User's Manual Part 3

ManualsBrandsAiptek International ManualsComputers & AccessoriesBluetooth Tablet

Customizing Your Tablet

Step1

(For Wireless/Wired)

USB Tablet provides a testing function for you to find out the best

settings for your pen.

Wired USB Tablet

3 For wireless tablet - Make sure that you have completed

all the previous steps in Chapter 1 and Chapter 2.

For wired tablet - Make sure that you have connected your tablet

To PC via a USB cable and have installed the battery of the pen.

Wireless USB Tablet

USB Tablet icon

(Wireless)

USB Tablet icon

(Wired)

Note: If you cannot find

and , click Start menu and

then click Run and enter atwtusb.

Click OK and or will

show up.

If your tablet is enabled as a

Bluetooth Tablet, will appear

in Windows System tray. While

your tablet is enabled as a wired

tablet, will appear in

Windows System tray.

Left-click or icon and

the USB Tablet Window will

pop up.

3. Configuration

Configuration

Customizing Your Tablet

(For Wireless/Wired)

Step1

Adjusting Your Wireless

Pen Sensitivity

(For Wireless/Wired)

Step2

Summary of content (8 pages)

PAGE 1
Step1 Customizing Your Tablet (For Wireless/Wired) 3 For wireless tablet - Make sure that you have completed all the previous steps in Chapter 1 and Chapter 2. For wired tablet - Make sure that you have connected your tablet To PC via a USB cable and have installed the battery of the pen. 1 If your tablet is enabled as a Bluetooth Tablet, will appear in Windows System tray. While your tablet is enabled as a wired tablet, will appear in Windows System tray.
PAGE 2
1 Click category tabs About USB Tablet Window 3. Configuration Change the length unit of tablet size in inch/cm. 21 Tracking Mode Click OK to save changes. Pen [Absolute mode] - the area of the tablet corresponds to the whole area of the screen. For example, if place your wireless pen in the top right hand corner, the mouse pointer will always be at the top right of the screen. Mouse [Relative mode] - acts like a mouse, moves in relation to where the mouse pointer currently is.
PAGE 3
2 Buttons Customizing Your Tablet There are two buttons on the wireless pen. Both of them can correspond to mouse click. Pull-down menu of Side Buttons of your wireless pen Click the Side Buttons menu and choose one function for each Side Button.
PAGE 4
3 Control The control tab allows configuration of the active working area of the tablet to a smaller area. 1 2 1. The Full Area button allows the entire area of the tablet to be used. (Default setting) 3. Configuration 3 23 2. To select a smaller active area, use the wireless pen and on the tablet click on the upper left corner of the area you wish to select, then move your wireless pen to the lower right of the area you wish to select and click. 3.
PAGE 5
4 Function Key Customizing Your Tablet The function key tab allows you to view or change existing shortcuts. To change a shortcut click on .. And search for the file you wish to link the function key to. You may also type the location. Once a function key is linked, the next time you want to access that file or location, just click on the respective function key. There are F1 - F12 to view or change F9 onwards, click Page Down.
PAGE 6
Step2 Adjusting Your Wireless Pen Sensitivity (For Wireless/Wired) 3. Configuration 1 25 Click Test to pop up the Click Pressure Test Window. The Click Pressure slider allows you to adjust the sensitivity of your pen as a percentage of the entire sensitivity. The figure in the box ranges from 0-30, with 0 as the most sensitive and 30 as the least possible setting. In practice, when you push your wireless pen gently on the tablet, the tablet detects a pressure starting from 0 (if you set 0).
PAGE 7
Write or draw anything on your tablet. The Window will display your writing or drawing. Feel the sensitivity of your pen and adjust Click Pressure Slider for your preference. ! Note: Your writing and drawing on Click Pressure Test Window cannot be saved.
PAGE 8
4 4.