SNMP-GSH2416 8+16 Pure Gigabit SNMP Managed Switch
Table of Contents CAUTION -------------------------------------------------------------------------------------- IV ELECTRONIC EMISSION NOTICES --------------------------------------------------------- IV CHAPTER 1. INTRODUCTION--------------------------------------------------------- 2 1-1. OVERVIEW OF SNMP-GSH2416 SNMP MANAGED GIGABIT SWITCH ------- 2 1-2. CHECKLIST ----------------------------------------------------------------------------- 4 1-3.
-2-3. Simple Counter----------------------------------------------------------------54 3-2-4. Detail Counter -----------------------------------------------------------------56 3-3. MIRROR --------------------------------------------------------------------------------59 3-4. BANDWIDTH MANAGEMENT ---------------------------------------------------------60 3-5. QOS(QUALITY OF SERVICE) CONFIGURATION -----------------------------------62 3-6.
Caution Circuit devices are sensitive to static electricity, which can damage their delicate electronics. Dry weather conditions or walking across a carpeted floor may cause you to acquire a static electrical charge. To protect your device, always: • Touch the metal chassis of your computer to ground the static electrical charge before you pick up the circuit device. • Pick up the device by holding it on the left and right edges only.
About this user’s manual In this user’s manual, it will not only tell you how to install and connect your network system but configure and monitor the SNMP-GSH2416 SNMP Managed Gigabit Switch through the built-in CLI and web by RS-232 serial interface and Ethernet ports step-by-step. Many explanation in detail of hardware and software functions are shown as well as the examples of the operation for web-based interface and command-line interface (CLI).
1. Introduction 1-1. Overview of SNMP-GSH2416 SNMP Managed Gigabit Switch 24-port Gigabit L2 Managed Switch, is a standard switch that meets all IEEE 802.3/u/x/z Gigabit, Fast Ethernet specifications. The switch included 8-Port 10/100/1000Mbps TP and 16-Port Gigabit SFP Fiber management Ethernet switch. The switch can be managed through RS-232 serial port via directly connection, or through Ethernet port using CLI or Web-based management unit, associated with SNMP agent.
• Key Features in the Device QoS: Support Quality of Service by the IEEE 802.1P standard. There are two priority queue and packet transmission schedule. Spanning Tree: Support IEEE 802.1D, IEEE 802.1w (RSTP: Rapid Spanning Tree Protocol) standards. VLAN: Support Port-based VLAN and IEEE802.1Q Tag VLAN. Support 256 active VLANs and VLAN ID 1~4094. Port Trunking: Support static port trunking and port trunking with IEEE 802.3ad LACP. Bandwidth Control: Support ingress and egress per port bandwidth control.
1-2. Checklist Before you start installing the switch, verify that the package contains the following: ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ A set of SNMP-GSH2416 SNMP Managed Gigabit Switch Modules (optional) Mounting Accessory (for 19” Rack Shelf) This User's Manual in CD-ROM AC Power Cord RS-232 Cable Please notify your sales representative immediately if any of the aforementioned items is missing or damaged. 1-3.
• Supports 802.
1-4. View of SNMP-GSH2416 SNMP Managed Gigabit Switch Fig. 1-1 Full View of 8-Port TP + 16-Port SFP L2 Managed Gigabit Switch 1-4-1. User Interfaces on the Front Panel (Button, LEDs and Plugs) There are 8 TP Gigabit Ethernet ports and 16 SFP fiber ports for optional removable modules on the front panel of the switch. LED display area, locating on the left side of the panel, contains a Power LED, which indicates the power status and 24 ports working status of the switch.
• LED Indicators LED POWER CPU LED Color System LED Green Green Function Lit when +5V DC power is on and good Blinks when CPU is activity 10/100/1000Ethernet TP Port 1 to 8 LED Lit when connection with remote device is good LINK/ACT Green Blinks when any traffic is present Off when cable connection is not good Lit green when 1000Mbps speed is active Green/ SPEED Lit ember when 100Mbps speed is active Ember Off when 10Mbps speed is active 1000SX/LX Gigabit Fiber Port 9 to 24 LED Lit when connection with
1-5. View of the Optional Modules In the switch,1000Mbps SFP Fiber transceiver is used for high-speed connection expansion; the following are optional SFP types provided for the switch: ⎯ 1000Mbps LC, MM, SFP Fiber transceiver (SFP.0LC.202) ⎯ 1000Mbps LC, SM 10km, SFP Fiber transceiver (SFP.0LC.212.10) ⎯ 1000Mbps LC, SM 30km, SFP Fiber transceiver (SFP.0LC.212.30) ⎯ 1000Mbps LC, SM 50km, SFP Fiber transceiver (SFP.0LC.212.50) ⎯ 1000Mbps BiDi LC, type 1, SM 20km, SFP Fiber WDM transceiver (SFP.0BL.
2. Installation 2-1. Starting SNMP-GSH2416 SNMP Managed Gigabit Switch Up This section will give users a quick start for: - Hardware and Cable Installation - Management Station Installation - Software booting and configuration 2-1-1.
• TP Port and Cable Installation ⇒ In the switch, TP port supports MDI/MDI-X auto-crossover, so both types of cable, straight-through (Cable pin-outs for RJ-45 jack 1, 2, 3, 6 to 1, 2, 3, 6 in 10/100M TP; 1, 2, 3, 4, 5, 6, 7, 8 to 1, 2, 3, 4, 5, 6, 7, 8 in Gigabit TP) and crossed-over (Cable pin-outs for RJ-45 jack 1, 2, 3, 6 to 3, 6, 1, 2) can be used. It means you do not have to tell from them, just plug it. ⇒ Use Cat.
2-1-2. Installing Chassis to a 19-Inch Wiring Closet Rail Fig. 2-2 Caution: Allow a proper spacing and proper air ventilation for the cooling fan at both sides of the chassis. ⇒ Wear a grounding device for electrostatic discharge. ⇒ Screw the mounting accessory to the front side of the switch (See Fig. 2-2). ⇒ Place the Chassis into the 19-inch wiring closet rail and locate it at the proper position. Then, fix the Chassis by screwing it. 2-1-3.
2-1-3-1. Cabling Requirements for TP Ports ⇒ For Fast Ethernet TP network connection ⎯ The grade of the cable must be Cat. 5 or Cat. 5e with a maximum length of 100 meters. ⇒ Gigabit Ethernet TP network connection ⎯ The grade of the cable must be Cat. 5 or Cat. 5e with a maximum length of 100 meters. Cat. 5e is recommended. 2-1-3-2. Cabling Requirements for 1000SX/LX SFP Module It is more complex and comprehensive contrast to TP cabling in the fiber media.
2-1-3-3. Switch Cascading in Topology • Takes the Delay Time into Account Theoretically, the switch partitions the collision domain for each port in switch cascading that you may up-link the switches unlimitedly. In practice, the network extension (cascading levels & overall diameter) must follow the constraint of the IEEE 802.3/802.3u/802.3z and other 802.1 series protocol specifications, in which the limitations are the timing requirement from physical signals defined by 802.
Case1: All switch ports are in the same local area network. Every port can access each other (See Fig. 2-3). Fig. 2-3 No VLAN Configuration Diagram If VLAN is enabled and configured, each node in the network that can communicate each other directly is bounded in the same VLAN area. Here VLAN area is defined by what VLAN you are using. The switch supports both port-based VLAN and tag-based VLAN. They are different in practical deployment, especially in physical location.
Case 2b: Port-based VLAN (See Fig.2-5). Fig. 2-5 Port-based VLAN Diagram 1. VLAN1 members could not access VLAN2, VLAN3 and VLAN4 members. 2. VLAN2 members could not access VLAN1 and VLAN3 members, but they could access VLAN4 members. 3. VLAN3 members could not access VLAN1, VLAN2 and VLAN4. 4. VLAN4 members could not access VLAN1 and VLAN3 members, but they could access VLAN2 members. Case3a: The same VLAN members can be at different switches with the same VID (See Fig. 2-6).
2-1-4. Configuring the Management Agent of SNMP-GSH2416 SNMP Managed Gigabit Switch We offer you three ways to startup the switch management function. They are RS-232 console, CLI, and Web. Users can use any one of them to monitor and configure the switch. You can touch them through the following procedures.
2-1-4-1. Configuring the Management Agent of SNMP-GSH2416 SNMP Managed Gigabit Switch through the Serial RS-232 Port To perform the configuration through RS-232 console port, the switch’s serial port must be directly connected to a DCE device, for example, a PC, through RS-232 cable with DB-9 connector. Next, run a terminal emulator with the default setting of the switch’s serial port. With this, you can communicate with the switch. In the switch, RS-232 interface only supports baud rate 57.
• Set IP Address, Subnet Mask and Default Gateway IP Address Please refer to Fig. 2-7 CLI Management for details about the ex-factory setting. They are default setting of IP address. You can first either configure your PC IP address or change IP address of the switch, next to change the IP address of default gateway and subnet mask. For example, your network address is 10.1.1.0, and subnet mask is 255.255.255.0. You can change the switch’s default IP address 192.168.1.1 to 10.1.1.
2-1-4-2. Configuring the Management Agent of SNMP-GSH2416 SNMP Managed Gigabit Switch through the Ethernet Port There are three ways to configure and monitor the switch through the switch’s Ethernet port. They are CLI, Web browser and SNMP manager. The user interface for the last one is NMS dependent and does not cover here. We just introduce the first two types of management interface. 8-Port TP + 16-Port SFP L2 Managed Gigabit Switch Default IP Setting: IP = 192.168.1.1 Subnet Mask = 255.255.255.
Fig. 2-10 the Login Screen for Web 2-1-5. IP Address Assignment For IP address configuration, there are three parameters needed to be filled in. They are IP address, Subnet Mask, Default Gateway and DNS. IP address: The address of the network device in the network is used for internetworking communication. Its address structure looks is shown in the Fig. 2-11. It is “classful” because it is split into predefined address classes or categories.
With the classful addressing, it divides IP address into three classes, class A, class B and class C. The rest of IP addresses are for multicast and broadcast. The bit length of the network prefix is the same as that of the subnet mask and is denoted as IP address/X, for example, 192.168.1.0/24. Each class has its address range described below. Class A: Address is less than 126.255.255.255. There are a total of 126 networks can be defined because the address 0.0.0.0 is reserved for default route and 127.0.
Class D and E: Class D is a class with first 4 MSB (Most significance bit) set to 1-1-1-0 and is used for IP Multicast. See also RFC 1112. Class E is a class with first 4 MSB set to 1-1-1-1 and is used for IP broadcast. According to IANA (Internet Assigned Numbers Authority), there are three specific IP address blocks reserved and able to be used for extending internal network. We call it Private IP address and list below: Class A Class B Class C 10.0.0.0 --- 10.255.255.255 172.16.0.0 --- 172.31.255.
In this diagram, you can see the subnet mask with 25-bit long, 255.255.255.128, contains 126 members in the sub-netted network. Another is that the length of network prefix equals the number of the bit with 1s in that subnet mask. With this, you can easily count the number of IP addresses matched. The following table shows the result. Prefix Length No. of IP matched No.
For different network applications, the subnet mask may look like 255.255.255.240. This means it is a small network accommodating a maximum of 15 nodes in the network. Default gateway: For the routed packet, if the destination is not in the routing table, all the traffic is put into the device with the designated IP address, known as default router. Basically, it is a routing policy. The gateway setting is used for Trap Events Host only in the switch.
2-2. Typical Applications The SNMP-GSH2416 SNMP Managed Gigabit Switch L2 Managed Switch implements 8 Gigabit Ethernet TP ports with auto MDIX and 16 slots for the removable module supporting comprehensive fiber types of connection, including LC and BiDi-LC SFP modules. For more details on the specification of the switch, please refer to Appendix A. ⎯ The switch is suitable for the following application. Central Site/Remote site application is used in carrier or ISP (See Fig. 2-13) Central Site Fig.
3. Operation of Web-based Management This chapter instructs you how to configure and manage the switch through the web user interface it supports, to access and manage the 8-Port 10/100/1000Mbps TP and 16-Port Gigabit SFP Fiber management Ethernet switch.
In the switch, it supports a simple user management function allowing only one administrator to configure the system at the same time. If there are two or more users using administrator’s identity, the switch will allow the only one who logins first to configure the system. The rest of users, even with administrator’s identity, can only monitor the system. For those who have no administrator’s identity, can only monitor the system.
3-1. Web Management Home Overview After you login, the switch shows you the system information as Fig. 3-2. This page is default and tells you the basic information of the system, including “Model Name”, “System Description”, “Location”, “Contact”, “Device Name”, “System Up Time”, “Current Time”, “BIOS Version”, “Firmware Version”, “Hardware-Mechanical Version”, “Serial Number”, “Host IP Address”, “Host Mac Address”, “Device Port”, “RAM Size” and “Flash Size”.
• The Information of Page Layout ⎯ On the top side, it shows the front panel of the switch. In the front panel, the linked ports will display green; as to the ports, which are link off, they will be dark. For the optional modules, the slot will show only a cover plate if no module exists and will show a module if a module is present. The image of module depends on the one you inserted. The same, if disconnected, the port will show just dark, if linked, green.
tree for web user interface. Root System Port Mirror Bandwidth QoS SNMP IGMP Snooping Max. Packet Length DHCP Boot VLAN MAC Table GVRP STP Trunk 802.
3-1-1. System Information Function name: System Information Function description: Show the basic system information. Parameter description: Model name: The model name of this device. System description: As it is, this tells what this device is. Here, it is “L2 Managed Switch”. Location: Basically, it is the location where this switch is put. User-defined. Contact: For easily managing and maintaining device, you may write down the contact person and phone here for getting help soon.
Host IP address: The IP address of the switch. Host MAC address: It is the Ethernet MAC address of the management agent in this switch. Device Port: Show all types and numbers of the port in the switch. RAM size: The size of the DRAM in this switch. Flash size: The size of the flash memory in this switch.
3-1-2. IP Configuration IP configuration is one of the most important configurations in the switch. Without the proper setting, network manager will not be able to manage or view the device. The switch supports both manual IP address setting and automatic IP address setting via DHCP server. When IP address is changed, you must reboot the switch to have the setting taken effect and use the new IP to browse for web management and CLI management. Fig.
IP address: Users can configure the IP settings and fill in new values if users set the DHCP function “Disable”. Then, click button to update. When DHCP is disabled, Default: 192.168.1.1 If DHCP is enabled, this field is filled by DHCP server and will not allow user manually set it any more.
DNS: It is Domain Name Server used to serve the translation between IP address and name address. The switch supports DNS client function to re-route the mnemonic name address to DNS server to get its associated IP address for accessing Internet. User can specify a DNS IP address for the switch. With this, the switch can translate a mnemonic name address into an IP address. There are two ways to specify the IP address of DNS.
3-1-3. Time Configuration The switch provides manual and automatic ways to set the system time via NTP. Manual setting is simple and you just input “Year”, “Month”, “Day”, “Hour”, “Minute” and “Second” within the valid value range indicated in each item. If you input an invalid value, for example, 61 in minute, the switch will clamp the figure to 59. NTP is a well-known protocol used to synchronize the clock of the switch system time over a network.
NTP: NTP is Network Time Protocol and is used to sync the network time based Greenwich Mean Time (GMT). If use the NTP mode and select a built-in NTP time server or manually specify an user-defined NTP server as well as Time Zone, the switch will sync the time in a short after pressing button. Though it synchronizes the time automatically, NTP does not update the time periodically without user’s processing. Time Zone is an offset time off GMT.
Day Light Saving End : This is used to set when to stop performing the daylight saving time. Mth: Range is 1 ~ 12. Default: 1 Day: Range is 1 ~ 31. Default: 1 Hour: Range is 0 ~ 23. Default: 0 Fig.
3-1-4. Account Configuration In this function, only administrator can create, modify or delete the username and password. Administrator can modify other guest identities’ password without confirming the password but it is necessary to modify the administrator-equivalent identity. Guest-equivalent identity can modify his password only. Please note that you must confirm administrator/guest identity in the field of Authorization in advance before configuring the username and password.
3-1-5. Management Policy Through the management security configuration, the manager can do the strict setup to control the switch and limit the user to access this switch. The following rules are offered for the manager to manage the switch: Rule 1) : When no lists exists, then it will accept all connections.
Function name: Management Security Configuration Function description: The switch offers Management Security Configuration function. With this function, the manager can easily control the mode that the user connects to the switch. According to the mode, users can be classified into two types: Those who are able to connect to the switch (Accept) and those who are unable to connect to the switch (Deny).
IP Range: The switch supports two kinds of options for managed valid IP Range, including “Any” and “Custom”. Default is “Any”. In case that” Custom” had been chosen, you can assigned effective IP range. The valid range is 0.0.0.0~255.255.255.255. Incoming Port: The switch supports two kinds of options for managed valid Port Range, including “Any” and “Custom”. Default is “Any”.
3-1-6. Virtual Stack Function name: Virtual Stack Function description: Virtual Stack Management(VSM) is the group management function. Through the proper configuration of this function, switches in the same LAN will be grouped automatically. And among these switch, one switch will be a master machine, and the others in this group will become the slave devices. VSM offers a simple centralized management function.
Fig. 3-8 Parameter description: State: It is used for the activation or de-activation of VSM. Default is Enable. Role: The role that the switch would like to play in virtual stack. Two types of roles, including master and slave are offered for option. Default is Master. Group ID: It is the group identifier (GID) which signs for VSM. Valid letters are A-Z, a-z, 0-9, “ - “ and “_” characters. The maximal length is 15 characters.
Fig.
3-2. Port Configuration Four functions, including Port Status, Port Configuration, Simple Counter and Detail Counter are contained in this function folder for port monitor and management. Each of them will be described in detail orderly in the following sections. Port Configuration Status Configuration Simple Counter Detail Counter 3-2-1.
Fig.
Function name: Port Status Function Description: Report the latest updated status of all ports in this switch. When any one of the ports in the switch changes its parameter displayed in the page, it will be automatically refreshed the port current status about every 5 seconds. Parameter Description: Port No: Display the port number. The number is 1 – 24. Media: Show the media type adopted in all ports.
Speed / Duplex Mode: Display the speed and duplex of all port. There are three speeds 10Mbps, 100Mbps and 1000Mbps supported for TP media, and the duplex supported is half duplex and full duplex. If the media is 1Gbps fiber, it is 1000Mbps supported only. The status of speed/duplex mode is determined by 1) the negotiation of both local port and link partner in “Auto Speed” mode or 2) user setting in “Force” mode. The local port has to be preset its capability.
Fig. 3-11 Parameter description of Port 9~24: Connector Type: Display the connector type, for instance, UTP, SC, ST, LC and so on. Fiber Type: Display the fiber mode, for instance, Multi-Mode, Single-Mode. Tx Central Wavelength: Display the fiber optical transmitting central wavelength, for instance, 850nm, 1310nm, 1550nm and so on. Baud Rate: Display the maximum baud rate of the fiber module supported, for instance, 10M, 100M, 1G and so on.
Vendor SN (Serial Number): Show the serial number assigned by the manufacturer. Date Code: Show the date this SFP module was made. Temperature: Show the current temperature of SFP module. Vcc: Show the working DC voltage of SFP module. Mon1(Bias) mA: Show the Bias current of SFP module. Mon2(TX PWR): Show the transmit power of SFP module. Mon3(RX PWR): Show the receiver power of SFP module.
3-2-2. Port Configuration Port Configuration is applied to change the setting of each port. In this configuration function, you can set/reset the following functions. All of them are described in detail below. Fig. 3-12 Function name: Port Configuration Function description: It is used to set each port’s operation mode. The switch supports 3 parameters for each port. They are state, mode and flow control. Parameter description: State: Set the communication capability of the port is Enabled or Disabled.
Mode: Set the speed and duplex of the port. In speed, if the media is 1Gbps fiber, it is always 1000Mbps and the duplex is full only. If the media is TP, the Speed/Duplex is comprised of the combination of speed mode, 10/100/1000Mbps, and duplex mode, full duplex and half duplex. The following table summarized the function the media supports. Media type 1000M TP 1000M Fiber NWay ON/OFF ON/OFF Speed 10/100/1000M 1000M Duplex Full for all, Half for 10/100 Full In Auto-negotiation mode, no default value.
3-2-3. Simple Counter The function of Simple Counter collects any information and provides the counting about the traffic of the port, no matter the packet is good or bad. In the Fig. 3-13, the window can show all ports’ counter information at the same time. Each data field has 20-digit long. If the counting is overflow, the counter will be reset and restart counting. The data is updated every time interval defined by the user. The valid range is 3 to 10 seconds.
Rx Packet: The counting number of the packet received. Tx Collision: Number of collisions transmitting frames experienced. Rx Error Packet: Number of bad packets received.
3-2-4. Detail Counter The function of Detail Counter collects any information and provides the counting about the traffic of the port, no matter the packet is good or bad. In the Fig. 3-14, the window can show only one port counter information at the same time. To see another port’s counter, you have to pull down the list of Select, then you will see the figures displayed about the port you had chosen. Each data field has 20-digit long.
Rx Low Priority Packets: Number of Rx packets classified as low priority. Rx Broadcast: Show the counting number of the received broadcast packet. Rx Multicast: Show the counting number of the received multicast packet. Tx Packets: The counting number of the packet transmitted. TX Octets: Total transmitted bytes. Tx High Priority Packets: Number of Tx packets classified as high priority. Tx Low Priority Packets: Number of Tx packets classified as low priority.
Tx 65-127 Bytes: Number of 65 ~ 126-byte frames in good and bad packets transmitted. Tx 128-255 Bytes: Number of 127 ~ 255-byte frames in good and bad packets transmitted. Tx 256-511 Bytes: Number of 256 ~ 511-byte frames in good and bad packets transmitted. Tx 512-1023 Bytes: Number of 512 ~ 1023-byte frames in good and bad packets transmitted. Tx 1024-Bytes: Number of 1024-max_length-byte frames in good and bad packets transmitted.
3-3. Mirror Function name: Mirror Configuration Function description: Mirror Configuration is to monitor the traffic of the network. For example, we assume that Port A and Port B are Monitoring Port and Monitored Port respectively, thus, the traffic received by Port B will be copied to Port A for monitoring. Note: When configuring the mirror function, you should avoid setting a port to be a sniffer port and aggregated port at the same time. It will cause something wrong.
3-4. Bandwidth Management Function name: Bandwidth Management Function description: Bandwidth Management function is used to set up the limit of Ingress and Egress bandwidth for each port. Note: Each port of the switch owns 16KB packet buffer. The packet buffer size will be reduced when the bandwidth rate limitation is enabled, which may cause that jumbo frame cannot be forwarded. Please avoid enabling jumbo frame and bandwidth rating functions at the same time. Fig.
Broadcast & Multicasat for Ingress Rate Limiting (Policing): Set up the limit of Ingress bandwidth for the port you choose. Incoming traffic will be discarded if the rate exceeds the value you set up in Data Rate field. The format of the packet limits to broadcast and multicast. Valid range is 0~1000. All Traffic for Egress Rate Limiting(Shaping): Set up the limit of Egress bandwidth for the port you choose. Packet transmission will be delayed if the rate exceeds the value you set up in Data Rate field.
3-5. QoS(Quality of Service) Configuration The switch offers powerful 5 kinds of QoS functions. There are Per Port Priority that you can assign each port to different precedence, VLAN Tag priority that can make precedence of 8 priorities, IP TOS Classification, IP TCP/UDP Port Classification and IP DiffServe Classification. In Quality of Service (QoS) Configuration, there is one option named” Default Class”.
Function name: Per Port Priority Function description: We can assign QoS Priority, including High and Low for each port. For example, if we transmit IP packets from Port 2 and Port 3 at the speed of 1Gbps to Port 1, and set the Class of Port 2 as High and Port 3 as Low, then the packets of Port 3 will be dropped when the congestion happens because Port 2 owns higher precedence of transmitting packets.
Function name: VLAN Tag Priority Function description: In vlan tag, there are 3 bits belonging to priority. According to these 3 bits, we could arrange 8 traffics –0 0 0, 0 0 1, 0 1 0, 0 1 1, 1 0 0, 1 0 1, 1 1 0, 1 1 1. We can set High priority or Low priority for each traffic class. For instance, if we let VLAN-tagged priority 0 0 0 be high priority and VLAN-tagged priority 0 0 1 be Low Priority, and then make port 1, 2, 3 be in the vlan 2.
Bit 0, Bit 1, Bit 2: According to the arrangement of VLAN-tagged priority, it can form 8 kinds of traffics, including 0 0 0, 0 0 1, 0 1 0, 0 1 1, 1 0 0, 1 0 1, 1 1 0 and 1 1 1. Class: 8 kinds of traffic as mentioned above, user can set up High Priority or Low Priority for each port respectively.
Function name: IP ToS Classification Function description: Another QoS function is the application of Layer 3 on network framework. We focus on TOS field of IP header. There are three bits in TOS field. We means bit 5~7 of TOS field that we will use. According to these 3 bits, we could arrange 8 traffics –0 0 0, 0 0 1, 0 1 0, 0 1 1, 1 0 0, 1 0 1, 1 1 0, 1 1 1. As long as we change bit 5~7 of TOS field of IP header, we will create the 8 traffic packets we meant before.
Bit 0, Bit 1, Bit 2: According to the arrangement of Bit 5 ~ Bit 7 in TOS Field of IP Header, it can form 8 kinds of traffics, including 0 0 0, 0 0 1, 0 1 0, 0 1 1, 1 0 0, 1 0 1, 1 1 0 and 1 1 1. Class: 8 kinds of traffic as mentioned above, user can set up High Priority or Low Priority for each port respectively.
Function name: IP TCP/UDP Port Classification Function description: In L4 QoS Configuration, you can enter one of these special network transmission events, for example we use” Down prioritize web browsing, e-mail, FTP and news “L4 QoS Configuration and click button, and then click >> button.
Prioritize Streaming Audio/Video: Belong to the QoS in L4. Just tick the option button and press button to have this function taken affect. Then, click >> button set up Special TCP/UDP port for QoS. Prioritize Databases (Oracle, IBM DB2, SQL, Microsoft): Belong to the QoS in L4. Just tick the option button and press button to have this function taken affect. Then, click >> button to set up Special TCP/UDP port for QoS.
Fig. 3-21 Advanced Mode Fig. 3-22 Simple Mode Simple Mode: Press button is to return to the screen that all L4 port number will disappear (See Fig. 3-22).
Function name: IP Diffserv Classification Function description: In the late 1990s, the IETF redefined the meaning of the 8-bit SERVICE TYPE field to accommodate a set of differentiated services (DS). Under the differentiated services interpretation, the first six bits comprise a codepoint, which is sometimes abbreviated DSCP, and the last two bits are left unused.
3-6. SNMP Configuration Any Network Management System (NMS) running the Simple Network Management Protocol (SNMP) can manage the Managed devices equipped with SNMP agent, provided that the Management Information Base (MIB) is installed correctly on the managed devices. The SNMP is a protocol that is used to govern the transfer of information between SNMP manager and agent and traverses the Object Identity (OID) of the management Information Base (MIB), described in the form of SMI syntax.
Default SNMP function : Enable Default community name for GET: public Default community name for SET: private Default community name for Trap: public Default Set function : Enable Default trap host IP address: 0.0.0.0 Default port number :162 Trap: In the switch, there are 6 trap hosts supported. Each of them has its own community name and IP address; is user-definable. To set up a trap host means to create a trap manager by assigning an IP address to host the trap message.
3-7. IGMP Snooping The function, IGMP Snooping, is used to establish the multicast groups to forward the multicast packet to the member ports, and, in nature, avoids wasting the bandwidth while IP multicast packets are running over the network. This is because a switch that does not support IGMP or IGMP Snooping can not tell the multicast packet from the broadcast packet, so it can only treat them all as the broadcast packet.
Parameter description: IGMP snooping mode selection: The switch supports three kinds of IGMP Snooping status, including “Passive”, “Active” and “Disable”. Disable: Set “Disable” mode to disable IGMP Snooping function. Default: Disable Active: In Active mode, IGMP snooping switch will periodically issue the Membership Query message to all hosts attached to it and gather the Membership report message to update the database of the Multicast table.
Function name: Allowed Group Function description: The Allowed Group function allows the IGMP Snooping to set up the IP multicast table based on user’s specific conditions. IGMP report packets that meet the items you set up will be joined or formed the multicast group. Fig. 3-26 Parameter description: IP Range: The switch supports two kinds of options for managed valid IP range, including “Any” and “Custom”. Default is “Any”. In case that” Custom” had been chosen, you can assigned effective IP range.
Add: A new entry of allowed group configuration can be created after the parameters as mentioned above had been setup and then press button. Edit: The existed entry also can be modified after pressing button. Delete: Remove the existed entry of allowed group configuration from the allowed group.
3-8. Max. Packet Length Function name: Max. Packet Length Function description: The switch is capable of dealing with 9k Jumbo Frames, which suits the transmission for a large amount of data in the network environment. Parameter description: Jumbo Frame(bytes): Set up the maximum length of the packet that each port of the switch can accept. Maximum length can be up to 1532 bytes or 9216 bytes. The default is 1532 bytes. Fig.
3-9. DHCP Boot The DHCP Boot function is used to spread the request broadcast packet into a bigger time frame to prevent the traffic congestion due to broadcast packets from many network devices which may seek its NMS, boot server, DHCP server and many connections predefined when the whole building or block lose the power and then reboot and recover.
3-10. VLAN The switch supports Tag-based VLAN (802.1q) and Port-based VLAN. Support 256 active VLANs and VLAN ID 1~4094. VLAN configuration is used to partition your LAN into small ones as your demand. Properly configuring it, you can gain not only improving security and increasing performance but greatly reducing VLAN management. 3-10-1.
Metro Mode: The Metro Mode is a quick configuration VLAN environment method on Port-based VLAN. It will create 22 or 23 Port-based VLAN groups. Double-tag: Double-tag mode belongs to the tag-based mode, however, it would treat all frames as the untagged ones, which means that tag with PVID will be added into all packets. Then, these packets will be forwarded as Tag-based VLAN. So, the incoming packets with tag will become the double-tag ones. Fig.
Up-link Port: This function is enabled only when metro mode is chosen in VLAN mode. 23: Except Port 23, each port of the switch cannot transmit packets with each other. Each port groups a VLAN with Port 23, thus, total 23 groups consisting of 2 members are formed. 24: Except Port 24, each port of the switch cannot transmit packets with each other. Each port groups a VLAN with Port 24, thus, total 23 groups consisting of 2 members are formed.
3-10-2. Tag-based Group Function name: Tag-based Group Configuration Function description: It shows the information of existed Tag-based VLAN Groups, You can also easily create, edit and delete a Tag-based VLAN group by pressing , and function buttons. User can add a new VLAN group by inputting a new VLAN name and VLAN ID. Parameter description: VLAN Name: The name defined by administrator is associated with a VLAN group. Valid letters are A-Z, a-z, 0-9, “ - “ and “_” characters.
Add Group: Create a new Tag-based VLAN. Input the VLAN name as well as VID, configure the SYM-VLAN function and choose the member by ticking the check box beside the port No., then, press the button to have the setting taken effect. Fig. 3-32 Delete Group: Just press the button to remove the selected group entry from the Tag-based group table. Fig.
3-10-3. Port-based Group Function name: Port-based Group Configuration Function description: It shows the information of the existed Port-based VLAN Groups. You can easily create, edit and delete a Port-based VLAN group by pressing , and function buttons. User can add a new VLAN group by inputting a new VLAN name. Parameter description: VLAN Name: The name defined by administrator is associated with a VLAN group. Valid letters are A-Z, a-z, 0-9, “ - “ and “_” characters.
Add Group: Create a new Port-based VLAN. Input the VLAN name and choose the member by ticking the check box beside the port No., then, press the button to have the setting taken effect. Fig. 3-35 Delete Group: Just press the button to remove the selected group entry from the Port-based group table. Fig. 3-36 Edit a group: Just select a group entry and press the button, then you can modify a group‘s description and member set.
3-10-4. Tag Rule Function name: Tag Rule Function description: In VLAN Tag Rule Setting, user can input VID number to each port. The range of VID number is from 1 to 4094. User also can choose ingress filtering rules to each port. There are two ingress filtering rules which can be applied to the switch. The Ingress Filtering Rule 1 is “forward only packets with VID matching this port’s configured VID”. The Ingress Filtering Rule 2 is “drop untagged frame”.
Role: This is an egress rule of the port. Here you can choose Access, Trunk or Hybrid. Trunk means the outgoing packets must carry VLAN tag header. Access means the outgoing packets carry no VLAN tag header. If packets have double VLAN tags, one will be dropped and the other will still be left. As to Hybrid, it is similar to Trunk, and both of them will tagout.
3-11. MAC Table MAC Table Configuration gathers many functions, including MAC Table Information, MAC Table Maintenance, Static Forward, Static Filter and MAC Alias, which cannot be categorized to some function type. They are described below. Function name: MAC Table Information Function Description: Display the static or dynamic learning MAC entry and the state for the selected port. Parameter description: Port: Select the port you would like to inquire.
Port: The port that exists in the searched MAC Entry. VID: VLAN Group that MAC Entry exists. State: Display the method that this MAC Entry is built. It may show “Dynamic MAC” or “Static MAC”. Fig.
Function Name: MAC Table Maintenance Function Description: This function can allow the user to set up the processing mechanism of MAC Table. An idle MAC address exceeding MAC Address Age-out Time will be removed from the MAC Table. The range of Age-out Time is 10-65535 seconds, and the setup of this time will have no effect on static MAC addresses. Parameter description: Aging Time: Delete a MAC address idling for a period of time from the MAC Table, which will not affect static MAC address.
Function Name: Static Forward Function Description: Static Forward is a function that allows the user in the static forward table to access a specified port of the switch. Static Forward table associated with a specified port of a switch is set up by manually inputting MAC address and its alias name. When a MAC address is assigned to a specific port, all of the switch’s traffics sent to this MAC address will be forwarded to this port.
Function name: Static Filter Function Description: Static Filter is a function that denies the packet forwarding if the packet’s MAC Address is listed in the filtering Static Filter table. User can very easily maintain the table by filling in MAC Address, VID (VLAN ID) and Alias fields individually. User also can delete the existed entry by clicking button. Parameter description: MAC: It is a six-byte long Ethernet hardware address and usually expressed by hex and separated by hyphens.
Function name: MAC Alias Function description: MAC Alias function is used to let you assign MAC address a plain English name. This will help you tell which MAC address belongs to which user in the illegal access report. At the initial time, it shows all pairs of the existed alias name and MAC address. There are three MAC alias functions in this function folder, including MAC Alias Add, MAC Alias Edit and MAC Alias Delete.
Parameter description: MAC Address: It is a six-byte long Ethernet hardware address and usually expressed by hex and separated by hyphens. For example, 00 – 40 - C7 - D6 – 00 - 01 Alias: MAC alias name you assign. Note: If there are too many MAC addresses learned in the table, we recommend you inputting the MAC address and alias name directly.
3-12. GVRP Configuration GVRP is an application based on Generic Attribute Registration Protocol (GARP), mainly used to automatically and dynamically maintain the group membership information of the VLANs. The GVRP offers the function providing the VLAN registration service through a GARP application. It makes use of GARP Information Declaration (GID) to maintain the ports associated with their attribute database and GARP Information Propagation (GIP) to communicate among switches and end stations.
Function name: GVRP Config Function description: In the function of GVRP Config, it is used to configure each port’s GVRP operation mode, in which there are seven parameters needed to be configured described below. Parameter description: GVRP State Setting: This function is simply to let you enable or disable GVRP function. You can pull down the list and click the arrow key to choose “Enable” or “Disable”. Then, click the button, the system will take effect immediately.
Normal: It is Normal Registration. The Registrar responds normally to incoming GARP messages. The default setting is Normal. Fixed: It is Registration Fixed. The Registrar ignores all GARP messages, and all members remain in the registered (IN) state. Forbidden: It is Registration Forbidden. The Registrar ignores all GARP messages, and all members remain in the unregistered (EMPTY) state. Restricted Mode: This function is used to restrict dynamic VLAN be created when this port received GVRP PDU.
Function name: GVRP Counter Function description: All GVRP counters are mainly divided into Received and Transmitted two categories to let you monitor the GVRP actions. Actually, they are GARP packets. Fig. 3-44 Parameter description: Received: Total GVRP Packets: Total GVRP BPDU is received by the GVRP application. Invalid GVRP Packets: Number of invalid GARP BPDU is received by the GARP application. LeaveAll Message Packets: Number of GARP BPDU with Leave All message is received by the GARP application.
LeaveEmpty Message Packets: Number of GARP BPDU with Leave Empty message is received by the GARP application. Empty Message Packets: Number of GARP BPDU with Empty message is received by the GARP application. Transmitted: Total GVRP Packets: Total GARP BPDU is transmitted by the GVRP application. Invalid GVRP Packets: Number of invalid GARP BPDU is transmitted by the GVRP application. LeaveAll Message Packets: Number of GARP BPDU with Leave All message is transmitted by the GARP application.
Function name: GVRP Group Information Function description: To show the dynamic group member and their information. Parameter description: VID: VLAN identifier. When GVRP group creates, each dynamic VLAN group owns its VID. Valid range is 1 ~ 4094. Member Port: Those are the members belonging to the same dynamic VLAN group. Edit Administrative Control: When you create GVRP group, you can use Administrative Control function to change Applicant Mode and Registrar Mode of GVRP group member.
3-13. STP Configuration The Spanning Tree Protocol (STP) is a standardized method (IEEE 802.1D) for avoiding loops in switched networks. When STP is enabled, ensure that only one path is active between any two nodes on the network at a time. User can enable Spanning Tree Protocol on switch’s web management and then set up other advanced items. We recommend that you enable STP on all switches to ensure a single active path on the network. 3-13-1.
All bridges in the LAN will re-learn and determine which the root bridge is. Maximum Age time is assigned by root bridge in unit of seconds. Default is 20 seconds. Current Forward Delay: Show the current root bridge forward delay time. The value of Forward Delay time is set by root. The Forward Delay time is defined as the time spent from Listening state moved to Learning state or from Learning state moved to Forwarding state of a port in bridge. Hello Time: Show the current hello time of the root bridge.
3-13-2. STP Configuration The STP, Spanning Tree Protocol, actually includes RSTP. In the Spanning Tree Configuration, there are six parameters open for the user to configure as user’s idea. Each parameter description is listed below. Function name: STP Configuration Function description: User can set the following Spanning Tree parameters to control STP function enable/disable, select mode RSTP/STP and affect STP state machine behavior to send BPDU in this switch.
Forward Delay: You can set the root bridge forward delay time. This figure is set by root bridge only. The forward delay time is defined as the time spent from Listening state moved to Learning state and also from Learning state moved to Forwarding state of a port in bridge. The forward delay time contains two states, Listening state to Learning state and Learning state to Forwarding state. It assumes that forward delay time is 15 seconds, then total forward delay time will be 30 seconds.
3-13-3. STP Port Configuration Function name: STP Port Setting Function description: In the STP Port Setting, one item selection and five parameters settings are offered for user’s setup. User can disable and enable each port by selecting each Port Status item. User also can set “Path Cost” and “Priority” of each port by filling in the desired value and set “Admin Edge Port” and “Admin Point To Point” by selecting the desired item. Parameter description: Port Status: It displays the current state of a port.
802.1w RSTP recommended value: (Valid range: 1 – 200,000,000) 10 Mbps : 2,000,000 100 Mbps : 200,000 1 Gbps : 20,000 Default: 0 Priority: Priority here means Port Priority. Port Priority and Port Number are mixed to form the Port ID. Port IDs are often compared in order to determine which port of a bridge would become the Root Port. The range is 0 – 240. Default is 128. Admin Edge Port: If user selects “Yes”, this port will be an edge port.
M Check: Migration Check. It forces the port sending out an RSTP BPDU instead of a legacy STP BPDU at the next transmission. The only benefit of this operation is to make the port quickly get back to act as an RSTP port. Click button to send a RSTP BPDU from the port you specified. Fig.
3-14. Trunking Configuration The Port Trunking Configuration is used to configure the settings of Link Aggregation. You can bundle more than one port with the same speed, full duplex and the same MAC to be a single logical port, thus the logical port aggregates the bandwidth of these ports. This means you can apply your current Ethernet equipments to build the bandwidth aggregation.
Per Trunking Group supports a maximum of 12 ready member-ports. Please note that some decisions will automatically be made by the system while you are configuring your trunking ports. Some configuration examples are listed below: a) 12 ports have already used Static Trunk Group ID 1, the 13th port willing to use the same Static Trunk Group ID will be automatically set to use the “None” trunking method and its Group ID will turn to 0. This means the port won’t aggregate with other ports.
Function name: Port Setting/Status Function description: Port setting/status is used to configure the trunk property of each and every port in the switch system. Parameter description: Method: This determines the method a port uses to aggregate with other ports. None: A port does not want to aggregate with any other port should choose this default setting. LACP: A port use LACP as its trunk method to get aggregated with other ports also using LACP.
Aggtr: Aggtr is an abbreviation of “aggregator”. Every port is also an aggregator, and its own aggregator ID is the same as its own Port No. We can regard an aggregator as a representative of a trunking group. Ports with same Group ID and using same trunking method will have the opportunity to aggregate to a particular aggregator port. This aggregator port is usually the port with the smallest Port No. within the trunking group.
Function name: Aggregator View Function description: To display the current port trunking information from the aggregator point of view. Parameter description: Aggregator: It shows the aggregator ID (from 1 to 24) of every port. In fact, every port is also an aggregator, and its own aggregator ID is the same as its own Port No.. Method: Show the method a port uses to aggregate with other ports. Member Ports: Show all member ports of an aggregator (port).
Function name: LACP Detail (LACP Aggregator Detailed Information) Function description: Show the detailed information of the LACP trunking group. Parameter description: Actor: The switch you are watching on. Partner: The peer system from this aggregator’s view. System Priority: Show the System Priority part of a system ID. MAC Address: Show the MAC Address part of a system ID. Port: Show the port number part of an LACP port ID. Key: Show the key value of the aggregator.
Function name: LACP System Priority Function description: It is used to set the priority part of the LACP system ID. LACP will only aggregate together the ports whose peer link partners are all on a single system. Each system supports LACP will be assigned a globally unique System Identifier for this purpose. A system ID is a 64-bit field comprising a 48-bit MAC Address and 16-bit priority value. The System Priority can be set by the user. Its range is from 1 to 65535. Default: 32768 Fig.
3-15. 802.1X Configuration 802.1X port-based network access control provides a method to restrict users to access network resources via authenticating user’s information. This restricts users from gaining access to the network resources through a 802.1Xenabled port without authentication. If a user wishes to touch the network through a port under 802.
The overview of operation flow for the Fig. 3-53 is quite simple. When Supplicant PAE issues a request to Authenticator PAE, Authenticator and Supplicant exchanges authentication message. Then, Authenticator passes the request to RADIUS server to verify. Finally, RADIUS server replies if the request is granted or denied.
Authentication server C Fig. 3-54 Authenticator B Supplicant A The Fig. 3-55 shows the procedure of 802.1X authentication. There are steps for the login based on 802.1X port access control management. The protocol used in the right side is EAPOL and the left side is EAP. 1. At the initial stage, the supplicant A is unauthenticated and a port on switch acting as an authenticator is in unauthorized state. So the access is blocked in this stage. 2. Initiating a session.
8. If user ID and password is correct, the authentication server will send a Radius-Access-Accept to the authenticator. If not correct, the authentication server will send a Radius-Access-Reject. 9. When the authenticator PAE receives a Radius-Access-Accept, it will send an EAP-Success to the supplicant. At this time, the supplicant is authorized and the port connected to the supplicant and under 802.1X control is in the authorized state.
Only MultiHost 802.1X is the type of authentication supported in the switch. In this mode, for the devices connected to this port, once a supplicant is authorized, the devices connected to this port can access the network resource through this port. 802.1X Port-based Network Access Control function supported by the switch is little bit complex, for it just support basic Multihost mode, which can distinguish the device’s MAC address and its VID.
Function name: 802.1X State Setting Function description: This function is used to configure the global parameters for RADIUS authentication in 802.1X port security application. Parameter description: Radius Server: RADIUS server IP address for authentication. Default: 192.168.1.1 Port Number: The port number to communicate with RADIUS server for the authentication service. The valid value ranges 1-65535. Default port number is 1812.
Function name: 802.1X Mode Setting Function description: Set the operation mode of 802.1X for each port. In this device, it supports only Multi-host operation mode. Parameter description: Port Number: Indicate which port is selected to configure the 802.1X operation mode. 802.1X Mode: 802.1X operation mode. There are two options, including Disable and Multi-host mode. Default is Disable. Disable It will have the chosen port acting as a plain port, that is no 802.1X port access control works on the port.
Function name: Port Security Management Function description: Shows each port status. In Multihost mode, it shows the port number and its status, authorized or unauthorized. Parameter description: Disable Mode: When selecting Disable mode for a port in the function 802.1X Port Mode Configuration, the port is in the uncontrolled port state and does not apply 802.1X authenticator on it. Any node attached on this port can access the network without the admittance of 802.1X authenticator.
Function name: Param. Setting Function description: This function is used to configure the parameters for each port in 802.1X port security application. Refer to the following parameters description for details. Parameter description: Port: It is the port number to be selected for configuring its associated 802.1X parameters which are Port control, reAuthMax, txPeriod, Quiet Period, reAuthEnabled, reAuthPeriod, max. Request, suppTimeout, serverTimeout and Controlled direction.
reAuthEnabled: Choose whether regular authentication will take place in this port. Default: ON reAuthPeriod(1-65535 s): A non-zero number seconds between the periodic re-authentication of the supplicant. Default: 3600 max. Request(1-10): The maximum of number times that the authenticator will retransmit an EAP Request to the supplicant before it times out the authentication session. The valid range: 1 – 10.
3-16. Alarm Configuration Alarm Configuration Events Configuration Email/SMS Configuration Function name: Events Configuration Function description: The Trap Events Configuration function is used to enable the switch to send out the trap information while pre-defined trap events occurred. The switch offers 23 different trap events to users for switch management. The trap information can be sent out in three ways, including email, mobile phone SMS (short message system) and trap.
Fig. 3-60 Function name: Email/SMS Configuration Function description: Alarm configuration is used to configure the persons who should receive the alarm message via either email or SMS, or both. It depends on your settings. An email address or a mobile phone number has to be set in the web page of alarm configuration (See Fig. 3-61). Then, user can read the trap information from the email or the mobile phone. This function provides 6 email addresses and 6 mobile phone numbers at most.
Parameter description: Email: Mail Server: the IP address of the server transferring your email. Username: your username on the mail server. Password: your password on the mail server. Email Address 1 – 6: email address that would like to receive the alarm message. SMS: SMS Server: the IP address of the server transferring your SMS. Username: your username in ISP. Password: your username in ISP. Mobile Phone 1-6: the mobile phone number that would like to receive the alarm message. Fig.
3-17. Configuration The switch supports three copies of configuration, including the default configuration, working configuration and user configuration for your configuration management. All of them are listed and described below respectively. Default Configuration: This is the ex-factory setting and cannot be altered. In Web UI, two restore default functions are offered for the user to restore to the default setting of the switch.
3-17-1. Save/Restore Function name: Save As Start Configuration Function description: Save the current configuration as a start configuration file in flash memory. Fig. 3-63 Function name: Save As User Configuration Function description: Save the current configuration as a user configuration file in flash memory.
Fig.
Function name: Restore Default Configuration (includes default IP address) Function description: Restore Default Configuration function can retrieve the ex-factory setting to replace the start configuration. And the IP address of the switch will also be restored to 192.168.1.1. Fig. 3-65 Function name: Restore Default Configuration (excludes current IP address) Function description: Restore Default Configuration function can retrieve the ex-factory setting to replace the start configuration.
Fig.
Function name: Restore User Configuration Function description: Restore User Configuration function can retrieve the previous confirmed working configuration stored in the flash memory to update start configuration. When completing to restore the configuration, the system’s start configuration is updated and will be changed its system settings after rebooting the system. Fig.
3-17-2. Config File Function name: Config File Function description: With this function, user can back up or reload the config files of Save As Start or Save As User via TFTP. Parameter description: Export File Path: Export Start: Export Save As Start’s config file stored in the flash. Export User-Conf: Export Save As User’s config file stored in the flash. Import File Path: Import Start: Import Save As Start’s config file stored in the flash.
3-18. Diagnostics Three functions, including Diagnostics, Loopback Test and Ping Test are contained in this function folder for device self-diagnostics. Each of them will be described in detail orderly in the following sections. Diagnostics Diagnostics Loopback Test Ping Test Function name: Diagnostics Function description: Diagnostics function provides a set of basic system diagnosis. It let users know that whether the system is health or needs to be fixed.
Function name: Loopback Test Function description: In the Loopback Test function, there are two different loopback tests. One is Internal Loopback Test and the other is External Loopback Test. The former test function will not send the test signal outside the switch box. The test signal only wraps around in the switch box. As to the latter test function, it will send the test signal to its link partner. If you do not have them connected to active network devices, i.e.
Function name: Ping Test Function description: Ping Test function is a tool for detecting if the target device is alive or not through ICMP protocol which abounds with report messages. The switch provides Ping Test function to let you know that if the target device is available or not. You can simply fill in a known IP address and then click button. After a few seconds later, the switch will report you the pinged device is alive or dead in the field of Ping Result.
3-19. TFTP Server Function name: TFTP Server Function description: Set up IP address of TFTP server. Parameter description: Specify the IP address where the TFTP server locates. Fill in the IP address of your TFTP server, then press button to have the setting taken effect. Fig.
3-20. Log This function shows the log data. The switch provides system log data for users. There are 18 private trap logs, 5 public trap logs. The switch supports total 120 log entries. For more details on log items, please refer to the section of Trap/Alarm Configuration and SNMP Configuration. Function name: Log Data Function description: The Trap Log Data is displaying the log items including all SNMP Private Trap events, SNMP Public traps and user logs occurred in the system. In the report table, No.
Upload Log: Upload log data through tftp. Clear Log: Clear log data.
3-21. Firmware Upgrade Software upgrade tool is used to help upgrade the software function in order to fix or improve the function. The switch provides a TFTP client for software upgrade. This can be done through Ethernet. Function name: Firmware Upgrade Function description: The switch supports TFTP upgrade tool for upgrading software. If you assure to upgrade software to a newer version one, you must follow two procedures: 1.) Specifying the IP address where TFTP server locates.
3-22. Reboot We offer you many ways to reboot the switch, including power up, hardware reset and software reset. You can press the RESET button in the front panel to reset the switch. After upgrading software, changing IP configuration or changing VLAN mode configuration, then you must reboot to have the new configuration taken effect. Here we are discussing is software reset for the “reboot” in the main menu. Function name: Reboot Function description: Reboot the switch.
3-23. Logout You can manually logout by performing Logout function. In the switch, it provides another way to logout. You can configure it to logout automatically. Function name: Logout Function description: The switch allows you to logout the system to prevent other users from the system without the permission. If you do not logout and exit the browser, the switch will automatically have you logout.
4. Operation of CLI Management 4-1. CLI Management Refer to Chapter 2 for basic installation. The following description is the brief of the network connection. -- Locate the correct DB-9 null modem cable with female DB-9 connector. Null modem cable comes with the management switch. Refer to the Appendix B for null modem cable configuration. -- Attach the DB-9 female connector to the male DB-9 serial port connector on the Management board.
Fig. 4-1 Fig.
4-2. Commands of CLI To see the commands of the mode, please input “?” after the prompt, then all commands will be listed in the screen. All commands can be divided into two categories, including global commands and local commands. Global commands can be used wherever the mode you are. They are “exit”, “end”, “help”, “history”, “logout”, “save start”, “save user”, “restore default” and “restore user”. For more details, please refer to Section 4-2-1.
4-2-1. Global Commands of CLI end Syntax: end Description: Back to the top mode. When you enter this command, your current position would move to the top mode. If you use this command in the top mode, you are still in the position of the top mode. Argument: None. Possible value: None. Example: SNMP-GSH2416# alarm SNMP-GSH2416(alarm)# events SNMP-GSH2416(alarm-events)# end SNMP-GSH2416# exit Syntax: exit Description: Back to the previous mode.
help Syntax: help Description: To show available commands. Some commands are the combination of more than two words. When you enter this command, the CLI would show the complete commands. Besides, the command would help you classify the commands between the local commands and the global ones. Argument: None. Possible value: None.
history Syntax: history [#] Description: To show a list of previous commands that you had ever run. When you enter this command, the CLI would show a list of commands which you had typed before. The CLI supports up to 256 records. If no argument is typed, the CLI would list total records up to 256. If optional argument is given, the CLI would only show the last numbers of records, given by the argument. Argument: [#]: show last number of history records. (optional) Possible value: [#]: 1, 2, 3, ….
logout Syntax: logout Description: When you enter this command via Telnet connection, you would logout the system and disconnect. If you connect the system through direct serial port with RS-232 cable, you would logout the system and be back to the initial login prompt when you run this command. Argument: None. Possible value: None.
restore user Syntax: restore user Description: To restore the startup configuration as user defined configuration. If restoring default successfully, the CLI would prompt if reboot immediately or not. If you press Y or y, the system would reboot immediately; others would back to the CLI system. After restoring user-defined configuration, all the changes in the startup configuration would be lost. After rebooting, the entire startup configuration would replace as user defined one. Argument: None.
save user Syntax: save user Description: To save the current configuration as the user-defined configuration. When you enter this command, the CLI would save your current configuration into the non-volatile FLASH as user-defined configuration. Argument: None. Possible value: None. Example: SNMP-GSH2416# save user Saving user...
4-2-2. Local Commands of CLI 802.1X set max-request Syntax: set max-request Description: The maximum number of times that the state machine will retransmit an EAP Request packet to the Supplicant before it times out the authentication session. Argument: : syntax 1,5-7, available from 1 to 24 : max-times , range 1-10 Possible value: : 1 to 24 : 1-10, default is 2 Example: SNMP-GSH2416(802.
set port-control Syntax: set port-control Description: To set up 802.1X status of each port. Argument: : syntax 1,5-7, available from 1 to 24 : Set up the status of each port 0:ForceUnauthorized 1:ForceAuthorized 2:Auto Possible value: : 1 to 24 : 0, 1 or 2 Example: SNMP-GSH2416(802.
Syntax: set reAuthMax Description: The number of reauthentication attempts that are permitted before the port becomes Unauthorized. Argument: : syntax 1,5-7, available from 1 to 24 : max. value , range 1-10 Possible value: : 1 to 24 : 1-10, default is 2 Example: SNMP-GSH2416(802.
set state Description: To configure the settings related with 802.1X Radius Server. Argument: : the IP address of Radius Server : the service port of Radius Server(Authorization port) : set up the value of secret-key, and the length of secret-key is from 1 to 31 Possible value: : 1~65535, default is 1812 Example: SNMP-GSH2416(802.1X)# set state 192.168.1.
To display the mode of each port. Argument: None. Possible value: None. Example: SNMP-GSH2416(802.1X)# show mode Port Mode ====== ============ 1 Disable 2 Multi-host 3 Disable 4 Disable 5 Disable 6 Disable : : : show parameter Syntax: show parameter Description: To display the parameter settings of each port. Argument: None. Possible value: None. Example: SNMP-GSH2416(802.1X)# show parameter port 1) port control : Auto reAuthMax : 2 txPeriod : 30 Quiet Period : 60 reAuthEnabled : ON reAuthPeriod : 3600 max.
port 2) port control reAuthMax txPeriod Quiet Period reAuthEnabled reAuthPeriod max. Request suppTimeout serverTimeout : : : show security : : : : : : : : : Auto 2 30 60 ON 3600 2 30 30 Syntax: show security Description: To display the authentication status of each port. Argument: None. Possible value: None. Example: SNMP-GSH2416(802.
add Syntax: add Description: To create a new guest user. When you create a new guest user, you must type in password and confirm password. Argument: : new account name Possible value: A string must be at least 5 character. Example: SNMP-GSH2416(account)# add aaaaa Password: Confirm Password: Save Successfully SNMP-GSH2416(account)# del Syntax: del Description: To delete an existing account. Argument: : existing user account Possible value: None.
modify Syntax: modify Description: To change the username and password of an existing account. Argument: : existing user account Possible value: None. Example: SNMP-GSH2416(account)# modify aaaaa username/password: the length is from 5 to 15. Current username (aaaaa):bbbbb New password: Confirm password: Username changed successfully. Password changed successfully. show Syntax: show Description: To show system account, including account name and identity. Argument: None. Possible value: None.
alarm <> del mail-address Syntax: del mail-address <#> Description: To remove the configuration of E-mail address. Argument: <#>: email address number, range: 1 to 6 Possible value: <#>: 1 to 6 Example: SNMP-GSH2416(alarm-email)# del mail-address 2 del server-user Syntax: del server-user Description: To remove the configuration of server, user account and password. Argument: None. Possible value: None.
set server Syntax: set server Description: To set up the IP address of the email server. Argument: :email server ip address or domain name Possible value: None. Example: SNMP-GSH2416(alarm-email)# set server 192.168.1.6 set user Syntax: set user Description: To set up the account and password of the email server. Argument: : email server account and password Possible value: None.
<> del all Syntax: del all Description: To disable email, sms and trap of events. Argument: :del the range of events, syntax 1,5-7 Possible value: : 1~23 Example: SNMP-GSH2416(alarm-events)# del all 1-3 del email Syntax: del email Description: To disable the email of the events.
del trap Syntax: del trap Description: To disable the trap of the events. Argument: :del the range of trap, syntax 1,5-7 Possible value: : 1~23 Example: SNMP-GSH2416(alarm-events)# del trap 1-3 set all Syntax: set all Description: To enable email, sms and trap of events.
set sms Syntax: set sms Description: To enable the sms of the events. Argument: :set the range of sms, syntax 1,5-7 Possible value: : 1~23 Example: SNMP-GSH2416(alarm-events)# set sms 1-3 set trap Syntax: set trap Description: To enable the trap of the events. Argument: :set the range of trap, syntax 1,5-7 Possible value: : 1~23 Example: SNMP-GSH2416(alarm-events)# set trap 1-3 show Syntax: show Description: To display the configuration of alarm event.
Example: SNMP-GSH2416(alarm-events)# show Events Email SMS Trap ----------------------------------------1 Cold Start v 2 Warm Start v 3 Link Down v 4 Link Up v 5 Authentication Failure v 6 User Login 7 User Logout 8 STP Topology Changed 9 STP Disabled 10 STP Enabled 11 LACP Disabled 12 LACP Enabled 13 LACP Member Added 14 LACP Port Failure 15 GVRP Disabled 16 GVRP Enabled 17 VLAN Disabled 18 Port-based Vlan Enabled 19 Tag-based Vlan Enabled 20 Metro-mode Vlan Enabled 21 Double-tag Vlan Enabled 22 Module Ins
show (alarm) Syntax: show Description: The Show for alarm here is used to display the configuration of Trap, SMS or E-mail. Argument: None. Possible value: None. Example: SNMP-GSH2416(alarm)# show events SNMP-GSH2416(alarm)# show email SNMP-GSH2416(alarm)# show sms <> del phone-number Syntax: del phone-number <#> Description: To delete sms phone number.
set phone-number Syntax: set phone-number <#> Description: To add sms phone number. Argument: <#>: mobile phone number, range: 1 to 6 : phone number Possible value: <#>: 1 to 6 Example: SNMP-GSH2416(alarm-sms)# set phone-number 1 0968777777 set server Syntax: set server Description: To set up the IP address of sms server. Argument: : SMS server ip address or domain name Possible value: None. Example: SNMP-GSH2416(alarm-sms)# set server 192.168.1.
show Syntax: show Description: To display the configuration of SMS trap event. Argument: None. Possible value: None. Example: SNMP-GSH2416(alarm-sms)# show SMS Server : 192.168.1.7 Username : ABC Password : **************** Mobile Phone 1: 0968777777 Mobile Phone 2: Mobile Phone 3: Mobile Phone 4: Mobile Phone 5: Mobile Phone 6: autologout autologout Syntax: autologout
bandwidth disable egress-rate Syntax: disable egress-rate Description: To cancel the egress-rate of the port. Argument: :syntax 1,5-7, available from 1 to 24 Possible value: : 1 to 24 Example: SNMP-GSH2416(bandwidth)# disable egress-rate 1-8 disable ingress-rate Syntax: disable ingress-rate Description: To cancel the Ingress-rate of the port.
enable egress-rate Syntax: enable egress-rate Description: To set up the egress-rate of the port. Argument: :syntax 1,5-7, available from 1 to 24 : 0-1000 Possible value: : 1 to 24 : 0-1000 Example: SNMP-GSH2416(bandwidth)# enable egress-rate 1-16 200 enable ingress-rate Syntax: enable ingress-rate Description: To set up the Ingress-rate of the ports.
show Syntax: show Description: To display all current settings of the bandwidth. Argument: None. Possible value: None.
config-file export start Syntax: export start Description: To run the export start function. Argument: None. Possible value: None. Example: SNMP-GSH2416(config-file)# export start Export successful. export user-conf Syntax: export user-conf Description: To run the export user-conf function. Argument: None Possible value: None Example: SNMP-GSH2416(config-file)# export user-conf Export successful. import start Syntax: import start Description: To run the import start function. Argument: None.
import user-conf Syntax: import user-conf Description: To run the import user-conf function. Argument: None. Possible value: None. Example: SNMP-GSH2416(config-file)# import user-conf Import successful. set export-path Syntax: set export-path Description: To set up the filepath and filename that will be exported. Argument: :filepath and filename Possible value: :filepath and filename Example: SNMP-GSH2416(config-file)# set export-path log/21511.
show Syntax: show Description: To display the config-file information. Argument: None. Possible value: None. Example: SNMP-GSH2416(config-file)# show TFTP Server IP Address: 192.168.3.111 Export Path and Filename: nmap/123.ts Import Path and Filename: user123.
dhcp-boot set dhcp-boot Syntax: set dhcp-boot Description: To set up the delay time for DHCP Boot. Argument: :range syntax: 0, 1-30. The value “0” is to disable dhcp-boot delay Possible value: :0-30 Example: SNMP-GSH2416(dhcp-boot)# set dhcp-boot 30 show Syntax: show Description: To display the status of DHCP Boot. Argument: None. Possible value: None.
diag diag Syntax: diag Description: Diag is used to test whether UART, DRAM, Flash and EEPROM is normal or not. Argument: None. Possible value: None. Example: SNMP-GSH2416(diag)# diag EEPROM Test : OK UART Test : OK DRAM Test : OK Flash Test : OK loopback Syntax: Loopback Description: For Internal/External Loopback Test. Argument: None. Possible value: None.
firmware set upgrade-path Syntax: set upgrade-path Description: To set up the image file that will be upgraded. Argument: : upgrade file path Possible value: : upgrade file path Example: SNMP-GSH2416(firmware)# set upgrade-path gs2124c_SNMPGSH2416_v2.03.img show Syntax: show Description: To display the information of tftp server and upgrade-path. Argument: None. Possible value: None. Example: SNMP-GSH2416(firmware)# show TFTP Server IP Address: 192.168.3.
gvrp disable Syntax: disable Description: To disable the gvrp function. Argument: None. Possible value: None. Example: SNMP-GSH2416(gvrp)# disable enable Syntax: enable Description: To enable the gvrp function. Argument: None. Possible value: None. Example: SNMP-GSH2416(gvrp)# enable group Syntax: group Description: To enter any of gvrp group for changing gvrp group setting. You can change the applicant or registrar mode of existing gvrp group per port.
SNMP-GSH2416(gvrp)# group 2 SNMP-GSH2416(gvrp-group-2)# set applicant 1-6 non-participant SNMP-GSH2416(gvrp-group-2)# show GVRP group VID: 2 Port Applicant Registrar ---- --------------- --------1 Non-Participant Normal 2 Non-Participant Normal 3 Non-Participant Normal 4 Non-Participant Normal 5 Non-Participant Normal 6 Non-Participant Normal 7 Normal Normal 8 Normal Normal 12 Normal Normal 13 Normal Normal : : 23 Normal Normal 24 Normal Normal SNMP-GSH2416(gvrp-group-2)# set registrar 1-10 fixed SNMP-GSH2
set applicant Syntax: set applicant Description: To set default applicant mode for each port.
set restricted Syntax: set restricted Description: To set the restricted mode for each port.
set timer Syntax: set timer Description: To set gvrp join time, leave time, and leaveall time for each port. Argument: : port range, syntax 1,5-7, available from 1 to 24 : join timer, available from 20 to 100 : leave timer, available from 60 to 300 : leaveall timer, available from 1000 to 5000 Leave Time must equal double Join Time at least.
show counter Syntax: show counter Description: To display the counter number of the port.
hostname hostname Syntax: hostname Description: To set up the hostname of the switch. Argument: : hostname, max. 40 characters. Possible value: : hostname, max. 40 characters. Example: SNMP-GSH2416# hostname Company Company# igmp-snooping add allowed-group Syntax: add allowed-group Description: To add the entry of allowed IP multicast group. Argument: : the range of IP multicast. : vlan ID. 0-4094 or any.
set mode Syntax: set mode Description: To set up the mode of IGMP Snooping. Argument: : 0:disable, 1:active, 2:passive Possible value: : 0,1or 2 Example: SNMP-GSH2416(igmp-snooping)# set mode 2 show igmp-snooping Syntax: show igmp-snooping Description: To display IGMP snooping mode and allowed IP multicast entry. Argument: None. Possible value: None. Example: SNMP-GSH2416(igmp-snooping)# show igmp-snooping Snoop Mode: Active IP Multicast: 1) IP Address : 224.1.1.
IP disable dhcp Syntax: disable dhcp Description: To disable the DHCP function of the system. Argument: None. Possible value: None. Example: SNMP-GSH2416(ip)# disable dhcp enable dhcp Syntax: enable dhcp Description: To enable the system DHCP function and set DNS server via manual or auto mode. Argument: : set dhcp by using manual or auto mode.
set ip Syntax: set ip Description: To set the system IP address, subnet mask and gateway. Argument: : ip address : subnet mask : default gateway Possible value: : 192.168.1.2 or others : 255.255.255.0 or others : 192.168.1.253 or others Example: SNMP-GSH2416(ip)# set ip 192.168.1.2 255.255.255.0 192.168.1.
log clear Syntax: clear Description: To clear the log data. Argument: None. Possible value: None. Example: SNMP-GSH2416(log)# clear disable auto-upload Syntax: disable auto-upload Description: To disable the auto-upload function. Argument: None. Possible value: None. Example: SNMP-GSH2416(log)# disable auto-upload enable auto-upload Syntax: enable auto-upload Description: To enable the auto-upload function. Argument: None. Possible value: None.
show Syntax: show Description: To show a list of trap log events. When any of log events happens, it will be recorded and using show command in log function to query. Up to 120 log records are supported. Argument: None. Possible value: None. Example: SNMP-GSH2416(log)# show Tftp Server : 0.0.0.
mac-table <> del Syntax: del Description: To delete the mac alias entry. Argument: : mac address, format: 00-02-03-04-05-06 Possible value: : mac address Example: SNMP-GSH2416(mac-table-alias)# del 00-44-33-44-55-44 set Syntax: set Description: To set up the mac alias entry. Argument: : mac address, format: 00-02-03-04-05-06 : mac alias name, max. 15 characters Possible value: None.
search Syntax: search Description: To look for the relative mac information in mac table.
<> set aging Syntax: set aging <#> Description: To set up the age out time of dynamic learning mac. Argument: <#>: age-timer in seconds, 0, 10 to 65535. The value “0” means to disable aging Possible value: <#>: 0, 10 to 65535. Example: SNMP-GSH2416(mac-table-maintain)# set aging 300 set flush Syntax: set flush Description: To delete all of the MACs that is learned dynamically. Argument: None. Possible value: None.
<> add Syntax: add [alias] Description: To add the static mac entry. Argument: : mac address, format: 00-02-03-04-05-06 : 0-24. The value “0” means this entry is filtering entry : vlan id. 0, 1-4094. VID must be zero if vlan mode is not tag-based [alias] : mac alias name, max.
show filter Syntax: show filter Description: To display the static filter table. Argument: None. Possible value: None. Example: SNMP-GSH2416(mac-table-static-mac)# show filter Static Filtering Etnry: (Total 1 item(s)) 1) mac: 00-33-03-04-05-06, vid: -, alias: ccc show forward Syntax: show forward Description: To display the static forward table. Argument: None. Possible value: None.
management add Syntax: Usage: set [ ] [ ] [ ] [ ] [ ] Synopsis: set name Mary vid 20 ip 192.168.1.1-192.168.1.90 port 2-5,8 type h,s action a Synopsis: set name Mary vid 20 ip 192.168.1.1-192.168.1.90 Description: To save the adding management policy records.
delete Syntax: delete # Description: To delete a specific record or range. Argument: <#>: a specific or range management security entry(s) Possible value: None. Example: SNMP-GSH2416(management)# show #: 1 Name : Tom Type : SNMP VlanID : 2 Action : Deny IP : 192.168.1.30-192.168.1.
edit [#]: the specific management policy entry. Available range: 1 to 65536. Syntax: Usage: set [ ] [ ] [ ] [ ] [ ] Synopsis: set name Mary vid 20 ip 192.168.1.1-192.168.1.90 port 2-5,8 type h,s action a Synopsis: set name Mary vid 20 ip 192.168.1.1-192.168.1.90 Description: To edit management policy record. Argument: [ ] ACL entry name. [ ] VLAN ID. [ ] IP Range.
show Syntax: show Description: To show the specific management policy record. Argument: None. Possible value: None. Example: SNMP-GSH2416(management)# show #: 1 Name : Tom Type : SNMP VlanID : 2 Action : Deny 200 IP : 192.168.1.30-192.168.1.
max-pkt-len set len Syntax: set len Description: To set up the maximum length of the packet that each port of the switch can accept. Argument: : port range, syntax 1,5-7, available from 1 to 24 : maximum packet length Possible value: : 1 to 24 : 1518/1532/9216 Example: SNMP-GSH2416(max-pkt-len)# set len 1-8 9216 show Syntax: show Description: To show current setting of maximum packet length setting. Argument: None. Possible value: None.
mirror set mirror-mode Syntax: set mirror-mode Description: To set up the mode of mirror (rx mode or disable). Argument: : rx : enable the mode of mirror(Only mirror the packets that is received) disable: end the function of mirror Possible value: : rx or disable Example: SNMP-GSH2416(mirror)# set mirror-mode rx set monitored-port Syntax: set monitored-port Description: To set up the port that will be monitored.
show Syntax: show Description: To display the setting status of Mirror function. Argument: None. Possible value: None.
port clear counter Syntax: clear counter Description: To clear all ports’ counter (include simple and detail port counter) information. Argument: None. Possible value: None. Example: SNMP-GSH2416 (port)# clear counter disable flow-control Syntax: disable flow-control Description: To disable the flow control function of the port.
enable flow-control Syntax: enable flow-control Description: To enable the flow control function of the port. Argument: : syntax 1,5-7, available from 1 to 24 Possible value: : 1 ~ 24 Example: SNMP-GSH2416 (port)# enable flow-control 3-8 enable state Syntax: enable state Description: To enable the communication capability of the port.
show conf Syntax: show conf Description: To display the each port’s configuration about state, speed-duplex and flow control. Argument: None. Possible value: None. Example: SNMP-GSH2416 (port)# show conf show detail-counter Syntax: show detail-counter <#> Description: To display the detailed counting number of each port’s traffic.
Port 9 SFP information --------------------------------------------------------------------Connector Type : SFP - LC Fiber Type : Multi-mode (MM) Tx Central Wavelength : 850 Baud Rate : 1G Vendor OUI : 00:40:c7 Vendor Name : APAC Opto Vendor PN : KM28-C3S-TC-N Vendor Rev : 0000 Vendor SN : 5425010728 Date Code : 050530 Temperature : none Vcc : none Mon1 (Bias) mA : none Mon2 (TX PWR) : none Mon3 (RX PWR) : none show simple-counter Syntax: show simple-counter Description: To display the summary counting of
qos set advance-layer4 Syntax: set advance-layer4 <#> Description: To set class of ports on advanced mode of Layer 4 qos. Argument: : port range, syntax 1,5-7, available from 1 to 24 <#>: special UDP/TCP port selection, range: 1-10 : 0-65535. : default class (all other TCP/UDP ports). 1: high, 0: low : special TCP/UDP class.
set diffserv Syntax: set diffserv Description: To set class of ports on IP DiffServe qos. Argument: : dscp field, syntax 1,5-7, available from 0 to 63 : class of service setting. 1: high, 0: low Possible value: : 0 to 63 : 1or 0 Example: SNMP-GSH2416(qos)# set diffserv 0-20 1 set mode Syntax: set mode Description: To set qos priority mode of the switch.
set pri-tag Syntax: set pri_tag Description: To set class of ports on vlan tag-based qos. Argument: : port range, syntax 1,5-7, available from 1 to 24 : tag priority level, syntax: 1,5-7, available from 0 to 7 : class of service setting.
set tos Syntax: set tos Description: To set class of ports on IP TOS qos. Argument: : port range, syntax: 1,5-7, available from 1 to 24 : tos precedence field, syntax 1,5-7, available from 0 to 7 : class of service setting. 1: high, 0: low Possible value: : 1 to 24 : 0 to 7 : 1or 0 Example: SNMP-GSH2416(qos)# set tos 1-5 0-3 0 show Syntax: show Description: To display the information of the mode you choose.
reboot reboot Syntax: reboot Description: To reboot the system. Argument: None. Possible value: None. Example: SNMP-GSH2416# reboot snmp disable Syntax: disable set-ability disable snmp Description: The Disable here is used for the de-activation of snmp or set-community. Argument: None. Possible value: None.
set Syntax: set get-community set set-community set trap <#> [port] [community] Description: The Set here is used for the setup of get-community, set-community, trap host ip, host port and trap-community.
stp MCheck Syntax: MCheck Description: To force the port to transmit RST BPDUs. Argument: : syntax 1,5-7, available from 1 to 24 Possible value: : 1 to 24 Example: SNMP-GSH2416(stp)# Mcheck 1-8 disable Syntax: disable Description: To disable the STP function. Argument: None. Possible value: None. Example: SNMP-GSH2416(stp)# disable enable Syntax: enable Description: To enable the STP function. Argument: None. Possible value: None.
set config Syntax: set config Description: To set up the parameters of STP. Argument: :priority must be a multiple of 4096, available from 0 to 61440. : available from 1 to 10. : available from 6 to 40. : available from 4 to 30. Note: 2*(Forward Delay -1) >= Max Age Max Age >= 2*(Hello Time +1) Possible value: : 0 to 61440 : 1 to 10
set version Syntax: set version Description: To set up the version of STP. Argument: :stp / rstp Possible value: :stp / rstp Example: SNMP-GSH2416(stp)# set version rstp show config Syntax: show config Description: To display the configuration of STP. Argument: None. Possible value: None. Example: SNMP-GSH2416(stp)# show config STP State Configuration : Spanning Tree Protocol : Enabled Bridge Priority (0-61440) : 61440 Hello Time (1-10 sec) : 2 Max.
show port Syntax: show port Description: To display the port information of STP. Argument: None. Possible value: None.
show status Syntax: show status Description: To display the status of STP. Argument: None. Possible value: None. Example: SNMP-GSH2416(stp)# show status STP Status : STP State Bridge ID Bridge Priority Designated Root Designated Priority Root Port Root Path Cost Current Max.
system set contact Syntax: set contact Description: To set the contact description of the switch. Argument: :string length up to 40 characters. Possible value: : A, b, c, d, ... ,z and 1, 2, 3, …. etc. Example: SNMP-GSH2416(system)# set contact Taipei set device-name Syntax: set device-name Description: To set the device name description of the switch. Argument: : string length up to 40 characters.
show Syntax: show Description: To display the basic information of the switch. Argument: None. Possible value: None. Example: SNMP-GSH2416(system)# show Model Name : SNMP-GSH2416 System Description : L2 Managed Switch Location : Contact : Device Name : SNMP-GSH2416 System Up Time : 0 Days 0 Hours 4 Mins 13 Secs Current Time : Fri Jan 27 13:20:47 2006 BIOS Version : v65535.65535 Firmware Version : v2.14 Hardware-Mechanical Version : v65535.65535-v65535.
tftp set server Syntax: set server Description: To set up the IP address of tftp server. Argument: : the IP address of tftp server Possible value: : tftp server ip Example: SNMP-GSH2416(tftp)# set server 192.168.3.111 show Syntax: show Description: To display the information of tftp server. Argument: None. Possible value: None. Example: SNMP-GSH2416(tftp)# show Tftp Server : 192.168.3.
time set daylightsaving Syntax: set daylightsaving
Description: To set up the daylight saving.Syntax: set ntp Description: To set up the current time via NTP server. Argument: : ntp server ip address or domain name : time zone (GMT), range: -12 to +13 Possible value: : -12,-11…,0,1…,13 Example: SNMP-GSH2416(time)# set ntp clock.via.net 8 Synchronizing...
trunk del trunk Syntax: del trunk Description: To delete the trunking port. Argument: : port range, syntax 1,5-7, available from 1 to 24 Possible value: : 1 to 24 Example: SNMP-GSH2416(trunk)# del trunk 1 set priority Syntax: set priority Description: To set up the LACP system priority. Argument: : available from 1 to 65535.
show aggtr-view Syntax: show aggtr-view Description: To display the aggregator list. Argument: None. Possible value: None. Example: SNMP-GSH2416(trunk)# show aggtr-view Aggregator 1) Method: None Member Ports: 1 Ready Ports:1 Aggregator 2) Method: LACP Member Ports: 2 Ready Ports: : : : show lacp-detail Syntax: show lacp-detail Description: To display the detailed information of the LACP trunk group.
Syntax: show lacp-priority Description: To display the value of LACP Priority. Argument: None. Possible value: None. Example: SNMP-GSH2416(trunk)# show lacp-priority LACP System Priority : 32768 show status Syntax: show status Description: To display the aggregator status and the settings of each port. Argument: None. Possible value: None.
vlan del port-group Syntax: del port-group Description: To delete the port-based vlan group. Argument: : which vlan group you want to delete. Possible value: : port-vlan name Example: SNMP-GSH2416(vlan)# del port-group VLAN-2 del tag-group Syntax: del tag-group Description: To delete the tag-based vlan group.
disable sym-vlan Syntax: disable sym-vlan Description: To drop frames from the non-member port. Argument: : which port(s) you want to set, syntax 1,5-7, available from 1 to 24 Possible value: : 1 to 24 Example: SNMP-GSH2416(vlan)# disable sym-vlan 5-10 enable drop-untag Syntax: enable drop-untag Description: To drop the untagged frames.
set mode Syntax: set mode [up-link] Description: To switch VLAN mode, including disable, port-based, tag-based, metro and doubletag modes.
set port-role Syntax: set port-role [vid] Description: To set egress rule: configure the port roles.
set tag-group Syntax: set tag-group <#> Description: To add or edit the tag-based vlan group. Argument: : vlan ID, range from 1 to 4094 : tag-vlan name : vlan group members, syntax 1,5-7, available from 1 to 24 <#>: sym/asym vlan setting.
show pvid Syntax: show pvid Description: To display pvid, ingress/egress rule. Argument: None. Possible value: None.
vs disable Syntax: disable Description: To disable the virtual stack. Argument: None. Possible value: None. Example: SNMP-GSH2416(vs)# disable enable Syntax: enable Description: To enable the virtual stack. Argument: None. Possible value: None. Example: SNMP-GSH2416(vs)# enable set gid Syntax: set gid Description: To set the group id.
set role Syntax: set role Description: To set role. Argument: : master: act as master, slave : act as slave Possible value: : master or slave Example: SNMP-GSH2416(vs)# set role master show Syntax: show Description: To display the configuration of the virtual stack. Argument: None. Possible value: None.
5. Maintenance 5-1. Resolving No Link Condition The possible causes for a no link LED status are as follows: z The attached device is not powered on z The cable may not be the correct type or is faulty z The installed building premise cable is faulty z The port may be faulty 5-2. Q&A 1. Computer A can connect to Computer B, but cannot connect to Computer C through the Managed Switch. 9 The network device of Computer C may fail to work. Please check the link/act status of Computer C on the LED indicator.
Appendix A Technical Specifications Features • • • • • • • • • • • • • • • • • • • • • • • • • 8 (10/100/1000Mbps) Gigabit Ethernet (TP) switching ports are compliant with IEEE802.3, 802.3u, 802.3z and 802.3ab. 16 Gigabit SFP fiber ports. Non-blocking store-and-forward shared-memory Web-Smart switched. Supports auto-negotiation for configuring speed, duplex mode. Supports 802.3x flow control for full-duplex ports. Supports collision-based and carrier-based backpressure for half-duplex ports.
Hardware Specifications Standard Compliance: IEEE802.3/802.3ab / 802.3z / 802.3u / 802.
Diagnostic LED: System LED : Per Port LED: 10/100/1000M TP Port 1 to 8 1000M SFP Fiber Port 9 to 24 Power Requirement : Power, CPU : LINK/ACT, SPEED : SFP(LINK/ACT) AC Line Voltage : 100∼240 V Frequency : 50∼60 Hz Consumption : 30W Ambient Temperature : 0° to 40°C : 5% to 90% Humidity Dimensions : 44(H) × 442(W) × 209(D) mm Comply with FCC Part 15 Class A & CE Mark Approval 238 AirLive SNMP-GSH2416 User’s Manual
Management Software Specifications System Configuration Management Agent Spanning Tree Algorithm VLAN Function Trunk Function IGMP Bandwidth Control Quality of Service (QoS) Port Security Internetworking Protocol Network Management Auto-negotiation support on 10/100/1000 BaseTX ports, Web browser or console interface can set transmission speed (10/100/1000Mbps) and operation mode (Full/Half duplex) on each port, enable/disable any port, set VLAN group, set Trunk Connection.
Appendix B Null Modem Cable Specifications The DB-9 cable is used for connecting a terminal or terminal emulator to the Managed Switch’s RS-232 port to access the command-line interface. The table below shows the pin assignments for the DB-9 cable.
