Installation Guide

INSTALLATION
1. Locate a stud behind wall. If stud cannot be found, special types
of mounting anchors are available at your hardware store.
2. Secure Mounting Plate to wall with Screws supplied (#8 X 1 1/4"
Wood Screws). Make sure flange is pointing up as shown in
exploded view above.
3. Fan is now ready to hang on Mounting Plate.
MODEL 4CH64F/9018F
Rev. M 10/09
2
2084046
Rev. M 10/09
7
2084046
ASSEMBLY (Figure 1)
1. Put Rear Grill on Motor by aligning the tab on the Rear Grill
with the groove on the Motor. (Detail 1)
2. Fully seat Rear Grill on Motor and secure with Plastic Nut
turning Clockwise.
3. Slide Blade onto Motor Shaft. (Align groove on blade hub with
pin on motor shaft.) (Detail 2)
4. To secure Blade, screw Spinner onto Shaft
Counter Clockwise until tight on Blade hub.
5. Snap Front Grill into place.
Motor
Detail 1
Rear
Grill
Plastic
Nut
Blade
Spinner
Front
Grill
Ornament
OPERATION
VARIABLE OSCILLATION: Pull oscillation knob on the rear of the
motor up. Turn fan head to left, right, or straight ahead. Push
oscillation knob down and fan will oscillate about the set angle.
MAINTENANCE
WARNING: ALWAYS UNPLUG THE CORD FROM OUTLET
BEFORE MOVING OR SERVICING THIS FAN.
WARNING: DO NOT IMMERSE FAN IN WATER!
CLEANING: Use a soft cloth moistened with a mild soap solu-
tion, such as liquid dish washing detergent. Dry ALL PARTS COM-
PLETELY before reassembling. After any maintenance or servicing,
completely reassemble unit as described in this instruction manual
before reconnecting to the power supply.
CAUTION: Do not use gasoline, benzine, thinner, harsh
cleaners, etc. as they will damage the Fan. NEVER USE
ALCOHOL OR SOLVENTS.
LUBRICATION: Precision bearings are sealed at the factory for
life and will not require any further lubrication.
STORAGE: Store the Fan, with these instructions, in a cool, dry
place.
VERTICAL ANGLE: To adjust vertical angle, tilt fan head up or
down, as desired.
SPEED: Speed is controlled by a pull-cord switch. The speed setting
is shown by switch knob on front cover. (Off-High-Med-Low-Off)
POWER SUPPLY CORD: Plug power supply cord into a wall outlet
(AC 120Volts, 60 Hz).
KEY PARTE NO. DESCRIPCIÓN CANT.
1
2
3
3
4
5
6
9
7
8
11
12
20
19
16
18
17
18
15
13
14
21
22
23
24
25
26
10
Detail 2
Groove
Pin
MODELO 4CH64F/9018F
1 2060316B Placa de Montaje 1
2 2090003 Tornillo para Madera #8 X 11/4" 2
3 02090045A Tornillo #8 X 3/4" PPH Tipo 25 6
4 02090272 Pie de Hule 2
5 2060202 Placa Posterior para Colgar 1
6 2010554 Cubierta del Cable del Interruptor 1
7 2090008 Tornilla #8 X 1/2" 2
8 02055047 Interruptor con Cadenilla de Tiro 1
9 7091854 Plastico Protector 2
10 2010512P Cuerpo 1
11 2090539 Buje de la Cadenilla de Tiro 1
12 02090744 Pendiente 1
13 02035054 Conjunto del Motor 1
14 02010162B Placa de Trinquete 1
15 02090518 Resorte de Elevación 1
16 02090521A Eje de Elevación 1
17 02090033 Tuerca Hexagonal 1
18 02010548A Botones H.C. 2
19 2010131 Perilla del Interruptor 1
20 02050009FPB Conjunto del Cable 1
21 2096112 Parrilla Posterior 1
22 2010359 Tuerca de Protección 1
23 2010033 Aspa 1
24 2010093 Rotador 1
25 02096103 Parrilla Anterior 1
26 02010381A Ornamento 1