EBAC01GSK Installation Manual

482 01 2229 02 11/13/13
Specifications subject to change without notice.
EBAC01GSK
INSTALLATION INSTRUCTIONS
HORIZONTAL/DOWNFLOW CONVERSION GASKET KIT
FOR FAN COILS
NOTE: Read the entire instruction manual before starting the
installation.
SAFETY CONSIDERATIONS
Installing, starting up, and servicing air−conditioning
equipment can be hazardous due to system pressures,
electrical components, and equipment location (roofs,
elevated structures, etc.).
Only trained, qualified installers and service mechanics
should install, start−up, and service this equipment.
Untrained personnel can perform basic maintenance
functions such as cleaning coils. All other operations should
be performed by trained service personnel.
When working on the equipment, observe precautions in the
literature and on tags, stickers, and labels attached to the
equipment.
Follow all safety codes. Wear safety glasses and work
gloves. Keep quenching cloth and fire extinguisher nearby
when brazing. Use care in handling, rigging, and setting bulky
equipment.
Read these instructions thoroughly and follow all warnings or
cautions included in literature and attached to the unit.
Consult local building codes and National Electrical Code
(NEC) for special requirements. In Canada, refer to current
editions of the Canadian Electrical Code, CSA 22.1.
Recognize safety information. This is the safety−alert symbol
!
!
. When you see this symbol on the unit and in instructions
or manuals, be alert to the potential for personal
injury.Understand these signal words: DANGER, WARNING,
and CAUTION. These words are used with the safety−alert
symbol. DANGER identifies the most serious hazards which
will result in severe personal injury or death. WARNING
signifies hazards which could result in personal injury or
death. CAUTION is used to identify unsafe practices which
may result in minor personal injury or product and property
damage. NOTE is used to highlight suggestions which will
result in enhanced installation, reliability, or operation.
! WARNING
FIRE, EXPLOSION, ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal injury,
death and/or property damage.
The ability to properly perform maintenance on this
equipment requires certain knowledge, mechanical skills,
tools, and equipment. If you do not possess these, do not
attempt to perform any maintenance on this equipment.
! WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal injury
or death.
Before installing, modifying, or servicing system, main
electrical disconnect switch must be in the OFF position
and install a lockout tag. There may be more than one
electrical supply to the fan coil. Check accessories and
cooling unit for additional electrical supplies that must be
shut off during fan coil servicing. Lockout and tag switch
with a suitable warning label. Verify proper operation after
servicing.
! CAUTION
CUT HAZARD
Failure to follow this caution may result in personal injury.
Sheet metal parts may have sharp edges or burrs. Use
care and wear appropriate clothing, safety glasses and
gloves when handling parts and servicing fan coil.
INTRODUCTION
This instruction covers the installation of this gasket kit
on models FVM, FCM, FEM, FSM, FSU, EBP, EBX,
EBW, EBV, WAH, WAP, WAX fan coils. This kit is
required when converting the low leak/low sweat fan
coils and helps retain their performance after the
conversion.
DESCRIPTION AND USAGE
This gasket kit is used in conjunction with downflow conversion
kits, downflow base kit and in the conversion of slope coil units
to horizontal right airflow.
INSTALLATION
1. Cut gasket 1 and gasket 2 to length as follows:
a. For the 14.2” cabinet−325mm (12.75”)
b. For the 17.5” cabinet−410mm (16.12”)
c. For the 21” cabinet−499mm (19.62”)
d. For the 24.5” cabinet−use as is
2. Apply gasket 1 referring to Fig. 1. Center in the first
flange with slight overhang on both ends. Cover the
flange completely.
3. Apply gasket 2 referring to Fig. 1. Center on the
second flange with slight overhang on each end. Align
the notch with the flange notch.
This gasket will have slight overhang of the flange edges.