Specifications

12
13
During use, especially with latex paint, high pressure will
cause the orice to grow larger. This destroys the pattern.
Replace tips before they become excessively worn. Worn
tips waste paint, cause overspray, make cutting-in difcult,
and decreases sprayer performance.
Two tips having the same tip size, but different pattern widths
will deliver the same amount of paint over a different area
(wider or narrower strip). A spray tip with a narrow pattern
width makes it easy to spray in tight places.
Thickness of the paint coat per stroke is determined by spray
tip "fan width", rate of the spray gun movement, and distance
to surface.
SPRAY TIP SELECTION
SPRAY TIP REPLACEMENT PATTERN WIDTH
SPRAY TIP SELECTION
Spray tip size is based on how many gallons of paint per
minute can be sprayed through the tip. Do not use a tip
larger than the maximum pump ow rate or capacity the
sprayer can accommodate. Pump ow rate is measured
in gallons per minute (GPM).
Spray tip selection is based on paint viscosity, paint type,
and job needs. For light viscosities (thin paints), use a
smaller tip; for heavier viscosities (thicker paints), use a
larger tip size.
Protected By U.S. Patent No. 6,264,115 Other U.S. & Foreign Patents Applied For.
For sizes not shown, call factory for availability.
SPRAY TIP - ORIFICE SIZE
(
Inches
)
(water @ 2000psi, 138 bar)
(latex paint @ 2000psi,
138 bar/1.36 spec. gr.)
*Pump will support tip worn to next larger size.
TIP IDENTIFICATION:
1st 3-digits identifies it as a REV-TIP
TM
for airless paint spraying
(P.N. 560-xxx) or
a REV-TIP
TM
for airless line striping
(P.N. 562-xxxST).
4th digit is the fan width - the number is half the fan width, e.g., 5 means a 10” fan.
5th and 6th digits are for the orifice size and is measured in thousandths of an inch,
e.g., 17 = 0.017 inch - The higher the number, the larger the tip.
Water Flow Rate (gpm)
.12 .18 .24 .31 .38 .47 .57 .67 .77 1.03 1.31 1.63 1.80
(lpm)
.49 .69 .91 1.17 1.47 1.79 2.15 2.54 2.96 3.90 4.98 6.17 6.81
Paint Flow Rate (gpm)
.10 .15 .21 .27 .33 .40 .49 .58 .66 .88 1.12 1.39 1.54
(lpm)
.38 .57 .79 1.02 1.25 1.51 1.85 2.20 2.50 3.33 4.24 5.26 5.83
Pump Minimum (gpm)
.25 .25 .33 .40 .50 .60 .75 .88 1.0 1.25 1.5 2.0 2.2
Output
*
(lpm)
1.0 1.0 1.25 1.5 1.9 2.3 2.8 3.3 3.8 4.7 5.7 7.5 8.2
Rev-Tip
TM
for Painting
Fan Width (12” from surface)
in. (mm) .009 .011 .013 .015 .017 .019 .021 .023 .025 .027 .031 .035 .039 .041
4-6 102-152 209 211 213 215 217 219 221 223 225 227 229
6-8 152-203 309 311 313 315 317 319 321 323 325 327 335
8-10 203-254 409 411 413 415 417 419 421 423 425 427 431
10-12 254-305 511 513 515 517 519 521 523 525 527 531 535
12-14 305-356 613 615 617 619 621 623 625 627 631 635 639 641
14-16 356-406 715 717 721 739 741
16-18 406-457 815 819 821 831
Gun Filter
C= Coarse - 60 mesh
F F F,C C C C C REMOVE FILTER
F= Fine - 100 mesh
Wood
Lacquer, Varnish
•
Interior
Stain, Sealer
•
•
Enamel
•
Wood
Exterior Stain
• •
Exterior
Vinyl, Acrylic, Latex
•
•
Masonry
Vinyl, Oil Base Alkyd
• •
Latex, Acrylic
•
• • •
Block Filler
• • • • •
• • •
Elastomer
•
•
•
• • • • •
Ceiling
Hi Build, Mil White
•
•
Structural Steel
Heavy Coatings
•
•
• • • • • •
.029
Rev-Tip
TM
for Painting
P.N. 560
-xxx
Rev-Tip
TM
for Striping
P.N. 562
-xxxST