screw fixing it to the frame pivot. Hook Solo to its housing.
3.2 Connection of SoloDL and EVO4 to the bike ECU To connect EVO4 and SoloDL to the ECU of the bike use the connector you find under the passenger seat. Open the bike tail and remove the connector cup highlighted in the image here on the right. Once the cup has been removed the connector appears as here on the right.
Connect AiM wiring to Ducati wiring as here on the right. Take the cable to the logger as here on the right. To reach SoloDL make the cable pass between the fuel tank and the bike frame. Please avoid positions where the cable would be exposed to direct heat.
The image here on the right shows the cable reaching SoloDL. Connect the cable to SoloDL as here on the right.
4 Configuring with Race Studio 2 Before connecting EVO4/SoloDL to the ECU set it up via Race Studio 2 software. 4.1 Configuring SoloDL Run the software, press “Device Configuration” on the software left keyboard and select “SoloDL” in the panel that shows up as below.
The software shows SoloDL configuration page: press “Configuration Manager” and select the configuration you want to use or press “New” to create a new one. In this second case “New Configuration” panel appears: select • ECU Manufacturer: “DUCATI” • ECU model: “1098/S” Confirm pressing “OK” in both panels and transmit the configuration to SoloDL pressing “Transmit” as shown below.
4.2 Configuring EVO4 Run the software, press “Device configuration” on the software left keyboard and select “EVO4” in the panel that shows up on the right as here below.
The software shows EVO4 configuration page: select the configuration you want to use or press “New” to create a new one. In this second case “New Configuration” panel appears: select • ECU Manufacturer: “DUCATI” • ECU model: 1098S Press “OK” and transmit the configuration to EVO4 pressing “Transmit” as shown below.
5 Ducati protocols Channels received by SoloDL and EVO4 connected to Ducati "1098/S" protocol are: ID CHANNEL NAME FUNCTION ECU_1 DUCATI_RPM RPM ECU_2 DUCATI_SPEED Vehicle speed ECU_3 DUCATI_TPS Throttle position ECU_4 DUCATI_ECT Engine coolant temperature ECU_5 DUCATI_AIRTEMP Intake air temperature 15
