User's Manual

ManualsBrandsAimpoint ManualsFirearm AccessoriesCompM4

4 AIMPOINT

SPACERS

4.1 Standard spacer

Height of the optical axis (from the top of the rail) when using a standard

spacer is 39 mm (1.5") for CompM4 and CompM4s.

Technical specification

Weight 25 g / 0.9 oz

Height of optical axis with spacer 39 mm / 1.5"

Length 70 mm / 2.8"

Width 21 mm / 0.8"

4.2 Extension spacer

Height of the optical axis (from the top of the rail) when using an extension

spacer is 39 mm (1.5") for CompM4 and CompM4s. The extension spacer

moves the position of the sight by 40 mm / 1.6".

Technical specification

Weight 45 g / 1.6 oz

Height of optical axis with extension spacer 39 mm / 1.5"

Length 110 mm / 4.3"

Width 21 mm / 0.8"

LRP mount, QRP2 / QRW2 mount and

TNP mount for CompM4™ / CompM4s™

User manual

Summary of content (8 pages)

PAGE 1
z " " " z " " " LRP mount, QRP2 / QRW2 mount and TNP mount for CompM4™ / CompM4s™ User manual
PAGE 2
1 PRESENTATION Aimpoint® CompM4 and CompM4s are designed to be mounted on a firearm with a MIL-STD 1913 Picatinny rail or Weaver rail. Height of optical axis can be adjusted by adding or removing a spacer to the configuration. 2 ASSEMBLE SIGHT, MOUNT AND SPACER 2.1 Sight and mount only Assemble the sight to the mount using two short screws. Tighten firmly. It is recommended to use thread sealer on the screw threads. Height of the optical axis (from the top of the rail) when not using a spacer is 30 mm (1.
PAGE 3
Mounting CompM4™ / CompM4s™ with LRP mount: 1 Lift the lever (2) up to release it and set to open. 2 Position the recoil stop (3) in a groove to be used on the rail and install the mount. See Fig. 1. CAUTION: Ensure that the groove to be used is clean and free from dirt. 3 With the recoil stop (3) positioned in a groove of the rail, push the sight with mount forward (toward muzzle) and close the lever (2) with the hand (no tools) until it clicks into the slot of the base. See Fig. 2.
PAGE 4
3.2 QRP2 / QRW2 mount for CompM4™ / CompM4s™ The QRP2 mount and QRW2 mount are quick detach mounts. The QRP2 is designed for mounting on a MIL-STD 1913 Picatinny rail and the QRW2 is designed for mounting on a Weaver rail. Technical specification Weight Height of optical axis (no spacer) Length Width 70 g / 2.5 oz 30 mm / 1.2" 70 mm / 2.8" 55 mm / 2.2" Mounting CompM4™ / CompM4s™ with QRP2 / QRW2 mount: 1 Loosen the torque knob (1) by turning it counter clockwise.
PAGE 5
Fig. 3 Fig. 4 3.3 TNP mount for CompM4™ / CompM4s™ The TNP mount mount is a fixed mount for mounting on a MIL-STD 1913 Picatinny rail. NOTE: Always perform zeroing if the sight with TNP mount is removed and re-mounted on the Picatinny rail. Technical specification Weight Height of optical axis (no spacer) Length Width 60 g / 2.1 oz 30 mm / 1.2" 70 mm / 2.8" 41 mm / 1.
PAGE 6
Mounting CompM4™ / CompM4s™ with TNP mount: 1 Loosen the torsion nuts (1) to release clamping force from the brackets (2) 1 Position the recoil stop (3) in a groove to be used on the rail and install the mount. See Fig. 5. CAUTION: Ensure that the groove to be used is clean and free from dirt. 2 With the recoil stop (3) positioned in a groove of the rail, push the sight with mount forward (toward muzzle) and tighten the two torsion nuts by hand until resistance is encountered.
PAGE 7
4 AIMPOINT® SPACERS 4.1 Standard spacer Height of the optical axis (from the top of the rail) when using a standard spacer is 39 mm (1.5") for CompM4 and CompM4s. Technical specification Weight Height of optical axis with spacer Length Width 25 g / 0.9 oz 39 mm / 1.5" 70 mm / 2.8" 21 mm / 0.8" 4.2 Extension spacer Height of the optical axis (from the top of the rail) when using an extension spacer is 39 mm (1.5") for CompM4 and CompM4s. The extension spacer moves the position of the sight by 40 mm / 1.
PAGE 8
Aimpoint AB Jägershillgatan 15 SE- 213 75 Malmö, Sweden Phone: +46 (0)40 671 50 20 Fax: +46 (0)40 21 92 38 e-mail: info@aimpoint.se WWW.AIMPOINT.COM © 2012, 2017 Aimpoint AB. [13510-1] Aimpoint Inc. 7309 Gateway Court Manassas, VA 20109, USA Phone: +1 703-263-9795 Fax: +1 703-263-9463 e-mail: info@aimpoint.