User's Manual
Table Of Contents
- 1.1 0BPurpose
- 1.4 1BReferenced Documentation
- 2.1 2BProST Frequency Ranges
- 2.2 3BProST-2 Frequency Ranges
- 2.3 4BArchitecture
- 2.4 5BModels
- 3.1 6BPackage Contents
- 3.2 7BMinimum PC Requirements
- 3.3 8BRequired Tools
- 3.4 9BRadio Site Planning
- 4.1 10BProST Physical Description
- 4.2 11BSDA-1 Physical Description
- 4.3 12BSDA-4S Type II and SDA-4S/VL Type II (Optional)
- 4.4 13BSDA-4SDC Type II (Optional DC power supply)
- 5.1 14BWall Mounting
- 5.2 15BPole-Mounting
- 5.3 16BMounting the SDA-4S
- 6.1 17BConnecting to IDU
- 6.2 18BConnecting to LAN Network
- 7.1 19BDC Power Source
- 7.2 20BConnecting the SDA-4SDC Type II (Optional DC adapter)
- 7.3 21BAC Power Source
- 8.1 22BHousing the Connectors
- 8.2 23BConnecting to the SDA-4SDC
- 9.1 24BPolyPhaser Wiring Diagram
- 9.2 25BLightning and Surge Protection Connection Scenarios
- 10.1 26BLED Status
- 12.1 27BTroubleshooting
- 12.2 28BGlossary of Terms
- 12.3 29BRevision History
- 12.4 30BContact Information
ProST Hardware Installation User Guide
Page 65 Commercial in Confidence UWB-D00111 Rev K
10.1 LED Status
The RED Power LED functions as follows:
Table 15 - LED Status
Status Description
ON
ProST receiving power from SDA
OFF
No power being received
Blinking
Data transmission via Ethernet LAN
The LED status for each RSSI level is defined in the following table:
Table 16 - LED Status per RSSI level
RSSI Level dB LED 0 LED 1 LED 2 LED 3 LED 4 LED 5 LED 6 LED 7
97dB-
0 0 0 0 0 0 0 0
93 - 96
1 0 0 0 0 0 0 0
89 - 92
1 1 0 0 0 0 0 0
83 - 88
1 1 1 0 0 0 0 0
79 - 82
1 1 1 1 0 0 0 0
75 - 78
1 1 1 1 1 0 0 0
71 - 74
1 1 1 1 1 1 0 0
67 - 70
1 1 1 1 1 1 1 0
66 dB+
1 1 1 1 1 1 1 1
Before connecting the power adapter to the ProST, you need to connect the AC power cable (that
connects to the subscriber’s power outlet) to the adapter, as described in the following procedure.
To connect the RSSI LED Plug Adapter:
1. Connect the 15-pin D-type male connector, at one end of the straight-through cable, to the
ProST.
2. Connect the 15-pin D-type female connector, at the other end of the straight-through cable
from the ProST, to the RSSI LED adapter.
3. Connect the 15-pin D-type male connector, at one end of the straight-through cable, to the
SDA.
4. Connect the 15-pin D-type male connector, at the other end of the straight-through cable
from the SDA, to the RSSI LED adapter.
Note: You can connect the RSSI LED Plug adapter's 15-pin male port
directly to the ProSt's 15-pin female port, instead of using a cable.