Installation Guide

CAUTION: ALWAYS DUCT THE FAN TO THE OUTSIDE THROUGH A
WALL OR ROOF CAP.
SECTION 8
Finishing the Installation
1. Reinstall the bottom cover removed in Section 1 using the 4 screws to secure it in place.
2. Reinstall the filters by fitting them into the channel on either side of the hood and
pushing upwards on them until they are secured in place (Figure 11).
3. Install the included 8 watt LED lamp into the lamp holder by lining up the pins on the
lamp base to the socket of the lamp holder and turning the lamp body clockwise until the
lamp snaps into place and is firmly seated in the lamp holder. Install a 4 watt maximum
type C7 (candelabra base) night light (not included) into the side lamp holder and reinstall
the lamp cover by squeezing the cover’s sides and fitting them into the slots on the hood.
4. Turn switches to the “OFF” position and restore power. Test that the light and the fan are
operating properly.
5. If there is any vibration noise, check for the source and try to tighten fasteners or adjust
the tape to make a tighter connection or seal.
SECTION 9
Controls
Your Range Hood is equipped with two rotary switches with one controlling the lighting and
the other controlling the exhaust fan. The light switch has three positions, Main Light ( ),
Night Light ( ), and OFF ( ). The fan switch has four positions, High, Medium, Low, and OFF.
SECTION 10
www.airkinglimited.com
5084457 Rev. Q 11-16 4 of 12
Maintenance
CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE
SERVICING THE UNIT.
Filters
1. Grease Filter - Included with your range hood are aluminum grease
filters that should be washed at least once a month. The filters are dishwasher safe and
should be washed in a mild soap or detergent. Reverse the instructions in the “Finishing
the Installation” section of the instructions to remove filters. If the grease filters become
damaged, replace with Air King Model GF-01 Grease Filters.
2. Charcoal Odor Filter - If you have installed the optional charcoal odor filters, they cannot
be washed and must be discarded and replaced when they become noticeably dirty, have
stopped filtering the odors, or at least once per year. Replace with Air King Model CF-01
Odor Filters.
Changing the Lamp
1. Remove the lamp cover by squeezing in the sides. The cover is held in place by tension
against the tabs on the hood.
LED Lamp: Remove lamp by gently twisting counterclockwise to release the lamp from
the base. Installation is the reverse of removal. Replace with Air King model AK8LED40 or
a compatible GU24 8 watt LED lamp
Night Light: Unscrew night light bulb from socket and replace with a 4 watt maximum
type C7 (candelabra base) night light bulb.
Fuse
1. To replace the fuse, turn the fuse cap located next to the wire connector counter
clockwise and pull out. Replace with only a 125-Volt fuse, 1-1/2 Amp Max. Reinstall the
fuse back into the hood (Figure 7).
Cleaning
CAUTION: DO NOT USE GASOLINE, BENZINE, THINNER, HARSH CLEANSERS,
ETC., AS THEY MAY DAMAGE THE RANGE HOOD.
1. Clean your range hood with a mild detergent, such as dishwashing
liquid, and dry with a soft cloth. NEVER USE ANY ABRASIVE PADS OR SCOURING
POWDERS. Completely dry before restoring power. NEVER IMMERSE ELECTRICAL
PARTS IN WATER.
2. The fan assembly can be vacuumed when build up (dirt, lint, etc.) accumulates over time.
The fan is permanently lubricated and does not require oiling.
CALIFORNIA RESIDENTS ONLY:
WARNING: THIS PRODUCT CAN EXPOSE YOU TO A CHEMICAL [OR
CHEMICALS] KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER.
WARNING: THIS PRODUCT CAN EXPOSE YOU TO A CHEMICAL [OR
CHEMICALS] KNOWN TO THE STATE OF CALIFORNIA TO CAUSE REPRODUCTIVE
TOXICITY.
Channel
Figure 11
Figure 10