FK1594 P1210AQ 53715 JKW-IP IP Video Intercom Adaptor JKW-IP IP Video Intercom Adaptor NE O PH AI 2 N LA W JK AC T ER W US PO AT ST -IP S1 TH Y E R 8V DC1 OFF N ER O POW LAN ENG IP L STR E S4 3 E E S S2 + - 1B RYB m 11m ∼ 0.65 1.
CONTENTS 1 INTRODUCTION .......................... 6 5 PC Application Basic Operations .. 39 1-1 System Configuration Example ....... 6 5-1 Video Intercom Functions ............. 39 1-2 Names ............................................ 7 5-1-1 Answering a call from the door station .. 39 IP Video Intercom Adaptor ..........................7 5-1-2 Door release .................................. 40 PC Application Window ...............................8 5-1-3 Zoom/Wide, Pan & Tilt ...................
PRECAUTIONS Warning and Caution General Prohibitions Prohibition to Dismantle the Unit WARNING Prohibition on Subjecting the Unit to Water General Precautions General Precautions Negligence could result in death or serious injury. 1. Keep the unit more than 1 m away from radio or TV set. 2. Keep the intercom wires at least 30 cm (12") away from AC 100-240 V lines. Noise and malfunction could result. 1. Do not dismantle or alter the unit. Fire or electric shock could result. 3.
Notes on Usage • The times for the master monitor station and the PC Application are not synchronized. • Lip-sync is not performed for audio and video in the PC Application. • Depending on the network environment and computer, it may not be useable. • There are times when audio and video may be delayed in the PC Application due to encoding, decoding, or the network.
Notices • We will under no conditions be liable for damage that occurs due to failures in network equipment; failures due to internet providers and cell phone companies; failures such as disconnected lines and other losses in communication, which render it impossible to provide this service or in any way delay this service due to causes outside of our responsibility; or if an error or missing data occurs during transmission.
INTRODUCTION 1 INTRODUCTION 1-1 System Configuration Example For Local IP Video Intercom Adaptor JKW-IP N.O. / N.C. Sensor input 1 Sensor input 2 + - E ON PH AI N LA T US ER W PO AT ST E S2 E S3 RY E RY E S4 B1 B2 R ON OFF POWE DC18V Master monitor station JK-1MED or JK-1MD Power supply PS18 PS-1820 m 11m 0.65 1.
INTRODUCTION 1-2 Names IP Video Intercom Adaptor DC18V OFF POWER ON Turns the power ON or OFF. POWER terminal (18V DC) Connects the power cable. Master monitor station connection terminal S1 E S2 E S3 E S4 E RY RY B1 B2 + - POWER switch Connects to the master monitor station. Option output terminal Connects output signals for option units. Sensor input 4 terminal Sensor input 3 terminal Sensor input 2 terminal LAN Sensor input 1 terminal Connects to buttons, sensors, etc. for option units.
INTRODUCTION PC Application Windows The PC Application window consists of a "Standard Window" and an "Expanded Window". You can switch between the Standard Window and the Expanded Window by clicking the [Standard window] or [Expand window] button. Standard Window In the Standard Window, you can perform the following setting operations. [SENSOR] display Displays the status of incoming signal(s) from option unit(s) P.
INTRODUCTION Expanded Window The following explains the various buttons in the Expanded Window and the display contents. The content on the left-hand side of the window is the same as the Standard Window.
INTRODUCTION 1-3 About System Settings MEMO M • Be sure to check the system configuration before making settings, and then connect the units correctly. • You need to contact your provider (ISP) to connect to the Internet. • Before making settings, be sure to obtain necessary information such as the Static IP Address, Email Addresses, and any other necessary information. * The factory default IP address setting of this device is 192.168.0.30.
INTRODUCTION STEP 2 1 Registration of the IP Video Intercom Adaptor by the Administrator 4 Installing the PC Application Install the PC Application onto the Administrator PC. Registration Configuring the IP Video Intercom Adaptor network Login to the IP Video Intercom Adaptor and configure the network environment. 1-5 Installing the PC Application P.12 3-2 Logging in P.20 3-3-5 Network Settings / Connection Settings P.
INTRODUCTION 1-4 Starting up the IP Video Intercom Adaptor Provisional registration Registration : Administrator/User Use the following steps to start up the IP Video Intercom Adaptor. 1. Check that the wires are connected correctly. 2. Turn on all connected equipment except for the IP Video Intercom Adaptor. 3. Turn on the POWER switch for the IP Video Intercom Adaptor. ・The POWER indicator (Green) and the LAN ACT indicator (Orange) light, and the STATUS indicator (Orange) blinks.
INTRODUCTION 1-5-2 Installing ・If ".NET Framework" is not already installed, the .NET This section describes how to install the PC Application into your PC. • The screens may differ depending on the OS. • Follow the on-screen instructions to install. Framework installation window is displayed. Follow the onscreen instructions to install. MEMO • When starting up the application, if a security or virus check warning is displayed, please allow the application to continue. 1.
INTRODUCTION 5. Click [Next]. 8. When the installation is complete, the Select Recording ・The Select Installation Folder window is displayed. File Storage Folder (Browse for Folder) window is displayed. 6. Click [Next]. 9. Select the folder where you want to save recorded files, ・The folder in which the application is to be installed is created. and then click [OK]. ・The selected folder becomes the storage location for recorded files. ・After it is selected, the saved location cannot be changed.
INTRODUCTION 1-5-3 Uninstalling From the Windows "start" menu, select "Control Panel" " "Add or Remove Programs", and select "Aiphone_JKW" to delete it. MEMO • With Windows 7, the PC Application may still remain on the taskbar after it is deleted. Delete the taskbar application separately. 1-5-4 Starting up the PC Application To start up the PC Application, double-click the " " icon on the desktop.
Network Settings 2 Network Settings 2-1 PC Network Settings Provisional registration Registration : Administrator/User 3. Enter the IP Address, Subnet Mask, and other necessary Set the IP Address, Subnet Mask, and other necessary information on the PC of the person setting up the network, the Administrator PC, and the User PCs, according to the network environment. information according to the network environment, then click [OK]. ・For provisional registration, enter "192.168.0.
Network Settings 2-2 Connecting the PC of the person setting up the network and the IP Video Intercom Adaptor Provisional registration In order to configure the IP Video Intercom Adaptor, use a LAN cable and connect the PC of the person setting up the network and the IP Video Intercom Adaptor. When connecting the PC of the person setting up the network directly to the IP Video Intercom Adaptor, use an Ethernet crossover cable. When connecting via a hub, use a straight cable.
IP Video Intercom Adaptor Settings 3 IP Video Intercom Adaptor Settings See "Settings List" P.50 for a list of the IP Video Intercom Adaptor settings. 3-1 Registering the IP Video Intercom Adaptor Provisional registration Registration : Administrator/User 3. Enter the unique IP Address, Connection Port, Connection To operate the IP Video Intercom Adaptor, you need to register the IP Video Intercom Adaptor connected to the system.
IP Video Intercom Adaptor Settings 4. Enter a valid ID and Password. ・If you enter the ID and Password here, you will not have to enter them again when logging into the IP Video Intercom Adaptor. ・For Global, it may be necessary to change ports when you are using multiple IP Video Intercom Adaptors or PC Applications. Please check our homepage at http://www. aiphone.net for more details.
IP Video Intercom Adaptor Settings 3-2 Logging in Provisional registration Registration : Administrator/User To modify IP Video Intercom Adaptor settings, you first need to login. MEMO • Since you are not registered as a User before setting up, you can only login as the Administrator. You can login as the "Administrator" or a "User". Setting items are restricted depending on which you use to login. Login using the following method. 1.
IP Video Intercom Adaptor Settings 3-3 Administrator Settings Provisional registration Various Administrator settings for the IP Video Intercom Adaptor can be made from the Administrator Settings window while logged in as the Administrator. 3-3-1 Administrator Registration In Ad minist rator Regist ration, you can change the Administrator ID and Administrator Password. The default settings are - Administrator ID: "aiphone" and Administrator Password: "aiphone".
IP Video Intercom Adaptor Settings 3. Enter a password in New Password. 3-3-2 User Registration ・You can enter up to 16 single-byte alphanumeric characters for the password. Registration : Administrator Users other than the Administrator can be registered to allow them to use the IP Video Intercom Adaptor. Enter the User ID and User Password in User Registration. MEMO • If you are logged in as a User, you cannot perform User Registration. 1.
IP Video Intercom Adaptor Settings 3. Click [SAVE]. 3-3-3 Email Setting (IP Video Intercom Adaptor) ・"[User Registration] Setting has been saved." is displayed, In Email Setting, you can set information on the origin of the sent Email. and you are returned to the Administrator Settings window. MEMO • If you are logged in as a User, you cannot perform Email Setting. • Prepare an Email account for the IP Video Intercom Adaptor beforehand. 1.
IP Video Intercom Adaptor Settings 3. Click [SAVE]. 3-3-4 Sensor input / Option output Settings ・"[Email] Set t i ng has been saved." is d isplayed, the In Sensor input / Option output Settings, you can set the Sensor input latch duration and detection method, and select the Option output signal output duration. Sensor input detects the N.C. contact input for "N.C." and detects the N.O. contact input for "N.O.". The factory default settings are – Input latch: "Continuous", Sensor input: "N.O.
IP Video Intercom Adaptor Settings 2. Select Input latch and Sensor IN settings between 1 and 3. Enter the Output Duration for Option OUT. 4 and make optional settings. *1 ・Set the Output Duration to between 0 and 600 seconds. ・When set to 0 seconds, it is only output when the "OPTION" *1 The following table shows the detection operation of sensor input if the input latch setting of the IP Video Intercom Adaptor is different from the sensor input settings of the master monitor station.
IP Video Intercom Adaptor Settings 3-3-5 Network Settings Connection Settings Provisional registration The following 5 settings come under Network Settings. You can change the Static IP Address setting for the IP Video Intercom Adaptor. The default settings are - IP Address: "192.168.0.30", Subnet Mask: "255.255.255.0", and Default Gateway: "192.168.0.30". • Connection Settings • Adaptor Name Settings Registration : Administrator • Adaptor Language Settings Contact your network Administrator, etc.
IP Video Intercom Adaptor Settings 3. Enter the "Connection Port" number, "Audio Port" Update Encryption Key File, Adaptor Name Settings, Adaptor Language Settings, Video Setting number, "Video Port" number, and "Web Port" number. ・The factory default setting numbers are - Connection Port: Update Encryption Key File "5060", Audio Port: "65002", Video Port: "65202", and Web Port: "443".
IP Video Intercom Adaptor Settings Adaptor Language Settings Saving the settings You can select the language used for the IP Video Intercom Adaptor Email transmissions, etc. from "English", "French", "Spanish", "German", "Dutch", "Italian", and "Japanese". The default setting is "English". Save the changed settings. 1. Click [SAVE]. ・"[Network] Setting has been saved." is displayed, and the Reboot Confirmation dialog is displayed. 1.
IP Video Intercom Adaptor Settings 3. Click [Save]. 3-3-6 Log Downloading / Firmware Update ・The Save As dialog is displayed and you can give the file a Log Downloading (for Inspections and Maintenance) name. For maintenance and inspection, you can acquire the operations log from the IP Video Intercom Adaptor. MEMO • If you are logged in as a User, you cannot perform a Log Downloading/Firmware Update. • The IP Video Intercom Adaptor records the most recent 10 days worth of operations logs.
IP Video Intercom Adaptor Settings 2. Enter a version for Update Firmware and FTP Server Firmware Update Address, and then click [Update]. To update the IP Video Intercom Adaptor firmware, you need to set the PC as a server beforehand and then save the firmware to be updated on the server. You may also need to turn off the Windows Firewall and security software functions. ・The Update Confirmation dialog is displayed.
IP Video Intercom Adaptor Settings ・The downloaded update file is written to the circuit board. Writing takes about 2 minutes. ・"Firmware update was completed successfully." is displayed, and the update process is complete. MEMO • Do not turn off the power while the firmware is being written. If the power is turned off while it is writing, the product will malfunction. 4. Click [Reboot]. ・[System is initializing. Please wait. Elapsed Time XX seconds.
IP Video Intercom Adaptor Settings 3-4 User Settings Registration : Administrator/User 3. Click [Save]. User Settings for the PC Application can be made from the User Settings window while logged in as the Administrator or a User. ・The Save As dialog screen is displayed and you can give the file a name.
IP Video Intercom Adaptor Settings 6. Select the Encryption Key File corresponding to the 3-4-2 Email Setting selected "Adaptor". Various User Settings for the PC Application can be made from the User Settings window while logged in as the Administrator or a User. MEMO • You cannot change settings for multiple IP Video Intercom Adaptors at the same time. Make various settings for each IP Video Intercom Adaptor. 7. Click [SAVE]. Use the following method to display the User Settings window.
IP Video Intercom Adaptor Settings 3. Click [SAVE]. Setting the Target Email Address and the Email Timing ・"[Email Setting] Setting has been saved." is displayed, the Register the Email Address of the receiver to which a notification is to be sent when a Door Call, Sensor Detection, or System Start is detected. entered Email Address is set, and you are returned to the User Settings window.
PC Application Settings 4 PC Application Settings 4-1 Setting the PC Application Registration : Administrator/User Various settings for the PC Application can be made from the PC Application Settings window. Use the following method to display the PC Application Settings window. 4-1-1 Volume Settings To adjust the volume, click the "Volume" tab from the PC Application Settings window to display the settings screen. The following 3 settings come under Volume Settings. 1.
PC Application Settings 2. Click [SAVE]. 4-1-2 Preferences Settings ・The Volumes are set and the PC Application Settings To adjust the Preferences Settings, click the "Preferences" tab from the PC Applications Settings window to display the settings screen. The following 6 settings come under Preferences settings. • Language Selection Settings • Max.
PC Application Settings Event Notification Operation List Setting Description Max. Recording Space Settings You can set the Max. Recording Space for images to between "00.01" and "10.00" GB. The default setting is "01.00". Reference Maximize Application When there is a call from (one of) the door station(s), or when Sensor Detection occurs (even when minimized), the PC Application is automatically maximized.
PC Application Settings Audio Recording Settings You can select whether or not to make an audio recording during manual video recording. The default setting is "OFF" (No audio recording performed). 1. Click [ON] or [OFF] in Audio Recording. ・When performing Audio Recording, be sure to set Picture Recording Mode to [Video]. You can not make audio recordings when [Snapshot] is set.
PC Application Basic Operations 5 PC Application Basic Operations 5-1 Video Intercom Functions By using the PC Application, you can operate the following video intercom functions for the video intercom system and synchronized devices (electronic door lock and other connected devices, etc.) connected to the IP Video Intercom Adaptor.
PC Application Basic Operations 2. Click [TALK] (j), for a call from the door station. 5-1-2 Door release ・You can click [TALK] (j) to communicate, even if the screen for image acquisition is displayed. While being called from the door station, talking or mon itor i ng, you ca n u n lock t he door f rom t he PC Application by clicking [ (Door release)] on the PC Application. 1. Click [ (Door release)]. ・The door is unlocked while the button is clicked and held. (Door release)] turns red.
PC Application Basic Operations Pan & Tilt operation 5-1-3 Zoom/Wide, Pan & Tilt By using the following steps, the monitor screen of the PC Application can be switched between a wide picture and a zoom picture. 1. Click the [ (Pan & tilt)] (k) pqtu buttons while a zoom picture is displayed. • Calling from the door station • Entrance monitoring • Communicating with the door station By using Pan & Tilt when a zoom picture is displayed, a wide picture can be split into 9 images and displayed as 1 picture.
PC Application Basic Operations 5-1-4 Adjust image 5-1-5 Room-to-room communication (Communication with a master monitor station) If the image displayed on the PC Application screen is difficult to see, you can adjust the image using [ADJUST] (j). You can adjust the backlight during the day when a bright background makes it difficult to see. You can make it brighter at night when it is darker. Mutual calls and communication are possible between the PC Application and the master monitor station.
PC Application Basic Operations 3. You can communicate when a master monitor station Calling / communicating with the master monitor station starts the communication. If you want to call a master monitor station from the PC Application, you can choose to call all master monitor stations in the system, or call one specific master monitor station. ・When you are calling all the master monitor stations, communicate with the master monitor station which starts the communication first.
PC Application Basic Operations 5-1-6 Entrance monitoring MEMO • The entrance monitoring tur ns off automatically after approximately 1 minute. To monitor the entrance again, repeat from 1. You can monitor a door station from the PC Application. 1. From • During entrance monitoring, the entrance monitoring time the "Adaptor" display (j) in the Expanded Window, select one door station-connected IP Video Intercom Adaptor you want to monitor.
PC Application Basic Operations 5-1-7 Sensor Detection from Connected Equipment 5-1-8 Option Output from IP Video Intercom Adaptor You will be notified by the PC Application if sensors connected to the master monitor station and IP Video Intercom Adaptor are activated. You can operate equipment connected to the IP Video Intercom Adaptor from the PC Application. 1. If a sensor detects an abnormality, or the connected call MEMO • The [OPTION] button turns green while being operated. 1. Click [OPTION].
PC Application Basic Operations 5-2 Recording Function The PC Application can record images from the video intercom system connected to the IP Video Intercom Adaptor automatically or manually. Video recording when Auto Recording is set A video recording of the entrance is made when the following condition is met. • When the call button at the door station is pressed 5-2-1 Auto Recording See "Picture Recording Mode Settings" for more information on video recording settings. P.
PC Application Basic Operations 1. Click [(Rec)] (j), while communicating with the door 5-2-2 Manual recording station. You can make a snapshot recording or video recording of the entrance when the following conditions are met. • Calling from the door station • Entrance monitoring • Communicating with the door station Snapshot recording You can only record one snapshot image of the entrance manually when the following conditions are met.
PC Application Basic Operations 5-3 Playback Function 4. Select a playback operation. In the PC Application, you can play back, stop, pause, slow down the playback, and fast forward the recorded images. You can delete any unnecessary recorded files. ・The snapshot or video is displayed on the PC Application screen. If audio has been recorded for the video, the audio is also played back. 5-3-1 Play recorded image ・If you click another recorded file during playback, playback of the recorded file stops.
PC Application Basic Operations Button Name Description • • • (Next File) • • 5-4 Sending Email During normal playback The recorded file directly below the file currently being played is played back. During Stop The recorded file one line below the currently selected file is selected. During Pause The first frame in the recorded file directly below the file currently being paused is displayed.
6 Others Settings List Setting Contents Administrator Registration Administrator ID Administrator Password User ID User Registration User Password Adaptor Name Connection IP Address Subnet Mask Default Gateway Primary DNS Network Settings Secondary DNS (IP Video Intercom MAC Address Adaptor) Web Port Connection Port Connection Password Audio Port Video Port Update Encryption Key File Adaptor Email Address SMTP Server (Email) login ID Email Setting SMTP Password SMTP Server Port SSL Adaptor Language Setti
*1 Supported symbols ! # $ % & ’* + - / ? ^ _ ` { | } ~ ( ) < > [ ] ; @ . * 2 Supported symbols ! # $ % & ’* + - / = ? ^ _ ` { | } ~ ( ) < > [ ] : ; , @ . * 3 Supported symbols ! # $ % & ’* + - / = ? ^ _ ` { | } ~ . Operation Status Comment List "Status" list A list of comments displayed in the PC Application. A "Status" list displayed in the PC Application's Expanded Window.
Technical Precautions ・Cleaning: Clean the units with a soft cloth dampened with a neutral household cleanser. Do not use an abrasive cleanser or cloth. ・If you are experiencing difficulties with the device such as "Settings not working well", please check our homepage at http:// www.aiphone.net/.
Settings Information Memo Record your settings information. It will need when resetting or maintenance.
Example of Registration For LAN / WAN HUB / Router HUB / Router ② ① LAN / WAN ③ ④ ④ ③ + - HO P AI NE N LA ER W PO S ATU ST T AC -IP W JK S1 E S2 E S3 E S4 RY E RY B1 B2 R ON OFF POWE DC18V LAN GTH IP LEN STR m 11m 0.65∼ 1.
For Global Broadband router Broadband router ③ ⑦ ④ ② ⑤ ① ⑥ INTER-NET IP Video Intercom Adaptor ① Local IP Address and Subnet Mask of the IP Video Intercom Adaptor PC ③ Global IP Address of the broadband router on the IP Video Intercom Adaptor side ② Local IP Address of the broadband router ⑦ Enter if Email will be sent OFF except for the broadband router that is confirmed to support UPnP ③ Global IP Address of the broadband router on the IP Video Intercom Adaptor side Change if necessary.
Warranty Aiphone warrants thats its products have no material or workmanship defects under normal use conditions for two years after delivery to the end user. Aiphone will perform repair or replacement free of charge if the product is defective and the warranty applies to the defect. Aiphone reserves unto itself the sole right to make the final decision whether there is a defect in materials and/or workmanship and whether or not the product is under warranty.
