Integration Guide
Table Of Contents
- 1.1. Accessories
- 1.2. Required Connectors
- 2.1. Power Supply
- 2.2. Module Power States
- 3.1. RF Connections
- 3.2. Sub-6G Antennas and Cabling
- 3.3. Ground Connection
- 3.4. Interference and Sensitivity
- 3.5. Radiated Sensitivity Measurement
- 3.6. Supported Frequencies
- 3.7. Antenna Specification
- 4.1. Important Notice
- 4.2. Safety and Hazards
- 4.3. Important Compliance Information for the United States and Canada
AirPrime EM9190 Hardware Integration Guide
RF Specifications
41113915
Rev 0.6
Aug 17, 2022
16
Band
5
MHz
10
MHz
15
MHz
20
MHz
25
MHz
30
MHz
40
MHz
50
MHz
60
MHz
70
MHz
80
MHz
90
MHz
100
MHz
n7
5
Yes
Yes
Yes
Yes
n8
5
Yes
Yes
Yes
Yes
n12
5
Yes
6
Yes
6
Yes
6
n20
5
Yes
Yes
Yes
Yes
n25
5
Yes
Yes
Yes
Yes
n28
Yes
Yes
Yes
Yes
Yes
n38
5
Yes
n40
5
Yes
Yes Yes Yes Yes Yes
n41
Yes
Yes
Yes
Yes
Yes
Yes
6
Yes
Yes
4
Yes
n48
5
Yes
6
Yes
6
Yes
6
Yes
6, 7
Yes
6, 7
Yes
6, 7
Yes
6, 7
Yes
6, 7
n66
Yes
Yes
Yes
Yes
Yes
Yes
6
n71
Yes
Yes
Yes
Yes
n77
Yes Yes
Yes
Yes
6
Yes
Yes
6
Yes
Yes
4, 6
Yes
n78
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
4
Yes
n79
Yes
Yes
Yes
Yes
Yes
6
Yes
1.
Table contents are derived from 3GPP TS 38.521-1 v16.3.0, table 5.3.5-1.
2.
For FR1 Sub-6G bands, NR TDD Bands (n41/77/78/79), only SCS 30KHz is supported, and for other FDD bands, only
SCS 15KHz is supported.
3.
For FR2 mmWave bands, only 50MHz and 100MHz bandwidth is supported.
4.
This UE channel bandwidth is optional in Release 15.
5.
Band support is firmware and SKU dependent.
6.
Indicated bandwidths may be disabled by default due to carrier deployment requirements.
7.
Downlink only
3.7. Antenna Specification
This appendix describes recommended electrical performance criteria for Sub-6G, GNSS, and
mmWave antennas used with AirPrime embedded modules.
The performance specifications described in this section are valid while antennas are mounted in the
host device with antenna feed cables routed in their final application configuration.
Note: Antennas should be designed before the industrial design is finished to make sure that the best
antennas can be developed.
3.7.1. Recommended WWAN Antenna Specifications
Table 3-6 Antenna Requirements
1
Parameter Requirements Comments
Antenna System
(NR/LTE) External multi-band 4x4 MIMO
antenna system (Ant1/ Ant2/Ant3/Ant4)
2
(3G) External multi-band antenna system
with diversity (Ant1/Ant2)
If Ant2 or Ant3 includes GNSS, then it
must also satisfy requirements in Table 3-
7.
Operating Bands —
Ant1
All supporting Tx and Rx frequency
bands.
Operating Bands —
Ant2/3/4
All supporting Rx frequency bands, plus
GNSS frequency bands if Ant2 is used in
shared Diversity/MIMO/GNSS mode.
VSWR of Ant1 and
Ant2
< 2:1 (recommended)
< 3:1 (worst case)
On all bands including band edges
DRAFT