User's Manual
Table Of Contents
- Product Manual
- And Installation Guide
- Introduction
- Hardware Description
- Backhaul / Point-to-point Architecture
- Multipoint Architecture
- Repeater Architecture
- Mesh Architecture
- System Requirements
- Hardware Installation
- Installing and Visually Aligning Outdoor Units
- Software Configuration
- Getting Started
- Logging into the WirelessGRID NMS
- Current Settings
- Wired Network Settings
- Radio Network Settings
- WirelessGRID Bridge List
- WirelessGRID System Setup Tab
- Network Settings Tab
- Radio Settings Tab
- Admin Setup Tab
- Security Tab – Data Encryption
- WirelessGRID Authentication
- Data Encryption
- Encryption Key Manager
- Security Server (RADIUS) Settings
- Active Bridge Status Tab
- Remote Bridge (SU Station) Statistics Tab
- Firmware Update Tab
- Help Tab
- Antenna alignment and link monitoring tool
- Using the real-time signal strength monitor for antenna alignment
- Antenna Adjustment Using the real-time Signal Strength Monitor
- Specifications
- _
- _
- 4.940-4.990 GHz Public Safety Band (FCC Part 70, licensed Intl.)Non-overlapping Channels: 8 x 5 MHz, 4 x 10 MHz, 2 x 20 MHz, 1 x 40 MHz
- 5.25-5.35 GHz license-exempt (FCC, Industry Canada, Mexico)Non-overlapping Channels: 19 x 5 MHz, 9 x 10 MHz, 4 x 20 MHz, 2 x 40 MHz
- 5.47-5.72 GHz license-exempt (ETSI, FCC, ITU) with TPC and DFSNon-overlapping Channels: 44 x 5 MHz, 22 x 10 MHz, 11 x 20 MHz, 5 x 40 MHz
- 5.725-5.850 GHz licence exempt UNII & ISM Bands (ETSI, FCC, MII) Non-overlapping Channels: ISM, UNII: 25 x 5 MHz, 12 x 10 MHz, 5 x 20 MHz, 2 x 40 MHz
- Orthogonal Frequency Division Multiplexing (OFDM)
- 802.3, 802.11i draft, 802.11a hardware with proprietary bridging extensions
- Radio output power: Max: 21dBm (Set to local regulatory requirements to comply with transmit, conducted and EIRP power limits)
- Data Rate: 1 to 108 Mbps
- Sensitivity: -73 to –91dBm
- Modulation: 64QAM, 16QAM, QPSK, BPSK
- Point to Multipoint, Point to Point, Repeater (See Ordering Guide)
- AI108-4958-BSU, AI108-4958-ON2 - Order a Sector, Omni, GRID, or Panel AI108-4958-SU and -1: Flat Panel Directional Antenna AI108-4958-0-xxx: 23 dBi integrated or 28 dBi external directional antenna. External antennas may be used with local regulatory ap
- MAXIMUM RADIO OUTPUT POWER FOR US
- Frequency(GHz) 5.25-5.35 5.725-5.85 5.725-5.85
- 23dB Patch 7 13 MAX
- 28dB Grid 2 8 MAX
- 9dB Omni N/A 27 MAX
- 17dB Sector N/A 19 MAX
- Up to 7.5 miles (12 km) with built-in 23 dBi panel antennasUp to 30 miles (48.27 km) with max radio output power and optional external 34.5 dBi antennas
- Up to 30 miles (48.27 km) - N-type version (AI108-4958-ON-xxx) with max radio output power and optional external 34.5 dBi antennas
- _
- _
- Ordering Information
- WirelessGRID Worldwide Frequency Channel Plan
- Appendix A – Bench Test Procedure
- _
- Step 1. Setup a wired Ethernet network between test stations
- Step 2. Setup wired Ethernet network connections to bridges
- Step 3. Setup bridge software configuration for bridge
- Step 4. Test network connectivity across a WirelessGRID link
- Step 4a. Check throughput of WirelessGRID link (optional)
- Step 5. Running the real-time Signal Strength Monitor
- Step 6. Field deployment of WirelessGRID bridges
- Appendix B. Multi-point Bridge Configuration Log
- Appendix C: Weatherproofing RF Cable Connections
- How to Get Help
Airaya – Fast and affordable outdoor wireless bridges
Network Settings Tab
The Network Settings screen is used to modify your network IP Address,
Subnet Mask, and Default Gateway Address.
The screen includes the following entries:
IP Address – The IP address of the bridge you are working with. The IP
address for each bridge must be unique; check with your network
administrator for the correct IP address assigned to this device. Default IP
address: 192.168.1.70.
Subnet Mask – The subnet mask allows networking software to
determine which parts of the IP address specify the network address and
which parts specify the host address. Default Subnet Mask:
255.255.255.0.
Default Gateway Address – IP packets destined for other subnets are
automatically sent to the default gateway, which routes the traffic to the
correct network. The gateway address must be specified following the
same convention as the IP address. Default Gateway Address:
192.168.1.1.
- 23 -