Installation Guide

SECTION 7
Ducting
CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL
BUILDING CODES.
WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
1. Connect the ducting to the hood’s duct collar and damper. Secure in place using
tape to seal all joints (Figure 10).
CAUTION: ALWAYS DUCT THE FAN TO THE OUTSIDE THROUGH A WALL
OR ROOF CAP.
SECTION 8
Finishing the Installation
1. Reinstall the bottom cover removed in Section 1 using the 4 screws to secure it in place.
2. Reinstall the filters by fitting them into the channel on either side of the hood and
pushing upwards on them until they are secured in place (Figure 11).
www.airkinglimited.com
0000000 New 6-11 4 of 12
3. Install the included 26 watt fluorescent lamp into the lamp holder by lining up
the pins on the lamp base to the socket of the lamp holder and gently turning
clockwise until the lamp snaps into place and is firmly seated in the lamp holder.
Install a 4 watt maximum type C7 (candelabra base) night light (not included) into
the side lamp holder and reinstall the lamp cover by squeezing the cover’s sides
and fitting them into the slots on the hood.
4. Set both rocker switches to "OFF" position & restore power. Test that the light and
the fan are operating properly.
5. If there is any vibration noise, check for the source and try to tighten fasteners or
adjust the tape to make a tighter connection or seal.
SECTION 9
Controls
Your Range Hood is controlled by two remote rocker switches with one controlling the lighting
and the other controlling the exhaust fan. Each rocker switch has three positions, left, center,
and right. For the fan switch, the left position (I) is low speed, while the right position (II) is high
speed. The left position of the light switch (
°
) illuminates the Night Light only, while the right
position (
•
) illuminates the Main Light only. The center of both switches is the "OFF" position."
SECTION 10
Maintenance
CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL
BEFORE SERVICING THE UNIT.
Filters
1. Grease Filter - Included with your range hood are aluminum grease filters that
should be washed at least once a month. The filters are dishwasher safe and
should be washed in a mild soap or detergent. Reverse the instructions in the
“Finishing the Installation” section of the instructions to remove filters. If the grease
filters become damaged, replace with Air King Model GF-01 Grease Filters.
2. Charcoal Odor Filter - If you have installed the optional charcoal odor filters, they
cannot be washed and must be discarded and replaced when they become notice-
ably dirty, have stopped filtering the odors, or at least once per year. Replace with
Air King Model CF-01 Odor Filters.
Changing the Lamp
1. Remove the lamp cover by squeezing in the sides. The cover is held in place by
tension against the tabs on the hood.
Fluorescent Lamp: Remove lamp by gently twisting counterclockwise to release
the lamp from the base. Installation is the reverse of removal. Replace with Air King
model 26SBL or a compatible 26W GU24 lamp.
Night Light: Unscrew night light bulb from socket and replace with a 4 watt maximum
type C7 (candelabra base) night light bulb.
Fuse
1. To replace the fuse, turn the fuse cap located next to the wire connector counter
clockwise and pull out. Replace with only a 125-Volt fuse, 1-1/2 Amp Max. Reinstall
the fuse back into the hood (Figure 7).
Cleaning
CAUTION: DO NOT USE GASOLINE, BENZINE, THINNER, HARSH CLEANSERS,
ETC., AS THEY MAY DAMAGE THE RANGE HOOD.
1. Clean your range hood with a mild detergent, such as dishwashing liquid, and dry with
a soft cloth. NEVER USE ANY ABRASIVE PADS OR SCOURING POWDERS. Completely
dry before restoring power. NEVER IMMERSE ELECTRICAL PARTS IN WATER.
2. The fan assembly can be vacuumed when build up (dirt, lint, etc.) accumulates
over time. The fan is permanently lubricated and does not require oiling.
Channel
Figure 11
Figure 10
Figure 9
Green or Bare
120V Supply
at Range Hood
Fan
Switch
Light
Switch
Red
Black
White
Red
Black
White
Red
White
Black
Green or Bare
White
Black
Green or Bare
White
Blue
Red
Night
Light
Lamp
White
White
Black
Black w/Red band
3 mf
250 Volt
Fuse
1.5 AMP
Green pigtail (w/eyelet)
screwed to metal body
Cable A
Cable B