Instruction manual
4
5
This sprayer operates at 3300 psi (225 bar). ALWAYS be
sure that all components and accessories have a maximum
working pressure of at least 3000 psi to avoid rupture
which can result in serious bodily injury including injection
and property damage.
NEVER leave a pressurized sprayer unattended to avoid
accidental operation of it which could result in serious
bodily injury.
ALWAYS follow the PRESSURE RELIEF PROCEDURE
whenever you stop spraying and before adjusting,
removing or repairing any part of the sprayer.
NEVER alter or modify any part of the equipment to avoid
possible component rupture which could result in serious
bodily injury and property damage.
NEVER use weak or damaged or non-conductive paint
hose. Do not allow kinking or crushing of hoses or allow it
to vibrate against rough or sharp or hot surfaces. Before
each use, check hoses for damage and wear and ensure
all uid connections are secure.
REPLACE any damaged hose. NEVER use tape or any
device to mend the hose.
NEVER attempt to stop any leakage in the line or ttings
with your hand or any part of the body. Turn off the unit
and release pressure by following PRESSURE RELIEF
PROCEDURE.
ALWAYS use approved high pressure ttings and
replacement parts.
ALWAYS ensure re extinquishing equipment is readily
available and properly maintained.
IMPORTANT: United States Government safety standards
have been adopted under the Occupational Safety & Health
Act. These standards, particularly the General Standards,
Part 1910, & the Construction Standards, part 1926 should
be consulted.
WHEN SPRAYING & CLEANING WITH FLAMMABLE
PAINTS OR THINNERS:
1. When spraying with ammable liquids, the unit must be
located a minimum of 25 feet away from the spraying
area in a well ventilated area. Ventilation must be
sufcient enough to prevent the accumulation of vapors.
2. To eliminate electrostatic discharge, ground the spray
unit, paint bucket and spraying object. Use only high
pressure airless hoses approved for 3300 psi which is
conductive.
3. Remove spray tip before cleaning gun and hose. Make
contact of gun with bucket and spray without the tip in a
well ventilated area, into the grounded steel bucket.
4. Never use high pressure in the cleaning process. USE
MINIMUM PRESSURE.
5. Do not smoke in spraying/cleaning area.
Reduce the risk of injection injury, static sparking or
splashing by following the specic cleaning procedure on
page 7 and 9.
ALWAYS follow the PRESSURE RELIEF PROCEDURE
on page 9.
ALWAYS remove the spray tip before ushing. Hold a
metal part of the gun rmly to the side of a metal pail and
use the lowest possible uid pressure during ushing.
NEVER use cleaning solvents with ash points below 140
degress F. Some of these are: acetone, benzene, ether,
gasoline, naphtha. Consult your supplier to be sure.
NEVER SMOKE IN THE SPRAYING/CLEANING AREA.
WARNING: Do not use halogenated solvents in this system.
The prime valve, 2 gun manifold and most airless guns have
aluminum parts and may explode. Cleaning agents, coatings,
paints or adhesives may contain halogenated hydrocarbon
solvents. DON"T TAKE CHANCES! Consult your material
suppliers to be sure. Some of the most common of these
solvents are: Carbontetrachloride, Chlorobenzene, Dichlo-
roethane, Dichloroethyl Ether, Ethylbromide, Ethylchloride,
Tethrachloethane. Alternate valves and guns are available if
you need to use these solvents.
AVOID COMPONENT RUPTURE
WARNINGS - CONTINUED
FLUSHING
GAS ENGINE PRECAUTIONS
Locate unit 25 feet away from spray area in well vent-
ilated area. NEVER operate in closed building unless
exhaust is piped outside. NEVER allow hose to lay
against engine mufers or hot parts. NEVER rell
fuel tank while engine is hot or is running.