Specifications

12
13
REV-TIP
™
SIZE SELECTION CHART
PATTERN WIDTH
Thickness of the paint coat per stroke is determined by
spray tip "fan width", rate of the spray gun movement, and
the distance to the surface being sprayed. Airlessco "Wide
Pattern" spray tips offer fan patterns up to 18-24" wide for
optimum coverage speed. Due to the ne atomization at
the edge of the spray pattern on Wide Pattern tips, they
may not be the best choice for exterior use when wind
is present.
SPRAY TIP SELECTION
Two tips having the same tip size, but different pattern
widths will deliver the same amount of paint over a different
area (wider or narrower strip). A spray tip with a narrow
pattern width makes it easy to spray in tight places.
SPRAY TIP REPLACEMENT
During use, especially with latex paint which is very
abrasive, high pressure will cause the orice to grow larger.
This destroys the spray pattern. Replace tips before they
become excessively worn.
Worn tips waste paint, cause overspray, make cutting-in
difcult. They can effect sprayer performance too because
the volume of paint going thru a "blown out" tip can be
greater than the pumps maximum output capacity.
Spray tip selection is based on paint viscosity, paint
type, your pumps output capabilities, and job needs.
For light viscosities (thin paints), use a smaller tip;
for heavier viscosities (thicker paints), use a larger
tip size.
Going to larger spray tip sizes is dependent on how many
gallons of paint per minute can be sprayed by your pump
Do not use a tip larger than the maximum pump ow rate
or capacity the sprayer can accommodate. Pump ow
rate is measured in gallons per min. (GPM), or where
appropriate, liters per min. (LPM).
SPRAY PAINTING TIP - ORIFICE SIZE
(
Inches
)
(water @ 2000psi, 138 bar)
(latex paint @ 2000psi,
138 bar/1.36 spec. gr.)
*Pump will support tip worn to next larger size.
Water Flow Rate
(gal./min.)
.12 .18
.24 .31 .38
.47 .57
.67
.77
1.03 1.31 1.63
1.80
(liters/min.)
.49 .69
.91 1.17
1.47 1.79 2.15
2.54 2.96
3.90 4.98 6.17
6.81
Paint Flow Rate
(gal./min.)
.10
.15
.21 .27
.33 .40
.49
.58
.66
.88
1.12
1.39
1.54
(liters/min.)
.38
.57
.79
1.02 1.25
1.51 1.85
2.20
2.50 3.33
4.24
5.26
5.83
Pump Minimum
(gal./min.)
.25
.25
.33 .40
.50 .60 .75 .88
1.0 1.25
1.5 2.0 2.2
Output
*
(liters/min.)
1.0
1.0
1.25 1.5
1.9 2.3 2.8 3.3
3.8
4.7 5.7 7.5 8.2
REV-TIP
TM
for Painting
Fan Width
(12” from surface)
in.
(mm)
.007
.009 .011
.013
.015
.017 .019
.021
.023 .025
.027
.031 .035
.039 .041
4-6 102-152
209
211
213
215
217 219
221 223
225 227
229
6-8 152-203
307 309 311 313
315
317
319
321 323 325 327
335
8-10 203-254
409 411 413
415 417 419 421
423 425
427 431
10-12
254-305
511 513 515 517
519
521
523 525 527
531 535
12-14
305-356
611
613
615 617 619
621 623
625 627
631 635 639
641
14-16
356-406
715 717
721
739
741
16-18
406-457
815
819 821
831
20-24
508-610
W21
W23
W25
Gun Filter
C = Coarse
F
F F F,C C
C
C C C REMOVE FILTER
F= Fine
Wood
Lacquer, Varnish
•
•
Interior
Stain, Sealer
•
•
•
Enamel
•
•
Wood
Exterior Stain
•
•
Exterior
Vinyl, Acrylic, Latex
•
•
Masonry
vinyl,oil-base
alkyd
•
•
Latex, Acrylic
•
•
•
•
Block Filler
• •
• •
•
• • •
Elastomer
•
•
•
• •
• • •
Ceiling
Hi Build, Mil White
•
•
Structural Steel
Heavy Coatings
•
•
•
•
•
•
•
•
.029
NEW WIDE PATTERN REV-TIP ►