0207 A AI GHW-LC GH System Lift control adaptor GHW-LC -1- INSTALLATION & OPERATION MANUAL
1 SYSTEM CONFIGURATION System Configuration Wiring Distance 2 CONTENTS Contents 3 NAMES Names 4 MOUNTING Mounting 5 WIRING Wiring 6 SETTING UP Setup tool Lift Control 1 Lift Control 2 Data transfer Combine Data 7 OPERATIONS Residential Station or Security Guard Station Door Release Automatic Entry (Doctor Call) Option 8 TECHNICAL PRECAUTIONS Technical precautions 9 SPECIFICATIONS Specifications PRECAUTIONS General Prohibitions Prohibition to Dismantle the Unit Prohibition on Subjecting the Unit to Water
1 1-1 1-1 SYSTEM CONFIGURATION System Configuration a. GH expanded system (For details, see the GH Series Installation & Operation Manual.) Make sure to use GH-BCX/A, GH-DA/A, GH-NS.
2 3 CONTENTS NAMES [3] GHW-LC Contents Lift control adaptor GHW-LC (mounting bracket is included) [1] [3] [2] [4] Names [1] Bus line terminal [2] ID setting switch [3] Relay output terminal [4] Lock release lever -4-
4 MOUNTING [1] [1] GHW-LC [2] Mounting [1] Din rail [2] Lock release lever Mount GHW-LC to the Din rail. ∗ To remove GHW-LC, pull the lock release lever down. GHW-LC cannot be mounted directly to the wall surface.
5 WIRING [3] #8 RY1 1P NP RY20 1P NP GH-BCX/A 1P NP GHW-LC R1 R2 to Lift controller Max. 8 [3] #1 RY1 1P NP #9 to #16 (max.
Wiring a. GH expanded system (For details, see the GH Series Installation & Operation Manual.) [1] Expanded Bus control unit GH-BCX/A [2] Distribution terminal (junction): Not included [3] Lift control adaptor GHW-LC Maximum 16 adaptors (up to 8 adaptors per trunk) • ID: ID setting switch (factory setting is #1) Make sure to set corresponding ID number.
6 6-1 Setup tool ∗ Completing settings with the setup tool is required. 1. Install the setup tool in the PC (Windows XP/2000/ME ®) beforehand, and then enter the resident information. ∗ For details on the setup tool, refer to the GH Series Installation & Operation Manual. Save programmed data and resident information data to your PC is recommended. 2. Connect the PC terminal of GH-BCX/A to the PC with RS232C cable (included with GH-NS or GH-MK). ∗ PC requires serial output.
6-2 [1] 6-3 [2] [3] [4] [1] [5] [2] Lift Control 2 [1] The resident information that has been entered will be displayed. [2] Set which relay will activate in the corresponding GHW-LC for each residence. The setting range is "1 to 20". Lift Control 1 [1] GHW-LC ID [2] Select "ON" or "OFF" for the GHW-LC connection. [3] Select "N.O." or "N.C." for the Output Type. [4] Set the Timer. The time setting range is "1 to 600" sec.
6-5 7 7-1 1 OPERATIONS 1 1 G I K 3 L T 8 U V N F O W 9 X 0 E 6 M P S C 5 J R B D H 7 Y Z A 2 4 Q 2 2 Residential Station or Security Guard Station Door Release 1. Press the door release button at the residential station or security guard station while in communication with the entrance station that made a call. 2. The door release function will activate on the entrance station that is in communication, and the lift will begin to move.
8 9 TECHNICAL PRECAUTIONS Technical precautions • Operating temperature: 0 °C to 40 °C (32 °F to 104 °F) • Repair requests: When units do not operate properly, contact a qualified technician for service. SPECIFICATIONS Specifications • Power supply: Supplied by GH-BC • Relay contacts: 20 AC/DC 24 V, 500mA, N.O./N.C. dry closure operation time accuracy 2% • Wiring: single-pair cable • Type of cable: Pair cable (solid wire not stranded), polyethylene insulated, diameter 0.65 ~ 1.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
