AirVideo-100v2 Wireless Presenter Dongle User’s Manual i AirLive WL-1700USB User’s Manual
Copyright and Disclaimer Copyright & Disclaimer No part of this publication may be reproduced in any form or by any means, whether electronic, mechanical, photocopying, or recording without the written consent of OvisLink Corp. OvisLink Corp. has made the best effort to ensure the accuracy of the information in this user’s guide. However, we are not liable for the inaccuracies or errors in this guide. Please use with caution.
Copyright and Disclaimer FCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Table of Contents Table of Contents 1. Introduction ............................................................................................... 1 1.1 Overview ............................................................................................... 1 1.2 Features ................................................................................................ 5 1.3 Packing List.......................................................................................... 5 1.4 Specification Table......
Table of Contents 3. Smart phone ............................................................................................ 42 3.1 Introduce............................................................................................. 42 3.2 PtG converter ..................................................................................... 42 3.2.1 PtG Converter ..............................................................................................................................42 3.2.
1. Introduction 1 1. Introduction 1.1 Overview The AirVideo-100v2 is the most cost-effective and efficient way to do conference presentation. With AirLive Wireless Presenter Dongle, you may now upgrade your projector instantly with Wi-Fi capability by simply plug-connect the AirVideo-100 v2 to your projector.
1. Introduction z Plug & Show Perform your presentation wirelessly without swapping the cable when switching between presenters. There is an easy tool to make a Plug & Show USB Token on UI menu. Just link your PC/Laptop to WPS (through WLAN or Ethernet), plug the token into a USB port, and in seconds, your screen will be wireless projected to the connected projector! z AP & AP Client Mode AirVideo-100v2 works with AP mode and AP Client mode.
1. Introduction z Show 4 computers in single screen projection With this feature, up to four PC screens can be projected to one projector in the same time. Thus, you can easily do side-by-side comparison from four PC / PDAs to increase meeting productivity! z Macintosh(Mac) wireless projection AirVideo-100 v2 supports Mac client connected and projected wirelessly.
1. Introduction z Change Standby Screen You can use the application “Screen Image Background Maker” to change the Splash Screen. Design the image with message you would like to present, upload it through web control page, and you could have customized starting page. The AirVideo-100v2 will act as a Wireless Client to connect with the remote AP, let AirVideo-100v2 join an existing Access Point through Wi-Fi. This feature provides the flexibility of wireless network deployment in enterprise environment.
1. Introduction 1.2 Features z Wireless IEEE802.11b/g/n z Connect PC, smart phone and tablet to video projector wirelessly z Compatible with any VGA equipped projectors or LCD TV z Show 4 computers in single screen projection z Support WXGA+(1280 x 800) high quality projection resolution z Support smart phone presentation z 30FPS Real-Time Playback z Small and portable design z Support Wi-Fi AP client mode z Windows XP/Vista/7 and Mac OSX 10.
1. Introduction 1.4 Specification Table Standards Wireless channel Data Rate Protocol IP configuration Management Security Antenna Transmission Power Receive Sensitivity Supported PC/Laptop Resolution Supported Output Resolution Supported Windows Account Right Supported Operation System Power Interface LED Mechanical Environmental conditions Certificate . IEEE 802.11b/g/n 2.4GHz . IEEE 802.3(10BASE-T)/IEEE802.3u(100BASE-TX) . 11(US, Canada) . 13(Europe) . 14(Japan) Up to 150Mbps TCP/IP .
1. Introduction 1.5 Hardware Installation 1.5.1 Physical Detail 2. 3. 1.5.1 LED Indicator LED Status Power Description Green Power is on. 1.5.2 Button Definition Description Reset Step1: Remove the power adapter from AirVideo-100v2. Step2: Push the reset button. Step3: Plug the power adapter back into AirVideo-100v2. Step4: Till the power LED light turn to “Green”, and then release the reset button. Step5: The AirVideo-100v2 will load to factory default settings.
1. Introduction 1.5.3 Quick Start Step1: Please plug AirVideo-100v2 into projector VGA port, and open projector power to use.
1. Introduction Step2: Turn on AirVideo-100v2 z When Projector shows the default menu on the screen as below, it indicates the AirVideo-100v2 is ready now. (1) Make sure your WLAN PC is enabled already, and connect your PC with AirVideo-100v2. (2) Open your browser and enter the IP address to access the AirVideo-100v2 web home page. z The default IP address of AirVideo-100v2 is 192.168.1.1 or refers to the IP address shown on the left corner of projector screen.
1. Introduction (3) Download the client software. Please select the” Win7 / Windows Vista / XP” or” MAC” and execute the installation program. After installing the program, you will see the WPS shortcut on the PC screen.
1. Introduction (4) Making sure your personal firewall allows WPS software to pass through.
1. Introduction (6) Enter the Login Code and you can see the login code on the projector screen.
2. Getting Start 2 2. Getting Start 2.1 Windows Client Utility 2.1.1 Stating Program After you download WPS (Wireless Projector Server) Windows program via web page successfully, then follow below steps to start. Step1: Click WPS icon to execute the program. Step2: Program start to search for AirVideo-100v2 automatically. Step3: If AirVideo-100v2 founded then “Login Code” dialog box will be pop up on the PC screen.
2. Getting Start 2.1.2 Login (1) After “Login Code” dialog box shown, enter login code to start presentation. (2) You can see the login code shown on the projector screen. 2.1.3 Main User Interface Menu Area Status Indicator Speedy mode 2.1.
2. Getting Start Button Description Full Screen projection Project to Split #1 Project to Split #2 Project to Split #3 Project to Split #4 Stop projecting Pause projecting 2.1.
2. Getting Start 2.1.6 Show Login Code Click “Show Login Code”, it will display the login code on the right-upper of desktop and close it automatically after 10 seconds. You can also click on the area to close this window manually. 2.1.7 Open Admin Web Page Click to open function menu and select “Web Admin” management web page. web page detailed functions will be described on next chapter.
2. Getting Start 2.1.8 Wi-Fi Client Configuration Click “Wi-Fi AP Client Configuration” to set AP client mode to join others Access Point via wireless, besides, the others user client also can login AirVideo-100v2 for presentation and join to others Access Point network, 2.1.9 Searching Server Click “Search Server” to re-search the AirVideo-100v2 again.
2. Getting Start 2.1.10 Projection Source Click the “Projection Source”, you can select to project the main screen of desktop or the virtual extended screen. ※ Note: Virtual Extended Screen option, you need to install “VDD.exe” driver first which is stored in the USB token, you can find out the VDD program in supplied CD. 2.1.11 Auto Wi-Fi Connect Click “Auto Wi-Fi Connect” to enable the auto Wi-Fi discovery and connection function for quick wireless set up.
2. Getting Start 2.1.12 Auto Power Manager To make the highest projection performance, application will turn the PC’s windows power scheme from current settings to “highest performance”, however, you can click the “Auto Power Manage” to enable or disable this function and restore you power scheme immediately. 2.1.13 Hide UI Click the “Hide UI”, you can choose to hide or display the application control panel from projection screen.
2. Getting Start 2.1.14 Advanced Screen Capture Click the “Advanced Screen Capture”, you will be able to see tip windows and other layered windows (include the main UI) on the connected display. However, the mouse cursor may blink from time to time when you are projecting your PC screen! z Disable “Advanced Screen Capture”. A tip window is not shown in projector. z Enable “Advanced Screen Capture”. A tip window is shown in projector.
2. Getting Start 2.1.15 Make WPS Token Click “Make WPS Token” to make a USB WPS Token, you can insert a USB thumb drive and follows the wizard to make the Token.
2. Getting Start 2.1.16 Copy Application to desktop Click the “Copy Application to desktop”, it will copy the application to your desktop immediately even you don’t have the system privilege 2.1.17 Hot Key Click “Hot Key” to show Hot Key guide. You can use hot key to control the projection by keyboard.
2. Getting Start 2.1.18 About Click “About” - to show system information. It includes product model name, Client version, IP address and other information. 2.1.19 Exit Click “Exit” to exit this application. It will stop current playing status and close the application immediate.
2. Getting Start 2.2 Mac Client Utility 2.2.1 Launch Application This chapter guides how to use AirVideo-100v2 on MAC OS, the installation steps as below, Step1: Enable your Wi-Fi and connect to AirVideo-100v2 device. Step2: Execute WPS client software for Mac. Step3: Launch WPS software and enter the login code.
2. Getting Start Step4: Start Projection. 2.2.2 Main User Interface Control Area for Screen Projection Feature Status Indicator 2.2.3 Screen Projection Click the “Play” button for full or split screen, you can project the main screen on to the display immediately, click the “Pause” button, you can freeze you projection screen, and click the “Stop” button to stop projecting your screen.
2. Getting Start Button Description Full Screen projection Project to Split #1 Project to Split #2 Project to Split #3 Project to Split #4 Stop projecting Pause projecting Refresh Screen 2.3 Web Management 2.3.1 Home Page There are two way to manage AirVideo-100v2 via WPS utility and via Web Management. Here, we will introduce the Web Management. Step1: Make sure your PC connect to AirVideo-100v2 successfully. Step2: Open your browser, it will enter AirVideo-100v2’s home page automatically.
2. Getting Start 2.3.2 Download Software On the left-side of Web Management, you can select “Download software” function if you haven’t yet install the WPS utility into your device before. Step1: Select the “Win 7 / Windows Vista / XP” or “Mac Utility” and execute the installation program. Step2: Follow Installation Wizard instructions to proceed till the installation process complete. Step3: If pop up “Windows Security Alert” because Windows firewall block this program.
2. Getting Start 2.3.3 Login Web Admin 1. Click [Admin] and then enter password to login web page. 2. The password default value is “airlive”.
2. Getting Start 2.3.4 System Status This page is shown the System Status include Model Name, Version, Network Status and Connection Status. Click [System Status], shows current system status. Model Name: Product model name Versions: 1. Firmware version no.: Product firmware version number. Network Status: 1. IP address：IP address of AirVideo-100v2 device. 2. Subnet Mask：subnet mask 3. Default Gateway：default gateway 4. Wireless MAC address：wireless MAC address 5.
2. Getting Start 2.3.5 Network Setup There are many kinds of operating configurations as below, IP Setup, respectively DHCP Server and Wireless Setup and AP Client. < Auto-Configuration Network Setup> The default setting of the AirVideo-100v2 box is DHCP client. • When the AirVideo-100v2 is connected to a LAN that already has a DHCP server present, the AirVideo-100v2 takes an IP address assigned to it by the server.
2. Getting Start < IP Setup> z You can select “obtain IP address automatically” or “Use the following IP address” z IP Address: The default value is 192.168.100.10. z Subnet Mask: The default value is 255.255.255.0 z Default Gateway: The default value is 192.168.100.10 z DNS Server: The default value is 192.168.100.10 z You can select “Auto(Enable/Disable DHCP Server” or “Disable”) z Start IP: The start IP address of DHCP Server.
2. Getting Start < Gatekeeper> Gatekeeper is designed for ensuring the enterprise network security within AirVideo-100v2 z All Block can block Guest Users(through wireless) to access all office network(LAN), z All Allow can pass Guest Users(through wireless) to access all office network z Internet Only can block Guest Users (through wireless) from office network (LAN) but still reserve internet connection capability. : press button to select this mode. : press button to abort action.
2. Getting Start 2.3.7 Projection Setup This option can change the resolution and login code on your projector. Click [Projection Setup] button z : VGA: XGA (1024*768), WXGA (1280x800), WXGA (1280*768) and SVGA (800*600). The default value is XGA. HDMI: 720p (1280*720) z : You can select “Disable”, “Random”, or “Use the following code” to set a specified 4-characters Number.
2. Getting Start 2.3.8 Change Passwords You can change the Web Management Password here. We strongly recommend you to change the password for security reason. Click on “Apply” to store your settings. Click [Change Password] button, to change password value. The length of password is up to 8 characters. z : enter new password you want to change for each category. z : double confirm new password. z : Confirmation and Save modifications.
2. Getting Start 2.3.9 Reset to Default You can also reset this device to factory default settings by clicking the Reset to default function item. Click [Reset to Default] button to restore factory default settings. : Confirmation and action. 2.3.10 Firmware Upgrade Click [Firmware Upgrade] button to upgrade firmware. 1. Firstly, you have to get latest firmware image file from your vendor. 2. Click to specify file name you want to upgrade. 3. Click to start. 4.
2. Getting Start Warning: Please DON’T turn the AirVideo-100v2 power off while firmware upgrade in progress, otherwise it will cause your AirVideo-100v2 malfunction; you will have to return device for RMA. .
2. Getting Start 2.3.11 Reboot System To reboot the device- Click [Reboot System] button, to restart system z : reboot system automatically. 2.3.
2. Getting Start 2.3.13 Screen Image Background Maker This chapter guides you how to change the Background Image. The installation steps as below, Step1: Run the “Screen Image Background Maker” and follows the wizard to convert the image file.
2. Getting Start Step2: Press “Open” to select a file to convert this image for background use. Step3: Press “Saver” to save this file. (*.
2. Getting Start Step4: Please connect to AirVideo-100v2’s webpage, and then connect to OSD setup page. Step5: Press “Browser” to choose the *.ib file.
2. Getting Start Step6: Press “image file upload” to upload your background image, then it will show the message as below. ※ Note: You may find “Screen Image Background Maker” in the USB Token.
3. Smart Phone Application 3. Smart phone 3. Application 3 3.1 Introduce The AirVideo-100 v2 supports to presentation on different Smartphone platforms via MobiShow. In this chapter will introduce how to play the file, photo or even show your screen profile from your mobile to big screen wirelessly. MobiShow has included Screen Projection, PtG(Presentation-to-Go) and Photo Viewer. The below table shown the support list on the smart phone.
3. Smart Phone Application The following control panel is displayed on your Desktop when it is launched. z Click the “ Convert” button to select a PowerPoint PPT file and start conversion. PtG Converter will open the PowerPoint file and convert it to PtG format. You can see the conversion process on your Desktop. z Click the “ z Click “ z Or click “ Preview” button to expand or collapse the preview pane. Play” to playback selected PtG file. Open” to select a PtG file. 3.2.
3. Smart Phone Application Step 4: Select a MobiShow wireless network (SSID with prefix MobiShow) to connect to. Step 5: MobiShow client will connect to that access point and search for MobiShow devices automatically. When a MobiShow device is found, it will automatically login and the following main menu is shown on your phone. z If more than one MobiShow devices are found, the following list will be displayed for you to select the one to use.
3. Smart Phone Application z Select which feature to use. To project the screen of your phone, click on the “Screen” icon. To do a PC-less presentation with Presentation-to-Go (PtG), select the “PtG” icon. 3.2.2.1 Screen Projection MobiShow will project anything displayed on your screen. You may launch another application (such PowerPoint Viewer) or open any file (such as Word document or JPG image) and it will be projected to the projector.
3. Smart Phone Application z z z z z Click the “Stop” icon to stop projection. Click the “Pause” icon to pause projection. Click “Pause” again to resume projection. Click the “Zoom” icon to zoom the projected screen to extend the longest side of your screen to fill the screen. Click the “Play” icon to start projection again if it is stopped. Click the “OK” button or “Back” to return to main menu. 3.2.2.
3. Smart Phone Application 3.2.2.3 Photo Viewer You can use MobiShow to project photos stored on your phone to big screen. The photos will be prepared for playback on big screens rather than for the tiny screens of your phone. To open a single photo, select one photo and click the OK button. The photo will be displayed on the display connected to MobiShow device. z z Click “Prev” or “Next” to go to the previous or next photo in the same folder.
3. Smart Phone Application 3.2.3 MobiShow via iOS 3.2.3.1 Start the MobiShow This section guides you how to use MobiShow feature to show your data via the iOS. The installation steps as below, z Find on your iPhone/iPod touch, and then touch it to launch app. After a little time of searching, you will see a list of available receivers. z Touch z will be changed into See image below. z AirLive AirVideo-100v2 User’s Manual to connect and the successfully connected receiver .
3. Smart Phone Application 3.2.3.2 Start PtG Player z Touch on the tab bar to view PtG file list on document folder. Currently we support files with two file extensions, which are '.ptg' and '.ptg2'. See image below. z Touch to play PtG file on connected receiver. playing PtG file, screen will changed into controller. See image below.
3. Smart Phone Application z Touch to go to previous page, and touch z Touch to go to previous item, and touch z Touch to play next item. z Touch to stop playing PtG file. for next page. for next item. 3.2.3.3 Start Media Player z Touch on the tab bar to view media file on document folder. support files with extension '.mpeg', '.avi', '.mp3'. See image below.
3. Smart Phone Application z Touch to play media file on connected receiver. While playing media file, screen will changed into controller. See image below. z Touch to play backward, and disabled in this version. z Touch to decrease volume, and z Touch to pause, and z Touch to stop playing media file. z Touch to mute voice. for forward. These two functions are to increase volume. to play.
3. Smart Phone Application 3.2.3.4 Photo Slideshow z Touch on the tab bar to view media file on document folder. support files with extension '.mpeg', '.avi', '.mp3'. See image below. z Touch to play photo file on connected receiver. While playing photo file, screen will changed into controller. See image below. z Touch to play previous photo, and for next one. z Touch to pause playing photo, and to stop.
3. Smart Phone Application 3.2.3.5 How to upload file with iTunes It is necessary to use iTunes to upload the file into iPad or iPhone. z Click on your Mac or PC to start iTunes. z Be sure your iPhone is connected to your Mac or PC, of course. z Click on the iTunes, and then click . A few seconds later, you'll see what apps you have already installed are right on your iPhone. z Click , and you can see everything you uploaded associated with MobiShow Lite.
4. Appendix 4. Appendix 4 Troubleshooting Q: Why can’t I connect to AirVideo-100v2’s Web Management even the wireless show I had connected to the AirViedo-100’s SSID. A: Do a Ping test to make sure that the AirVideo-100v2 is responding. Go to Start > Run. 1. Type cmd. 2. Press OK. 3. Type ipconfig to get the IP of default gateway. 4. Type “ping 192.168.1.1”. Assure that you ping the correct IP Address assigned to the AirVideo-100v2. It will show four replies if you ping correctly.
4. Appendix 3. Click Device Manager. 4. Double-click on “Network Adapters”. 5. Right-click on Wireless Card bus Adapter or your specific network adapter. 6. Select Properties to ensure that all drivers are installed properly. 7. Look under Device Status to see if the device is working properly. 8. Click “OK”. Q: Something wrong with the wireless connection? A: Can’t setup a wireless connection? I. Ensure that the SSID and the encryption settings are exactly the same to the Clients. II.
4. Appendix correct Access Point. i. Right-click on the Local Area Connection icon in the taskbar. ii. Select View Available Wireless Networks in Wireless Configure. Ensure you have selected the correct available network. iii. Reset the AirVideo-100v2 to default setting Why does my wireless connection keep dropping? I. Try changing the channel on the AirVideo-100v2, and your Access Point and Wireless adapter to a different channel to avoid interference. II.
4. Appendix Please noticed, the below items need to be same on both sides. • SSID • Wireless Encryption(such as WEP, WPN and WPA2-PSK) • Wireless mode(IEEE 802.11b/g/n) Then, the Local users can connect AirVideo-100v2 or Internet via Wired, via Wireless. Q: What to do if I forgot my encryption key? A: 1. Go back to advanced setting to set up your Encryption key again. 2. Reset the AirVideo-100v2 to default setting Q: How to reset to default? A: Step1: Remove the power adapter from AirVideo-100v2.
4. Appendix Q: Does AirVideo-100v2 support Power over VGA, which printer can be supported? A: Yes, the AirVideo-100v2 supports Power over VGA and it can compatible with the following projectors: . Optoma EX542 . Optoma EX612 . Optoma EX615 . Optoma EX762 .
