Full Product Manual

AD2000 AD2000
8 9
MAINTENANCE
MAINTENANCE
CLEANING THE AIR QUALITY SENSOR
The AirDoctor is designed with an air quality sensor to track the quality
of your air. Over time, the sensor can become dirty and may require
cleaning. The main symptom of a dirty air quality sensor is the LED air
quality monitor display that remains frozen on one light color. In order to
clean it, you must use a vacuum cleaner to clear the sensor chamber.
1. Power o and unplug unit.
2. Locate and open the air quality sensor cover located on
the side of the unit. (Fig. 1)
3. Use a vacuum cleaner hose to suction any dust or dirt that
may have accumulated inside the monitor chamber. (Fig. 2)
SENSOR CLEANING MAINTENANCE
The lens of the air quality particle sensor may also need to be cleaned.
1. Power o and unplug unit.
2. Locate and open the air quality sensor cover located on
the side of the unit. (Fig. 3)
3. Locate the lens of the air sensor located inside the air sensor. (Fig. 4)
4. Wet the one end of a cotton swab with water and wipe the lens to
remove any debris. Then, dry the lens with the other end of the swab
Caution: Do not scratch the lens with a hard object.
The AirDoctor professional air purier is almost
maintenance-free! The high-quality Carbon/Gas Trap/
VOC Filter lasts up to six months and our UltraHEPA Filter
lasts up to 12 months, depending on use and environment
conditions. Before replacing the UltraHEPA or Carbon/Gas
Trap/VOC Filter of your AirDoctor professional air purier,
turn o and unplug the unit from the electrical outlet and
read all safety instructions and important warnings in this
owner’s manual.
REPLACING THE ULTRAHEPA AND
CARBON/GAS TRAP/VOC FILTERS:
1. Make sure the unit is turned o and unplugged.
With the front of the unit facing forward, pull
the lid toward you at the upper end as shown
and remove the front cover.
2. Remove the UltraHEPA and Carbon/Gas Trap/VOC
Filters by lifting and pulling the tabs on both sides
of the lters.
3. Insert the new lter(s) that need replacing, then
insert the bottom of the inlet grill rst and then
snap the upper part of the front cover
back into position.
4. To close the front cover, rst make sure the bottom
hooks are properly in place before snapping it up
to its upright and locked position.
The importance of Genuine AirDoctor
Replacement Filters!
Genuine AirDoctor replacement lters are guaranteed by
AirDoctor and independently tested to remove dangerous
airborne contaminants. Generic (third-party) aftermarket
lters are of dubious quality, are not tested for eectiveness
and are not certied to work with AirDoctor to maintain
the Energy Star and CARB certication. AirDoctor has
tested several generic lters that do not even meet the
minimum HEPA standard. For air quality you can trust, and
to maintain the optimal performance you depend on from
AirDoctor, always use genuine AirDoctor replacement lters.
Warning: The use of generic, third-party replacement lters
can damage your AirDoctor purier and void your warranty.
CLEANING THE PRE-FILTER
1. Make sure the unit is turned o and unplugged.
With the unit facing forward, pull the cover towards
you at the upper end and remove the front cover.
2. Gently vacuum your Pre-Filter. You may do this
monthly or as needed if there is more build-up.
3. After you’ve vacuumed your Pre-Filter, simply place
the front cover back on your AirDoctor.
1
4
3
2
Figure 1
Figure 3
Figure 2
Figure 4
FAQ & TROUBLESHOOTING
Before contacting our customer service department, please try the following solutions:
QUESTION ANSWER
How often
should I change
the lters?
UltraHEPA - 12 months
Carbon/Gas Trap/VOC - 6 months
Can I wash
my lters?
It is important that you never wash your UltraHEPA or Carbon/VOC
Filters. Doing so will damage your lters, making them unusable.
Your Pre-Filter was designed to be reusable. Avoid washing your
Pre-Filter as you do not want to introduce any moisture onto the lters.
We recommend vacuuming your Pre-Filter monthly for best
maintenance and to extend the life of your lters until the
next lter change.
How long is the
power cord?
The power cord is 6 feet long.