User's Manual
Table Of Contents
- Product Manual
- And Installation Guide
- Introduction
- Hardware Description
- Backhaul / Point-to-point Architecture
- Multipoint Architecture
- Repeater Architecture
- Mesh Architecture
- System Requirements
- Hardware Installation
- Installing and Visually Aligning Outdoor Units
- Software Configuration
- Getting Started
- Logging into the WirelessGRID NMS
- Current Settings
- Wired Network Settings
- Radio Network Settings
- WirelessGRID Bridge List
- WirelessGRID System Setup Tab
- Network Settings Tab
- Radio Settings Tab
- Admin Setup Tab
- Security Tab – Data Encryption
- WirelessGRID Authentication
- Data Encryption
- Encryption Key Manager
- Security Server (RADIUS) Settings
- Active Bridge Status Tab
- Remote Bridge (SU Station) Statistics Tab
- Firmware Update Tab
- Help Tab
- Antenna alignment and link monitoring tool
- Using the real-time signal strength monitor for antenna alignment
- Antenna Adjustment Using the real-time Signal Strength Monitor
- Specifications
- _
- _
- 4.940-4.990 GHz Public Safety Band (FCC Part 70, licensed Intl.)Non-overlapping Channels: 8 x 5 MHz, 4 x 10 MHz, 2 x 20 MHz, 1 x 40 MHz
- 5.25-5.35 GHz license-exempt (FCC, Industry Canada, Mexico)Non-overlapping Channels: 19 x 5 MHz, 9 x 10 MHz, 4 x 20 MHz, 2 x 40 MHz
- 5.47-5.72 GHz license-exempt (ETSI, FCC, ITU) with TPC and DFSNon-overlapping Channels: 44 x 5 MHz, 22 x 10 MHz, 11 x 20 MHz, 5 x 40 MHz
- 5.725-5.850 GHz licence exempt UNII & ISM Bands (ETSI, FCC, MII) Non-overlapping Channels: ISM, UNII: 25 x 5 MHz, 12 x 10 MHz, 5 x 20 MHz, 2 x 40 MHz
- Orthogonal Frequency Division Multiplexing (OFDM)
- 802.3, 802.11i draft, 802.11a hardware with proprietary bridging extensions
- Radio output power: Max: 21dBm (Set to local regulatory requirements to comply with transmit, conducted and EIRP power limits)
- Data Rate: 1 to 108 Mbps
- Sensitivity: -73 to –91dBm
- Modulation: 64QAM, 16QAM, QPSK, BPSK
- Point to Multipoint, Point to Point, Repeater (See Ordering Guide)
- AI108-4958-BSU, AI108-4958-ON2 - Order a Sector, Omni, GRID, or Panel AI108-4958-SU and -1: Flat Panel Directional AntennaAI108-4958-0-xxx: 23 dBi integrated or 28 dBi external directional antenna. External antennas may be used with local regulatory app
- Up to 7.5 miles (12 km) with built-in 23 dBi panel antennasUp to 30 miles (48.27 km) with max radio output power and optional external 34.5 dBi antennas
- Up to 30 miles (48.27 km) - N-type version (AI108-4958-ON-xxx) with max radio output power and optional external 34.5 dBi antennas
- _
- _
- Ordering Information
- WirelessGRID Worldwide Frequency Channel Plan
- Appendix A – Bench Test Procedure
- _
- Step 1. Setup a wired Ethernet network between test stations
- Step 2. Setup wired Ethernet network connections to bridges
- Step 3. Setup bridge software configuration for bridge
- Step 4. Test network connectivity across a WirelessGRID link
- Step 4a. Check throughput of WirelessGRID link (optional)
- Step 5. Running the real-time Signal Strength Monitor
- Step 6. Field deployment of WirelessGRID bridges
- Appendix B. Multi-point Bridge Configuration Log
- Appendix C: Weatherproofing RF Cable Connections
- How to Get Help
Airaya – Fast and affordable outdoor wireless bridges
Country Code – Select the Country Code for the location in which the
WirelessGRID will be operating. If you are not sure select N/A; all channel
options available in the WirelessGRID network will be provided. Changing
the Country Code will change available Wireless Mode, Radio Frequency
(center channels), and Data Rate options for your WirelessGRID.
NOTE
When you have finished updating the Country Code, make sure
to press Update to view revised Wireless Mode, Radio
Frequency, and Data Rate settings.
Wireless Mode – Select the desired channel size for your AIRAYA
WirelessGRID bridge. The unit is capable of operating on 5, 10, 20 or 40
MHz wide channels.
NOTE
When you have finished updating the Wireless Mode, make sure
to press Update to view revised Radio Frequency, and Data Rate
settings.
Radio Frequency – Select the desired frequency of operation from the
drop-down menu. The radio frequencies that appear are dependent on the
Wireless Mode specified.
Data Rate – Select the desired data rate from the drop-down menu. The
data rates that appear are dependent on the Wireless Mode specified.
Transmit Power – Select the desired Transmit Power option from the
drop-down menu. The options are dependent on the Country Code
specified.
Follow these steps to update the radio network settings.
NOTE
You must press Update after each radio parameter change. Radio
parameters are interdependent, so each will change with every selection
you make.
1. Update the WirelessGRID ID.
2. Select Country Code (if drop down list is available)
3. Select Wireless Mode
4. Select Radio Frequency
5. Select Data Rate
6. Select Transmit Output Power
- 27 -