User's Manual
Table Of Contents
- Product Manual
- And Installation Guide
- Introduction
- Hardware Description
- Backhaul / Point-to-point Architecture
- Multipoint Architecture
- Repeater Architecture
- Mesh Architecture
- System Requirements
- Hardware Installation
- Installing and Visually Aligning Outdoor Units
- Software Configuration
- Getting Started
- Logging into the WirelessGRID NMS
- Current Settings
- Wired Network Settings
- Radio Network Settings
- WirelessGRID Bridge List
- WirelessGRID System Setup Tab
- Network Settings Tab
- Radio Settings Tab
- Admin Setup Tab
- Security Tab – Data Encryption
- WirelessGRID Authentication
- Data Encryption
- Encryption Key Manager
- Security Server (RADIUS) Settings
- Active Bridge Status Tab
- Remote Bridge (SU Station) Statistics Tab
- Firmware Update Tab
- Help Tab
- Antenna alignment and link monitoring tool
- Using the real-time signal strength monitor for antenna alignment
- Antenna Adjustment Using the real-time Signal Strength Monitor
- Specifications
- _
- _
- 4.940-4.990 GHz Public Safety Band (FCC Part 70, licensed Intl.)Non-overlapping Channels: 8 x 5 MHz, 4 x 10 MHz, 2 x 20 MHz, 1 x 40 MHz
- 5.25-5.35 GHz license-exempt (FCC, Industry Canada, Mexico)Non-overlapping Channels: 19 x 5 MHz, 9 x 10 MHz, 4 x 20 MHz, 2 x 40 MHz
- 5.47-5.72 GHz license-exempt (ETSI, FCC, ITU) with TPC and DFSNon-overlapping Channels: 44 x 5 MHz, 22 x 10 MHz, 11 x 20 MHz, 5 x 40 MHz
- 5.725-5.850 GHz licence exempt UNII & ISM Bands (ETSI, FCC, MII) Non-overlapping Channels: ISM, UNII: 25 x 5 MHz, 12 x 10 MHz, 5 x 20 MHz, 2 x 40 MHz
- Orthogonal Frequency Division Multiplexing (OFDM)
- 802.3, 802.11i draft, 802.11a hardware with proprietary bridging extensions
- Radio output power: Max: 21dBm (Set to local regulatory requirements to comply with transmit, conducted and EIRP power limits)
- Data Rate: 1 to 108 Mbps
- Sensitivity: -73 to –91dBm
- Modulation: 64QAM, 16QAM, QPSK, BPSK
- Point to Multipoint, Point to Point, Repeater (See Ordering Guide)
- AI108-4958-BSU, AI108-4958-ON2 - Order a Sector, Omni, GRID, or Panel AI108-4958-SU and -1: Flat Panel Directional AntennaAI108-4958-0-xxx: 23 dBi integrated or 28 dBi external directional antenna. External antennas may be used with local regulatory app
- Up to 7.5 miles (12 km) with built-in 23 dBi panel antennasUp to 30 miles (48.27 km) with max radio output power and optional external 34.5 dBi antennas
- Up to 30 miles (48.27 km) - N-type version (AI108-4958-ON-xxx) with max radio output power and optional external 34.5 dBi antennas
- _
- _
- Ordering Information
- WirelessGRID Worldwide Frequency Channel Plan
- Appendix A – Bench Test Procedure
- _
- Step 1. Setup a wired Ethernet network between test stations
- Step 2. Setup wired Ethernet network connections to bridges
- Step 3. Setup bridge software configuration for bridge
- Step 4. Test network connectivity across a WirelessGRID link
- Step 4a. Check throughput of WirelessGRID link (optional)
- Step 5. Running the real-time Signal Strength Monitor
- Step 6. Field deployment of WirelessGRID bridges
- Appendix B. Multi-point Bridge Configuration Log
- Appendix C: Weatherproofing RF Cable Connections
- How to Get Help
Airaya – Fast and affordable outdoor wireless bridges
Regulatory Information
FCC and Industry Canada Guidelines
The radiated output power of the AIRAYA WirelessGRID Wireless Bridge is far
below the FCC radio frequency exposure limits. Nevertheless, the device shall
be used in such a manner that the potential for human contact during normal
operation is minimized. It is the responsibility of the installer and users of the
WirelessGRID to guarantee that the antenna operates at least 20 centimeters
(8 inches) from any person. This is necessary to insure that the product
operates in accordance with the Federal Communications Commission’s RF
Guidelines for Human Exposure.
The WirelessGRID’s built-in antennas may NOT be replaced at any time. They
are designed to comply with the maximum EIRP limits specified by the FCC
and Industry Canada. Modifications to the WirelessGRID, unless expressly
approved by AIRAYA, could void the user's authority to operate the equipment.
The WirelessGRID wireless bridge operates in the 5.25 to 5.35 GHz frequency
range. High power radar systems in both Canada and the United States are
allocated as primary users of this spectrum. These radars can cause
interference and or damage to devices such as the WirelessGRID wireless
bridge when used outdoors.
The term “IC:” before the radio certification number only signifies that
Industry Canada technical specifications were met.
FCC ID: QDE-GRIDC3
IC: 4433A-GRIDC3
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION
IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE
MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
Class A Digital Compliance
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his or her own expense.
- 5 -