Technical Specifications

WARNING: THIS PLUG IS A SAFETY FEATURE. TO
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND
PERSONAL INJURY, DO NOT REMOVE, REPLACE,
REPAIR OR TAMPER WITH THE ORIGINALLY SUPPLIED
PLUG. IF THE FAN DOES NOT FUNCTION PROPERLY, IT
MAY BE DUE TO THE SAFETY DEVICE INCORPORATED
IN THIS PLUG. RETURN TO AN AUTHORIZED SERVICE
CENTER OR CALL 800-233-0268, MONDAY - FRIDAY,
BETWEEN 8:00 AM AND 5:00 PM EST. IF THE PLUG
WARNING LABEL IS MISSING OR DAMAGED, CALL THE
TOLL FREE NUMBER FOR A REPLACEMENT LABEL.
8. Where possible, avoid the use of extension cords. If they must
be used, minimize the risk of overheating by ensuring that they
are UL listed. Never use a single extension cord to operate more
than one Fan.
9. Do not operate any Fan with a damaged cord or plug or after the
Fan malfunctions, has been dropped or damaged in any manner.
Return Fan to authorized service facility for examination, electrical
or mechanical adjustment or repair.
10.Do not insert or allow ngers or foreign objects to enter any
ventilation or exhaust opening as it may cause an electric shock
or re, or damage the Fan. Do not block or tamper with the Fan
in any manner while it is in operation.
11.Always place the Fan on a stable, at, level surface when operating,
to avoid the chance of the Fan overturning. Locate the Power
Cord so the Fan or other objects are not resting on it. Do not run
Power Cord under carpeting. Do not cover Power Cord with throw
rugs, runners, or the like. Arrange Power Cord away from room
trafc and where it will not be tripped over.
12.This Fan is not intended for use in wet or damp locations. Never
locate a Fan where it may fall into a bathtub or other water container.
13. Do not use Fan outdoors.
14.This Fan is not suitable for use in hazardous locations. Please
refer to National Electric Code (NEC) Article 500 or applicable
state or local codes or standards relating to electrical requirements
for Hazardous locations. THIS FAN DOES NOT MEET THE
REQUIRMENTS OF NEC ARTICLE 500 (2002).
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK DO NOT USE THIS FAN WITH ANY SOLID STATE
SPEED CONTROL DEVICES.
FLOOR/TABLE FAN
18" (45.7 cm) MODEL 9218
Rev. Q 9/07 1 5084006
Motor ...................................... 120V, 60 Hz
Blade diameter ........................ 18" (45.7 cm)
Speeds .................................... 3
Control..................................... Rotary Switch
Air ow distribution .................. 90°
Approvals................................. UL Listed. Close mesh fan guard
meets OSHA requirements.
SPECIFICATIONS
DESCRIPTION
The Air King
®
18" (45.7 cm) oor/table fan features whisper-quiet performance
with a 3-paddle fan blade. The fan has a sealed permanently lubricated ball
bearing motor with a 9 ft (2.7 m) 18/3 cord set, and is constructed of sturdy,
powder coated steel.
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DE-
SCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY
WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
OPERATING INSTRUCTIONS & PARTS MANUAL
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precau-
tions should always be followed to reduce the
risk of re, electric shock and injury to person,
including the following:
1. Read all instructions before using Fan.
2. Make certain that the power source conforms to the electrical
requirements of the Fan.
3. Use this Fan only as described in this manual. Any other use
not recommended by the manufacturer may cause re, electrical
shock, or injury to persons.
4. Unplug power cord before installing, servicing, or moving the Fan.
WARNING: DO NOT DEPEND UPON THE ON-OFF SWITCH
AS THE SOLE MEANS OF DISCONNECTING POWER WHEN
INSTALLING OR SERVICING THE FAN. ALWAYS UNPLUG
THE POWER CORD.
5. This Fan must NOT be used in potentially dangerous lo-
cations such as ammable, explosive, chemical-laden or
wet atmospheres.
6. DO NOT use Fan in or near a window. Rain may create an
electrical hazard.
7. The power cord is equipped with a three-prong grounded plug
that must be inserted into a matching receptacle. Under no
circumstances should the grounding prong be cut off the plug.
Where a two-prong wall receptacle is encountered, it must be
replaced with a properly grounded three-prong receptacle installed
in accordance with the National Electrical Code (NEC) and all
applicable local codes and ordinances. This work must be done
only by a qualied electrician, using copper wire only.
WARNING: USE OF A THREE-PRONG TO TWO-PRONG
ADAPTER IS NOT RECOMMENDED. IMPROPER CONNEC-
TION MAY CREATE THE RISK OF ELECTROCUTION. USE
OF SUCH ADAPTERS IS NOT PERMITTED IN CANADA.
SAVE THESE
INSTRUCTIONS

Summary of content (4 pages)