User Manual
Table Of Contents
- 1.1 0BPurpose
- 1.4 1BReferenced Documentation
- 2.1 2BProST Frequency Ranges
- 2.2 3BProST-2 Frequency Ranges
- 2.3 4BArchitecture
- 2.4 5BModels
- 3.1 6BPackage Contents
- 3.2 7BMinimum PC Requirements
- 3.3 8BRequired Tools
- 3.4 9BRadio Site Planning
- 4.1 10BProST Physical Description
- 4.2 11BSDA-1 Physical Description
- 4.3 12BSDA-4S Type II and SDA-4S/VL Type II (Optional)
- 4.4 13BSDA-4SDC Type II (Optional DC power supply)
- 5.1 14BWall Mounting
- 5.2 15BPole-Mounting
- 5.3 16BMounting the SDA-4S
- 6.1 17BConnecting to IDU
- 6.2 18BConnecting to LAN Network
- 7.1 19BDC Power Source
- 7.2 20BConnecting the SDA-4SDC Type II (Optional DC adapter)
- 7.3 21BAC Power Source
- 8.1 22BHousing the Connectors
- 8.2 23BConnecting to the SDA-4SDC
- 9.1 24BPolyPhaser Wiring Diagram
- 9.2 25BLightning and Surge Protection Connection Scenarios
- 10.1 26BLED Status
- 12.1 27BTroubleshooting
- 12.2 28BGlossary of Terms
- 12.3 29BRevision History
- 12.4 30BContact Information
ProST Hardware Installation User Guide
Page 24 Commercial in Confidence UWB-D00111 Rev K
3 Installation Prerequisites
Before installing your ProST, read the following to ensure that:
¾
1No items are missing from the package
¾
1Minimum computer requirements are fulfilled
¾
1You have the required installation tools
¾
1Radio Site planning has been performed
3.1 Package Contents
Examine the ProST shipping container. If you notice any damage, or missing items as listed in the
Packing List, immediately notify the carrier that delivered the unit and contact a Airspan
representative.
The ProST kit should contain the following items:
¾ ProST
¾ DB15-to-RJ45 adapter for plugging into the ProST's 15-pin D-type port (with pins 7 & 8
not connected), replaces previous adapter.
¾ Wall-mounting kit:
• Mounting bracket
• 2 x M10 x 1.5 hex head screws - 20mm length
• 2 x M10 hex nuts
• 2 x M10 plain washers
• 2 x M10 spring lock washers
Note: The standard ProST kit does not include pole-mounting accessories.
For pricing and ordering of pole-mounting accessories, please contact your
nearest Airspan dealer.
Note: The standard ProST kit does not include the SDA-1 Type II adapter.
For pricing and ordering of the SDA-1 Type II adapter, please contact your
nearest Airspan dealer.
3.2 Minimum PC Requirements
Ensure that your computer provides an Ethernet interface such as a Network Interface Card (that
provides an RJ-45 port).
Caution: Only subscriber terminal equipment (e.g. computer modem port)
that is designed for full compliance with TNV-1 telecommunication network
can be connected to the SDA-1. Warranty of Airspan's equipment shall be
made void if the SDA-1 is connected to a computer that is not compliant with
TNV-1.
3.3 Required Tools
The following tools are required to install the ProST unit:
¾ Crimping tool for crimping CAT-5e cables to RJ-45 connectors.
¾ Cable stripping tool