Retro Valve Exploded View Click on any part for a larger view and description
Part #843 Regulator Valve Pin Assembly The Regulator Pin comes as an assembly. Just push it in place and it should be good to go. If you have problems with this part call the factory.
Part #844 Regulator Seat O-Ring The Regulator Seat O-ring is the business end of the regulator. Replace it if you are having problems with velocity. Two are included in the Parts Kit.
Part #841 Regulator Seat Holder The Regulator Seat Holder holds the O-ring that acts as the regulator seal.
Part #115 Regulator Body O-Ring The Reg. Body O-Ring seals the two halves of the Valve Body together. Included in the Parts Kit.
Part #779 Regulator Valve Pin O-Ring/ (On Off O-Ring) Four of these desogrin O-rings are used in the Retro Valve, two as part of the regulator valve pin assembly, one on the On/Off Pin and one in the face of the regulator body. Four included in the Parts Kit .
Part #796 Bumper – RT This clear urethane washer sits at the base of your power tube. When the bolt returns, it hits this to decelerate. This bumper is a little softer than the standard blue bumper for the higher firing rate of the Retro Valve. The bumper should be replaced about once a year. One Included in the Parts Kit.
Part #123 Power Tube O-Ring (On Off Bottom O-Ring) A common size O-ring in the marker. It's a good idea to have spares on hand. Included in the Parts Kit Used in the Power Tube and the On/Off assembly.
Part #736 Power Tube Spacer .220 The spacers are sold as a kit so you get several sizes. You need to swap them until you find the best size for your particular marker. Follow the link below to go to the spacer kits.
Part #781 Power Tube Tip O-Ring This O-ring keeps the Power Tube Tip from loosening up.
Part #826 Regulator Nut/RT The Regulator Nut screws into the back of the valve and adjusts the velocity. Keep the threads lubricated with a good grease.
Part #157 Regulator Nut O-Ring/Barrel O-Ring This is the same O-Ring used on most AGD barrels. Keeps the Regulator Nut in place.
Part #800 Regulator Spring /Outer The Retro Valve uses two coil springs behind the Regulator Piston. This is the larger of the two. Should never need replacing, just keep it greased.
Part #818 Power Tube Tip This item screws into the end of the Power Tube and is a precision part. It releases the air blast behind the ball in a controlled manner so the air hits the ball with low pressure to gently accelerate it out the barrel. Use a coin to tighten it up.
Part #799 Regulator Spring /Inner This is the smaller of the two springs that go behind the Regulator Piston. These springs assemble one inside the other.
Part #822 Regulator Piston Assembly The Regulator Piston comes as an assembly that has a built-in blow off valve. Do not disassemble! Replace this part when air is venting out the back of the marker and you are shooting less than 300 FPS.
Part #113 Regulator Piston O-Ring This O-ring goes around the Regulator Piston and is a wear item. Extras are found in the Parts Kit for a better value. Replace when the marker has erratic velocity problems and you have tried everything else.
Part #815 On Off Bottom On/Off Bottom is the lower half of the assembly. It screws into the On/Off Top.
Part #778 On Off Small O-Ring This urethane O-ring goes inside the On/Off Top. Included in the Parts Kit.
Part #814 On Off Top This is the top part in the On/Off Assembly. The On/Off small urethane O-ring sits inside.
Part #1083 On Off Pin .750 The Retro Valve On/Off Pin has a large head which makes it different from the Standard Valve. This feature contributes to the Reactive Trigger of the Retro Valve.
Part #802 Bolt-Foamieless Bolts from AGD are made from hardened stainless for extra long life. They come in three different types: 1. Hard Nose: all stainless construction including the tip that pushes on the paintball. Get this one if you don't want to fool around with replacing stuff. 2. Foamie: a small foam rubber cushion is glued to the front of the bolt to softly push your paintballs into the barrel. Good if you play a lot in cold weather.
Part #798 Bolt Spring The Bolt Spring fits all AGD markers regardless of age or type. They are made from very special square wire so they don't fold inside themselves when collapsed. Replace your old springs when they sag below the front of the bolt. Special honed bolt springs come with Superbolts to prevent premature wear. One spring also comes in the. Parts Kit. If you need any O-rings, the kit is a good value.
Part #1103 Retro Valve Package Because we laser engrave matching serial numbers on each half of the Valve Assembly, you can’t buy just one half of a Valve Assembly.
www.airgun.com www.automags.org Airgun-UK Email to: office@airgun.