Full Product Manual

AD2000 AD2000
6 7
OPERATING THE AIRDOCTOR 2000 AIR PURIFIER OPERATING THE AIRDOCTOR 2000 AIR PURIFIER
Before rst use, remove lters and remove plastic bags from the Carbon Filter, then reinstall
lters and front cover.
Plug the unit into an electrical outlet, and it will be ready to run. Read the following instructions
to select desired settings.
AIR QUALITY MONITOR
The AirDoctor comes with an Air Quality Monitor that continuously monitors the quality of air in
a room. The LED indicator light, located on the top of the unit, will change colors based on the
air quality in the room. The Air Quality Monitor is able to show three air quality levels.
BLUE = Good air quality / ORANGE = Fair air quality / RED = Poor air quality
You can choose to set the AirDoctor to Auto. This will enable the AirDoctor to adjust the fan
speed according to the air quality. In Auto mode, the fan speed will be adjusted as follows:
Good Air Quality = Low fan speed
Fair Air Quality = Medium fan speed
Poor Air Quality = High and Boost fan speeds
CONTROL PANEL
1. Power Control
As soon as you press the power button
, the AirDoctor will start in the Auto mode.
Once the Auto mode has been activated, it will start up in the high-speed mode, and the
sensor will start to detect the amount of particulate matter in the air. As the particles are
detected, the AirDoctor will automatically adjust to the purication speed (fan speed) that
is appropriate to the particulate contamination in the room.
In most cases, we recommend that you leave the AirDoctor in the Auto mode.
For other purication modes, see the next page.
2. Fan Speed Control
The AirDoctor has four dierent fan speed settings: Low, Medium, High and Boost.
Each mode has its own indicator light that lights up when the setting is chosen. The
speed selected determines how rapidly you want to clean the air. The “Low” and
“Medium” settings are great for everyday use. The “High” setting is great for areas
with more airborne contaminants (such as excessive smoke, pet dander, etc.) or areas
used frequently by allergy suerers. The “BOOST” setting is best used for shorter
bursts of time when you want to rapidly purify the air.
3. Auto Mode
The AirDoctor is equipped with an air quality sensor to monitor the quality of your air.
Simply press the Auto button to activate the air-monitoring system. The monitor will test
the air quality and automatically adjust the fan speed to remove the air contaminants.
The LED ring is on the top of the unit to notify you of the air quality; RED color for poor,
ORANGE for fair and BLUE for good quality air.
4. Dim Mode
If the LED lights are too bright, activate the “Dim Mode” to turn them o.
5. Timer Control
The AirDoctor Professional Air Purier can be programmed to turn o after a preset
amount of time. Press the “TIMER” button to program the timer. Each press will add
1 hour up to a total of 24 hours. Keeping the button pressed will automatically increase
to 24 hours, 1 hour at a time. To turn o the timer, cycle through the numbers until you
reach the beginning, and no numbers show on the display.
6. Ionizer
The ionizer generates negative ions. This helps boost ltration performance by
causing contaminants to clump together and making them easier to capture, but also
creates a fresh air feeling. Press the Ion button to turn on the Ionizer. Press it again
to turn it o.
7. Replace Filter Indicator Light
The AirDoctor Replace Filter Indicator Light will turn on each time a lter needs to be
replaced. To reset the Replace Filter alert after you have changed out the appropriate lter,
press the Auto and Dim together for 3 seconds. The REPLACE FILTER light will ash
three times and then turn o completely, indicating the unit has been reset.
8. 24-Hour Timer Display
Air Quality Monitor
1
2 3 4 5 6 7 8
CONTROL LOCK FEATURE
The AirDoctor has a control lock feature to prevent a person (child) or a pet from
interrupting the running mode by accident. When the control lock feature has been
activated, none of the buttons on the control panel will work. The only way to change
any setting is to deactivate the control lock feature or to unplug the AirDoctor.
To activate control lock feature
• Press “Timer” and “Ion” at the same time for 3 seconds
• This may be done at any time while the AirDoctor
is running, including on Dim mode
To deactivate control lock feature
• Press “Timer” and “Ion” at the same time for 3 seconds