Wireless N 300 Gigabit Green Router Model # AR695W User’s Manual Ver.
Copyright Copyright © Airlink101, 2010. The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system, translated into any language, or transmitted in any form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the prior written permission. Trademarks All products, company, brand names are trademarks or registered trademarks of their respective companies.
Table of Contents CHAPTER 1 PRODUCT INFORMATION..............................................................................................................1 1.1 INTRODUCTION AND SAFETY INFORMATION .........................................................................................................1 1.2 PACKAGE CONTENTS ...........................................................................................................................................2 1.3 FAMILIAR WITH YOUR NEW GIGABIT ROUTER ..
3.4.7 Schedule Rule............................................................................................................................................83 3.5 TOOLBOX ...........................................................................................................................................................85 3.5.1 View Log....................................................................................................................................................86 3.5.
Chapter 1 Product Information 1.1 Introduction and safety information Congratulations on your purchase of the Airlink101® AR695W Wireless N 300 Gigabit Green Router. This Router is recommended to be used with AirLink101® Wireless N 300 products to provide the best performance. The high bandwidth combined with extended wireless coverage delivers fast and reliable connections for all of your networking applications. The built-in gigabit switch highly increases the wired Ethernet speed.
1.2 Package Contents Before you start using this router, please check if there’s anything missing in the package, and contact your dealer of purchase to claim for missing items: 1. 2. 3. 4. 5. 6.
1.3 Familiar with your new Gigabit Router A. Front Panel LED Status Description Status Blinking (Green) Device status is working properly. On (Green) Router is on. Off Router is at power saving mode.
B. Back Panel Item Name Description Antennas These antennas are detachable 3dBi dipole antennas. ON/OFF Switch on/off the router. 1-4 Local Area Network (LAN) ports 1 to 4. WAN Wide Area Network (WAN / Internet) port. PWR Power connector, connects to A/C power adapter.
Chapter 2 Configure the Router 2.1 Connect the Router to your network Note: Prior to connecting the router, be sure to power off your computer, DSL/Cable modem, and the router. Step 1 Connect one end of a network cable to the WAN port of the router and connect the other end of the cable to the DSL/Cable modem. Step 2 Power on the modem. Step 3 With another network cable, connect one end of the cable to your computer’s Ethernet port and connect the other end to one of the LAN ports of the router.
Step 4 Plug the power adapter to the router and connect it to an electrical outlet. Make sure the power switch at the back is “On”. Step 5 Power on your computer. Step 6 Check LEDs of the router: make sure Status, WAN, Wireless, and the LAN port that the computer is connected to are lit.
2.2 Configure the Router with EZ Setup Wizard Step 1 Insert the Setup CD into CD-ROM drive. Step 2 When the autorun menu pops up, click EZ Setup Wizard. Note: If the autorun menu does not show up on your monitor, please go to Computer Æ CDROM drive Æ Wizard, and execute “EZWizard.exe”.
Step 3 Select your language and click Next. Step 4 Click on Wizard.
Step 5 Please make sure your computer is connected to the LAN port of the router, and your modem is connected to the WAN port of the router. Step 6 Click Next to configure the basic wireless settings.
Step 7 Configure the SSID (wireless network name, i.e. myHome), Channel, Security and Key. It is suggested to select WPA2-PSK for best wireless security. Enter 8~63 characters into Key box, then click Next. Step 8 Click Next and the wizard will detect your WAN settings, or you can select your WAN type manually by checking “Let me select WAN service by myself”.
Step 9 Enter the settings based on your WAN service type. Cable (Dynamic IP) If you are using cable Internet service, your WAN type is “Dynamic IP”. You do not need to configure anything here, then click Next to continue. DSL (PPPoE or Dynamic IP) For DSL users, your WAN type is either PPPoE or Dynamic IP. You can try both types and determine which one works for you.
For PPPoE settings, please enter the username and password provided by your ISP (Internet Service Provider). Note: Depending on the ISP, you may need to include the domain name with your username. Example: username@sbcglobal.net Step 10 Verify the settings you have configured. Click Next to save the settings and reboot the router. This will take about 30 seconds.
Step 11 Click Next to test the Internet Connection, or you can ignore the test, just open the Internet browser and verify if you are connected to the Internet. If you cannot connect to the Internet, please go to Section 4, Troubleshooting. Step 12 After the WAN service test completed, click Finish. The wizard will open the web configuration page for the router automatically unless you uncheck the checkbox below “Open the default web browser to access the advanced configuration”.
You will see the status of the router on the web configuration page brought up by the web browser. Valid numbers should be assigned to IP Address, Subnet Mask and Gateway, instead of all 0’s.
2.3 Configure the Router with Web Configuration Utility Another approach to configure the router is using the Wizard in the Web Configuration Utility. The wizard will guide you setting up the basic settings of this router. You do not need to go through the wizard again if you have finished 2.2 Configure the Router with EZ Setup Wizard. In order to enter the Web Configuration Utility, you need to first log in to the router from your web browser.
16
Step 4 Click Next to start the Setup Wizard. Step 5 Change System Password. Enter the current password, new password and reconfirm the new password. (The default password is ‘admin’.) If you do not wish to change the password, please leave all fields blank. Click Next.
Step 6 Select Auto Detecting WAN Type to let the wizard detect which Internet connection you use or select Setup WAN Type Manually to select the Internet connection type manually. Click Next. If you select Setup WAN Type Manually, please specify a WAN type you are using. For Cable Users: Please select Obtain an IP address from ISP automatically (Dynamic IP Address).
Address) or Some ISPs require the use of PPPoE to connect to their services (PPP over Ethernet) depending on the type of modem provided by your ISP (Internet Service Provider). You can try both settings and determine which one works for you. Click Next. Step 7 Configure the WAN settings according to the WAN type you selected. Dynamic IP Address: Click on Clone MAC.
PPP over Ethernet: Enter the Account and Password provided by your ISP. Note: Depending on the ISP, you may need to include the domain name with your username. Example: username@sbcglobal.net Step 8 Keep the default SSID (wireless network name) or change it to a desired name, so you can always recognize your wireless network with it, for example ‘myHome’. Select a channel number for your wireless network. Click Next.
Step 9 Set up Wireless Security for your router. It is recommended to select WPA2-PSK (AES) for security to protect your wireless network from unauthorized users. Type in 8~63 characters into Preshare Key. Click Next. WPA2-PSK (AES) is the most secured encryption mode for general users but some older wireless adapters might not support it. Therefore, please make sure all wireless devices on your network support this security type.
Step 10 Verify the information you have configured. If everything is correct, click Apply Settings to save the settings and reboot router. Step 11 When you see window like below, you are successfully connected to the Internet. Click Finish. Congratulations! Your router configuration has been finished. Please go to 2.4 Connect to the Router Wirelessly.
2.4 Connect to Router Wirelessly You must configure your wireless computer in order to establish a wireless connection to the router. In this section, you can find the instructions of how to connect to the router wirelessly with your Windows 7 computer. You can also refer to the manual of your wireless device on how to connect to the router. Step 1 Click on the wireless icon in the system tray on your desktop. A list of available network will pop up. Select the one you want to connect to and click Connect.
Step 2 Enter the key you configured for the router if you have enabled the wireless security, then click OK. The wireless connection should be now established.
Chapter 3 Advanced Configuration You can make advanced configurations on this router through Web Configuration Utility to meet your network’s needs, such as: Virtual Server, Access Control, Network Security, etc. If you have already gone through the Setup Wizard, you do NOT need to configure anything here for you to start using the Internet. In order to enter the Web Configuration Utility of your router, you need to first log in to the router from your web browser.
26
3.1 Basic Setting You can configure LAN, Internet connection type, DHCP, wireless settings and system password for the router in this page.
3.1.1 Primary Setup This page allows you to specify an IP address for your router, and configure the Internet connection settings. Parameter Description LAN IP Address The local IP address of this router. You can change it if necessary. WAN Type Displaying the current WAN (Wide Area Network , i.e. Internet) connection type you configured for the router. Click “Change” to modify. Please see Section 3.1.1.1. If you are not sure which WAN type you are using, please contact your ISP.
Select a WAN type from the list and click Save. A. Static IP Address: Click on Static IP Address if your ISP (Internet Service Provider) has provided you a set of IP addresses for your Internet connection. B. Dynamic IP Address: Click on Dynamic IP if you are connecting to Internet through a cable modem. C. Dynamic IP Address with Road Runner Session Management: This setting only works when you are using Telstra Big Pond’s network service in Australia. D.
A) Static IP Address Enter the WAN IP address, WAN Subnet Mask, WAN Gateway, Primary DNS , and Secondary DNS addresses provided by your ISP. After you finished all settings, click Save to save the settings and click Reboot. The change will take effect after rebooting the router.
Parameter Description Host Name Please input the host name of your router; this is optional and only required if your service provider asks you to do so. WAN’s MAC Address Please input MAC address of your computer here if your ISP only permits computer with certain MAC address to access Internet. If you are using the computer which used to connect to Internet via cable modem, you can simply press ‘Clone MAC’ button to fill the WAN’s MAC address field with the MAC address of your computer.
C) Dynamic IP Address with Road Runner Session Management: Please enter the account and password provided by your Telstra Big Pond ISP. Parameter Description Account Please input user name of your account assigned by Telstra. Password Please input the password assigned by Telstra. Login Server Please input the IP address of login server here. (Optional) After you finished all settings, click Save to save the settings and click Reboot. The change will take effect after rebooting the router.
D) PPP Over Ethernet (PPPoE) Parameter Description PPPoE Account Enter the User Name for your DSL account, you can obtain this information from your ISP. PPPoE Password Enter the Password for your DSL account, you can obtain this information from your ISP. Primary DNS This feature allows you to assign a Primary DNS Server. You can obtain this information from your ISP. If your ISP does not provide this information, you can leave it blank.
to the ISP after the connection is established. Manually: Router will not connect to the ISP until user clicks the Connect button on the Status-page. PPPoE Service Name Enter the DSL service company. This is optional. Assigned IP Address Input the IP address you wish to use. This is optional. MTU (Maximum Transmission Unit) The most common MTU value is 1492. You can configure it as your ISP suggested. After you finished all settings, click Save to save the settings and click Reboot.
Parameter Description IP Mode Select the type of how you obtain IP address from your service provider here: Static IP Address or Dynamic IP Address. My IP Address Enter the IP address assigned by your ISP if you select Static IP Address. My Subnet Mask Enter the Subnet Mask assigned by your ISP if you select Static IP Address. Gateway IP Enter the Gateway IP address assigned by your ISP if you select Static IP Address. Server IP Address/Name Enter the IP address of the PPTP server.
E) L2TP Parameter Description IP Mode Select the type of how you obtain IP address from your service provider here: Static IP Address or Dynamic IP Address. My IP Address Enter the IP address assigned by your ISP if you select Static IP Address. My Subnet Mask Enter the Subnet Mask assigned by your ISP if you select Static IP Address. Gateway IP Enter the Gateway IP address assigned by your ISP if you select Static IP Address. Server IP Address/Name Enter the IP address of the L2TP server.
session. Set it to zero or enable “Auto-reconnect” to disable this feature. Connection Control There are 3 modes for you to control the Internet connection: Connect-on-demand: Router will connect to the ISP when its client sends outgoing packets. Auto Reconnect (Always-on): Router will keep the connection to the ISP after the connection is established. Manually: Router will not connect to the ISP until user clicks the Connect button on the Status-page.
3.1.2 DHCP Server This page allows you to configure the DHCP settings for your router. Parameter Description DHCP Server Select Disable or Enable the DHCP server. Lease Time DHCP lease time to the DHCP client. Please enter a number between 5 to 10080. 10080 Minutes = 7 days. IP Pool Starting/Ending Address Whenever there is a request from a network client, the DHCP server will automatically allocate an unused IP address from the IP address pool to the requesting computer.
Primary DNS/Secondary DNS This is optional. This feature allows you to assign a Primary / Secondary DNS Server. Primary WINS/Secondary WINS This is optional. This feature allows you to assign a WINS Server. Gateway This is optional. Gateway address can be the IP address of an alternate Router. Client List Click on Client List to view DHCP clients. Click Save to save the settings you made.
3.1.3 Wireless You can set parameters that are used for wireless clients to connect to this router. The parameters include SSID, Channel Number, Encryption etc. Parameters Default Description Wireless Enable Enable or disable wireless function. Wireless On/Off by Time schedule Disable Select a pre-defined schedule rule from the drop-down menu (click on Schedule Setting to add a new rule) and select Enable, then the router will turn on/off wireless function according to the schedule rule.
routers in the same area. It’s recommended to change default SSID value to the one which is meaningful to you, like myhome, office_room1, etc. Wireless Mode 11b/g/n mixed Please select the wireless mode from one of the following options: 11b/g/n mixed: 2.4GHz band, allows 802.11b, 802.11g, and 802.11n wireless network clients to connect to this router (maximum transfer rate 11Mbps for 802.11b clients, maximum 54Mbps for 802.11g clients, and maximum 300Mbps for 802.11n clients*). 11g Only: 2.
Configuring Security - WEP Note: IEEE802.11n only supports WPA2-PSK or WPA-PSK AES encryption. If you use WEP as your encryption, wireless data rate will drop to 54Mbps (802.11g standard). Key Mode: Select HEX or ASCII. You can select ASCII (alphanumeric format) or Hexadecimal (in the “a~f” and “0~9” range) for the key format. WEP: Key 1~4: Select 64 bits or 128 bits key length. Select a WEP Key you wish to use and enter key value.
communication, so the encryption key is not easy to be broken by hackers. This can greatly improve your wireless security.WPA2-PSK AES is the most secured setting for general users. Security: Encryption: Select WPA-PSK or WPA2-PSK Select either AES or TKIP. It is suggested to select AES if all your wireless computers / devices support this encryption mode. Note: IEEE802.11n only supports AES encryption. If you use TKIP as your encryption, wireless data rate will drop to 54Mbps (802.11g standard).
Encryption Key Length: You can select either 64 bits or 128 bits. RADIUS Server IP: The RADIUS server's IP address. RADIUS port: The RADIUS server's service port. RADIUS Shared Key: Key value shared by the RADIUS server and this router. This key value should be consistent with the one in the RADIUS server. Configuring Security - WPA / WPA2 Wi-Fi protected Access (WPA) is designed to improve data protection and implement access control for Wireless LAN system.
RADIUS port: The RADIUS server's service port. RADIUS Shared Key: Key value shared by the RADIUS server and this router. This key value should be consistent with the one in the RADIUS server. After you finished all settings, click Save to save the settings and click Reboot. The change will take effect after rebooting the router. 3.1.3.1 WDS The Wireless Distribution System (WDS) provides wireless point-to-point, and point-to-multipoint bridging for deployment over large area.
Before you set up WDS bridging: 1) Make sure your wireless computer can associate with individual router/AP. 2) Configure the same channel for every router/AP. 3) Configure a unique different SSID for every router/AP in order to distinguish each unit on your wireless LAN. 4) Configure a static IP address for every router/AP. Make sure all IP addresses are based on the same subnet mask, and out of your DCHP client range. Parameters Description AP Mode AP Only: WDS function is disabled.
3.1.3.2 WPS (Easy Setup Button) The AR695W Wireless N 300 Gigabit Green Router has a built-in Easy Setup Button (WPS) which allows you to build secured wireless connection between your wireless computers and the router quickly and easily. Please make sure your wireless device support this feature as well. If not, you will need to set up the wireless security manually and you can skip this section.
Step 3 Within the following 2 minutes, push the WPS Button on the Router and hold for 1 second. The wireless LED will start blinking quickly. Step 4 The Router will now start the handshake with the wireless adapter which will take about 30 seconds. When you see the window similar to the one below, the connection has been established.
To configure the WPS settings of the router, go to Advanced > Basic Setting > Wireless, then click on WPS button. There are two methods to activate WPS – PIN and PBC.
enter the PIN generated by the wireless client computer into Enrollee PIN, and click Trigger button to start WPS. 2) PBC (Push Button Configuration) You can choose to press the hardware button on the front panel of the router, or select Configure Wireless Station, Software button, and click Trigger button to start WPS. Parameters Description WPS Select Enable or Disable WPS function.
WPS State It displays “Idle” when there is no WPS session going on, “Processing” when WPS is in progress, or “Complete” when WPS is finished. WPS Status It displays “Configured” if WPS setup is successful, or “Unconfigured” if WPS setup fails. Click Save after you finished all settings. 3.1.3.3 Wireless Client List This table displays the wireless clients that are currently associated to the router. You can click Back to go back to the Wireless page, or click Refresh to refresh the list.
3.1.4 Change Password You can change the password required to log in to the Router’s web configuration utility. The default password is “admin”. It is suggested to change the administrator’s default password as soon as you start to use the Router, and store it in a safe place. The password consists of 0 to 9 alphanumeric characters, and is case sensitive Parameters Description Old Password Enter the current password of the router. New Password Enter the new password.
3.2 Forwarding Rules 3.2.1 Virtual Server If you want to host a HTTP/FTP server or allow remote access to your IP camera on the LAN from the Internet, you must set up port forwarding rules on the router in order to direct incoming traffic to the server or IP Camera. This page allows you to set up to 20 port forwarding rules for the specified applications.
Protocol This is the protocol type to be forwarded. You can choose to forward “TCP” or “UDP” packets only or select “Both” to forward both “TCP” and “UDP” packets. Enable Check to enable this forwarding rule. Schedule Rule# Enter a Schedule Rule number to enable the forwarding rule only within the desired time frame. Please refer to 3.4.7 Schedule Rule for detailed setting instructions. You can set 0 to enable the forwarding rule always.
3.2.2 Special Applications Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications cannot work when Network Address Translation (NAT) is enabled. If you need to run applications that require multiple connections, specify the port normally associated with an application in the “Trigger” field, then enter the public ports associated with the trigger port to open them for inbound traffic.
Note: Only one PC can use each Special Application tunnel at same time. If the mechanism of Special Applications fails to make an application work, try setting your computer as the DMZ host instead. Click Save after you finished all settings. 3.2.3 Miscellaneous If you have a local client PC that cannot run an Internet application (e.g. Games) properly from behind the NAT firewall, then you can open the client up to unrestricted two-way Internet access by defining a DMZ Host.
Super DMZ (IP Passthrough) Select Super DMZ when your computer or server on the Local Area Network needs to allow access from the Internet with a real public IP address. With IP Passthrough configured, all IP traffic, not just TCP/UDP, is forwarded back to the host computer. This can be necessary with certain types of software that do not function reliably through Network Address Translation. Non-standard FTP Port Enter the FTP port number if the FTP server’s port you try to access is not 21.
3.3 Security Setting This function allows you to configure Internet access rules for your local computers based on the IP address, MAC address, URL or keywords. 3.3.1 Packet Filtering Packet Filtering allows you to control access to a network by analyzing the incoming and outgoing packets and letting them pass or halting them based on the IP address of the source and destination.
Computers with IP addresses between 192.168.2.20 to 192.168.2.50 have no restriction on accessing any network services, while others computers are all blocked. Meanwhile, computers with IP addresses between 192.168.2.100 to 192.168.2.199 are allowed to send Email (port 25), receive E-mail (port 110), and browse Internet (port 80). For each rule, you can define: • • • • Source IP address Destination IP address Destination port address Protocol: TCP or UDP or both.
Port Please input the port number here. You can define a single port (80) or a range of ports (1000-1999). Add prefix "T" or "U" to specify TCP or UDP protocol, for example, T80, U53, U2000-2999. No prefix indicates both TCP and UDP are defined. Leaving this field blank indicates all ports. Enable Check/uncheck Enable to enable/disable each Packet Filtering rule. Schedule Rule# Enter a Schedule Rule number to activate the filtering rule only within the desired time frame. Please refer to 3.4.
3.3.2 Domain Blocking You can block users from accessing specific domains on the internet. This feature can help parents to manage the Internet usage for their children (i.e. Parental Control). Parameter Description Domain Filter Check/Uncheck Enable to enable/disable Domain Filter. Log DNS Query Check/Uncheck Enable to enable/disable logging DNS Query. Privilege IP Address Range Enter an IP address range that has privilege to access any network service without restriction.
Link request to xyz.com will be dropped and recorded in log file. Link request to www.abc.com will be allowed but will be recorded in log file. Link request to msn.com will be dropped and will not be recorded in log file. However, IP Address from 192.168.2.10 to 192.168.2.20 will not be restricted. Enable Schedule Rule# Check/Uncheck Enable to enable/disable each rule individually. Enter a Schedule Rule number to activate the filtering rule only within the desired time frame. Please refer to 3.4.
3.3.3 URL Blocking You can block access to certain websites or web contents from local PCs by entering a full URL address or just keywords. The major difference between “Domain Filter” and “URL Blocking” is that Domain Filter requires user to input a suffix (like .com or .org, etc), while URL Blocking requires user to input a keyword only. In other words, Domain Filter can block specific websites, while URL Blocking can block any website that contains the specific keyword.
Rule for detailed setting instructions. Set 0 to let the filtering rule always take effect. Click on Save after you finished all settings. 3.3.4 Internet Access Control MAC Access Control will help you to prevent unauthorized users from connecting to your wireless router. Only those network devices with MAC addresses you specified here are allowed to access your wireless router.
drop-down list and select an ID, click “Copy to”. The MAC address of the computer you selected will be automatically filled into the specific ID. Make sure the Enable box is checked. Click on Save after you finished all settings. This router offers 3 types of Internet Access Control: • MAC Address Control: allow or deny Internet access from specific MAC address. See 3.3.4.1.
3.3.4.1 MAC Address Control This feature allows you to control Internet access based on MAC address and time schedule. Parameters Description MAC Access Control Check this box to enable the MAC filtering function. All settings in this page will take effect only when Enable is checked. Connection Control Check this box to enable the rule that wireless or wired clients whose MAC addresses are in the table can connect to the router.
DHCP Clients Select a DHCP client from the drop down list. Select an ID number and click Copy To. The client’s MAC address will be copied to the ID you selected; you do not need to enter it manually. MAC Address Input the MAC address of your computer / network device. C Check this box to allow the wired/wireless client connecting to the router. A Check this box to allow the wireless client associating to the wireless network. Previous / Next You can set up to 32 MAC control rules for this router.
3.3.4.2 Group MAC Access Control This feature allows you to define user groups and map them with schedule control to allow Internet access within specific time frame. In the example below, two groups have been added with different schedule rule: Group List 1 has two computers with Schedule Rule 1. The two computers in Group 1 can only access network within the time frame of Schedule Rule1. Under the group list, you can modify Schedule 1 by clicking on Modify Schedule 1 (see section 3.4.
1. Enter MAC address manually or select one from the DHCP client list, and click “<
Schedule Rule Select a Schedule Rule from the drop-down list. Please refer to 3.4.7 Schedule Rule for detailed setup instructions. Deny Check/Uncheck Deny to deny/allow network access from an Interface within the selected schedule rule. Click on Save after you finished all settings. 3.3.5 Miscellaneous Parameters Description Remote Administrator Host/ Port This feature enables you to perform administration task from remote host.
period of time. You may set the time-out period to zero to disable this feature. Discard PING from WAN side Check this box to enable Discard PING from WAN side. When you enable this feature, your router will not respond to a “ping” request from any host on the WAN side. SPI Mode Stateful Packet Inspection mode is a firewall that keeps track of the state of network connections (such as TCP, UDP communication) travelling across it.
3.4 Advanced Setting This page allows you to set up system time, log, DDNS, routing, QoS, schedule rule, and other advanced settings. 3.4.1 System Time Specify correct system time for your router is very important. It will affect the schedule rule and system logs. This router provides 3 ways to configure the system date and time: 1) Synchronize with time server. (The router must connect to the Internet.) > Select Get Date and Time by NTP Protocol 2) Synchronize with PC.
Parameter Description System Time Displaying the current system time of router. Sync Now Click this button to synchronize the system time with the desired time server. (The router must be connected to the Internet to be able to synchronize time.) Time Server Select a time server here. Time Zone You can select your local time zone here. The router will synchronize time according to your time zone selection.
3.4.2 System Log You can enable this function to log all important system events for your router. This page supports two methods to export system logs to specific destination by means of syslog (UDP) and SMTP (TCP). Parameters Description IP Address of Syslog Server Enter the host IP of destination where system log will be sent to. Check Enable to enable this feature Email Alert Check Enable if you want to enable Email alert (send syslog via Email).
you do not specify port number, the default value is 25. For example, "mail.abc.com" or "192.168.1.100/25". Email Addresses Enter the Email addresses of the recipients who will receive these logs. You can assign more than 1 recipient by using ';' or ',' to separate these Email addresses. Email Subject The subject of email alert, this setting is optional. Username Input the user name of the Email account. Password Input the password of the Email account.
3.4.3 Dynamic DNS Parameter Description DDNS Select Disable or Enable DDNS function. Provider A DDNS provider provides service for you to bind your IP (even private IP) with a certain Domain name. Choose a desired provider. Provider Website Click Provider Website to go to the selected DDNS provider’s website. Host Name You can register a domain name at the DDNS provider’s website. The full domain name is concatenated with host name (you specify) and a suffix (DDNS provider specifies).
3.4.4 QoS Rule Quality of Service provides an efficient way for computers on the network to share the Internet bandwidth with a promised quality of Internet service. Without QoS, all computers and devices on the network will compete with one another to get Internet bandwidth, and some applications which require guaranteed bandwidth (like video streaming and network telephone) will be affected; therefore, an unpleasing result will occur, like interruption of video / audio streaming.
Remote IP Address Specify a remote (destination) IP address that will be affected by this rule. Ports Please input the range of remote (destination) port number that will be affected by this rule. If you want to apply this rule on port 80 to 90, please input “80-90”; if you want to apply this rule on a single port, just input the port number, such as 80. If the remote (destination) IP address and /or port number is universal, just leave it blank.
3.4.5 SNMP Parameter Description Enable SNMP You must check either Local or Remote or both to enable SNMP function. If Local is checked, this device will response request from LAN. If Remote is checked, this device will response request from WAN. Get Community Setting the community of GetRequest your device will response. Set Community Setting the community of SetRequest your device will accept. IP 1~4 Input your SNMP Management PC's IP here.
3.4.6 Routing Routing Table allows you to determine which physical interface address to use for outgoing IP data grams. If you have more than one routers and subnets, you will need to enable routing table to allow packets to find proper routing path and allow different subnets to communicate with each other. For static routing, you can specify up to 8 routing rules.
For Example: AR695W Configuration on Static Routing Destination Subnet Mask Gateway Hop Enabled 192.168.1.0 255.255.255.0 192.168.123.216 1 √ 192.168.0.0 255.255.255.0 192.168.123.103 1 √ When Client3 wants to send an IP data gram to 192.168.0.2, it will use the above table to determine that it has to go via 192.168.123.103 (a gateway), and if it sends packets to 192.168.1.11, it will go via 192.168.123.
Static Routing Select Enable or Disable to enable or disable Static Routing function. Destination Enter a destination IP address. The Destination IP is the address of the remote network or host to which you want to assign a static route. Subnet Mask Enter the subnet mask. The Subnet Mask determines which portion of a Destination IP address is the network portion, and which portion is the host portion. Gateway Enter the gateway IP address.
3.4.7 Schedule Rule You can configure schedule rules to control the time frame of network access. Parameter Description Schedule Check or uncheck Enable to enable or disable the schedule rule. Rule# Displaying rule numbers. Rule Name Displaying rule names that have been added to the schedule rule table. Action Click on Edit to modify the schedule rule or Delete to remove the rule from the schedule rule table. Add New Rule Click on Add New Rule to add a new rule to the schedule rule table.
3.4.7.1 Add New Rule You can add a new schedule rule in this page. Parameter Description Name of Rule# Enter a name for the new rule. System Time Displays the current system time of the router for you to verify if this matches with the date/time of where you are located. You can see 3.4.1 on how to modify the system time. Week Day You can set time schedule for each day or everyday. Start Time/End Time (hh:mm) Enter the start and end time of a time schedule.
3.5 Toolbox The Toolbox page allows you to view system logs, upgrade firmware, save/reload configuration settings, reset factory default settings, reboot the router, and perform ping test.
3.5.1 View Log You can view, download, and clear the system logs stored in the router here.
3.5.2 Firmware Upgrade You can view the current firmware version of router in this page. To upgrade the firmware for the router, you must use a computer that is wired connected to the router. Firstly, you need to download the firmware from www.airlink101.com and save it to your local hard disk first. You may need to unzip it if it is a .zip file. Click on Browse to select the firmware you just downloaded/unzipped, then click Upgrade to start the upgrade process.
3.5.3 Backup Setting You can save the router’s configuration settings to your local hard disk by clicking on Backup Setting and save it as a .bin file. Once you need to restore the settings, please go to Firmware Upgrade page and load the .bin file you saved. 3.5.4 Reset to Default To restore the router settings to factory default, click on Reset to Default, and you will be prompted: Click OK to continue or Cancel to exit.
3.5.5 Reboot To reboot the router, click on Reboot, and you will be prompted: Click OK to continue or Cancel to exit. 3.5.
Parameter Description MAC Address for Wake-on-LAN Wake-on-LAN is a technology that enables you to power up a networked device remotely. In order to use this feature, the target device must be Wake-on-LAN enabled and you have to know the MAC address of this device. Enter the MAC address of the device and click Wake Up. The router will send wake-up frame to the target device immediately and the device can be powered up remotely. Domain Name or IP Address for Ping Test Enter an domain name (i.e. google.
Chapter 4 Status The Status section allows you to monitor the current status of your router. You can use the Status page to monitor: the Internet connection, Wireless, NAT status, and the statistics information of the Router.
4.1 System Status You can view the status of current Internet connection. By clicking Renew and Release, you can renew and release the WAN IP address obtained from the ISP (Internet Service Provider). 4.2 Wireless Status You can view the Wireless LAN status of your router, including SSID (the name of your wireless network), Channel number, Security, and Wireless MAC address of the router.
4.3 Statistics Information You can view the statistics information of your router, including inbound and outbound packets. 4.4 NAT Status Click NAT Status on the bottom of the Status page to view NAT Status.
Chapter 5 Appendix 5.1 Hardware Specification Standards • • System Requirement IEEE 802.11b / g / n IEEE 802.3, 802.3u, 802.
Technical Support E-mail: support@airlink101.com Toll Free: 1-888-746-3238 Website: www.airlink101.com *Theoretical maximum wireless signal rate derived from IEEE standard 802.11 specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, mix of wireless products used, radio frequency interference (e.g.
