Specifications

ManualsBrandsAIRLESSCO ManualsPaint SprayerProlight Contractor Series

XTEND-A-POLE SYSTEM

Tip Extensions - Complete with

Patented SPRAY CLEAN REV-GUARD

TIP EXTENSIONS, G-THREAD

032-170 6” Long 032-172 18” long

032-171 12” Long 032-173 24” Long

SWIVEL & EXTENSION, G-THREAD

032-035 Swivel only

032-184 Swivel with 36” Pole

EXTENSIONS (BARE POLES)

Add Tip Extension or Swivel Extension

to create desired length

032-053 24” Long

032-054 36” Long

Strong yet flexible, suitable

for use with airless spray

equipment up to 3300 PSI

Part No:

100-012 3/16” x 4’ Whip Hose

100-011 1/4” Hose, 50 Ft.

100-023 3/8” Hose, 50 Ft.

100-037 1/2” Hose, 50 Ft

100-219 Hose Cover Roll

100-010 1/4" Hose Connector

100-009 3/8" Hose Connector

For a complete listing of Airlessco Airless Accessories, see catalog # 001-357.

Standard Tip Extension

Swivel Extension

Bare Pole

For sizes not shown, call factory for availability.

SPRAY TIP - ORIFICE SIZE

(

Inches

)

(water @ 2000psi, 138 bar)

(latex paint @ 2000psi,

138 bar/1.36 spec. gr.)

*Pump will support tip worn to next larger size.

TIP IDENTIFICATION:

1st 3-digits

identifies it as a

REV-TIP

for airless paint spraying

(P.N.

560-xxx) or a

REV-TIP

for airless line striping

(P.N. 562-xxxST).

4th digit is the fan width - the number is half the fan width, e.g., 5 means

a 10” fan. Exception are the“W” prefix tips which indicate a wide spray

pattern.

5th and 6th digits

are for the orifice size and is measured in

thousandths of an inch, e.g., 17 = 0.017 inch - The higher the number,

the larger the tip.

Water Flow Rate

(gpm)

.12

.18

.24

.31

.38

.47

.57

.67

.77

1.03

1.31 1.63 1.80

(lpm)

.49

.69

.91

1.17

1.47

1.79

2.15

2.54

2.96

3.90

4.98 6.17 6.81

Paint Flow Rate

(gpm)

.10

.15

.21

.27

.33

.40

.49

.58

.66

.88

1.12 1.39 1.54

(lpm)

.38

.57

.79

1.02

1.25

1.51

1.85

2.20

2.50

3.33

4.24 5.26 5.83

Pump Minimum

(gpm)

.25

.33

.40

.50

.60

.75

.88

1.0

1.25

1.5

2.0

2.2

Output

(lpm)

1.0

1.25

1.5

1.9

2.3

2.8

3.3

3.8

4.7

5.7

7.5

8.2

Rev-Tip

for Painting

Fan Width

(12” from surface)

in.

(mm) .009

.011

.013 .015

.017

.019

.021

.023

.025

.027

.031

.035

.039

.041

4-6

102-152

209

211

213

215

217

219

221

223

225

227

229

6-8

152-203

309

311

313

315

317

319

321

323

325

327

335

8-10

203-254

409

411

413

415

417

419

421

423

425

427

431

10-12

254-305

511

513

515

517

519

521

523

525

527

531

535

12-14

305-356

613

615

617

619

621

623

625

627

631

635

639

641

14-16

356-406

715

717

721

739

741

16-18

406-457

815

819

821

831

20-24

508-610

W21

W23

W25

Gun Filter

C= Coarse - 60 mesh

F F,C

REMOVE FILTER

F= Fine - 100 mesh

Wood

Lacquer, Varnish

•

Interior

Stain, Sealer

•

Enamel

•

Wood

Exterior Stain

•

Exterior

Vinyl, Acrylic, Latex

•

Masonry

Vinyl, Oil Base Alkyd

•

Latex, Acrylic

•

Block Filler

•

Elastomer

•

Ceiling

Hi Build, Mil White

•

Structural Steel

y C

•

.029

REV-TIP

For Paint Spraying

P.N. 560-xxx

Includes Rev-Tip

Metal Seal & O-Ring Seal.

560-517

REV-TIP

Orifice Size

1/2 Fan Width

Sample:

REV-GUARD

Part # 561-002

7/8-14 “G” thread. Some: Graco, Wagner, Titan, Airlessco.

REV-TIP

SPRAY TIP SIZE CHART

Part Number

560-xxx

Fine Finish

Tips Below!

Fine Finish

REV-TIP

Part # 571-xxx

Fan Width Orifice Size

Inches (mm) .010 .012 .014

4-6 102-152 210 212 214

6-8 152-203 310 312 314

8-10 203-254 410 412 414

Double orifice design for lower pressure spraying

when you need a smoother finish on interior trim,

cabinetry, shutters, and doors.

• Aerodynamics

eliminates drips

• Super compact

Part # 561-001

11/16-16 “F” Thread. Fits:

Airlessco, and some ASM,

Wagner, and Campbell Hausfeld.

Fine Finish

Part # 571-x

NEW!

HIGH PRESSURE HOSE