The Innovation Behind Broadband Wireless IP-based Broadband Wireless Access (BWA) System 605-0000-706 Rev E ProST Hardware Installation Guide Connecting the World
Intentionaly left blank
Table Of Contents Introduction ....................................................................................................................... 1 Purpose .......................................................................................................................... 1 Targeted Audience ........................................................................................................... 1 Referenced Documentation .........................................................................
605-0000-706 ProST Installation User Guide-Rev E Ports ......................................................................................................................... 17 LED ........................................................................................................................... 17 SDA-4S Type II and SDA-4S/VL Type II (Optional).............................................................. 18 Physical Dimensions....................................................................
Table Of Contents 1.3 Important Service Information.................................................................................... 64 1.4 UL Information ......................................................................................................... 64 1.5 CE Notice ................................................................................................................ 64 1.6 European Community, Switzerland, Norway, Iceland, and Liechtenstein ............................
INTRODUCTION Thank you for purchasing Airspan's ProST wireless access device. The ProST customer premise equipment (CPE) is part of Airspan's AS.MAX family of WiMAX-based products. This section provides a preface by discussing the purpose, audience, organization, conventions, and customer support of this guide. Purpose This guide provides step-by-step instructions for setting up and installing the ProST.
605-0000-706 ProST Installation User Guide-Rev E WARNINGS AND CAUTIONS Human Exposure to Radio Frequencies The ProST should be installed and operated from a minimum distance of 20 cm to your body. Radio Interference This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Introduction The information in this document is subject to change without notice and does not represent a commitment on the part of the vendor. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular purpose of this document.
605-0000-706 ProST Installation User Guide-Rev E DECLARATION OF CONFORMITY European Community, Switzerland, Norway, Iceland, and Liechtenstein Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Deutsch: Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprecheneden Vorgaben der Richtlinie 1999/5/EU.
Introduction Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i Direktiv 1999/5/EC. The Declaration of Conformity related to this product can be obtained from product_management@Airspan.
SYSTEM OVERVIEW The ProST is an outdoor WiMAX-based customer premises equipment (CPE). The ProST, which uses Intel Corporation’s Pro/Wireless 5116 broadband interface, connects IP-enabled devices directly to WiMAX networks. Designed for the residential and small enterprise (SME) markets, the device supports high-speed broadband Internet through a Fast Ethernet connection. The ProST ensures high service availability at enhanced ranges, operating in both LOS and NLOS propagation environments.
System Overview ProST Frequency Ranges The table below lists the frequency range of ProST models currently available. This table will grow as more models become available. Frequency Band Channel Bandwidth 3.3 – 3.5 GHz in TDD mode 3.4 – 3.6 GHz in FDD mode 4.9 – 5.0 GHz in TDD mode 5.725 – 5.825 GHz in TDD mode Channel Throughput 1.75 MHz speeds of up to 6.5 Mbps 3.5 MHz speeds of up to 13.1 Mbps 5 MHz speeds of up to 18 Mbps 1.75 MHz speeds of up to 6.5 Mbps 3.5 MHz speeds of up to 13.
605-0000-706 ProST Installation User Guide-Rev E Note: The SDA-1 Type II adapter can also be implemented with other Airspan's ASWipLL radios (i.e. BSR, PPR, and SPR). For further information regarding these products, please contact your nearest Airspan dealer. The figure below displays a typical architecture setup of the ProST with an integrated antenna.
System Overview The ProST model with the N-type connector for connecting an external antenna is shown below: ProST Block Diagram The figure below displays a block diagram of the ProST: 9
605-0000-706 ProST Installation User Guide-Rev E ProST Protocol Stack The figure below displays a block diagram of the ProST's network architecture, designed as a hierarchy of protocols (i.e. protocol stack) implemented in the communication network. Theory of Operation For basic operation, the ProST requires no initial configuration--simply plug and play. Configuration is automatically performed over the air by the BS.
INSTALLATION PREREQUISITES Before installing your ProST, read the following to ensure that: No items are missing from the package Minimum computer requirements are fulfilled You have the required installation tools Radio Site planning has been performed Package Contents Examine the ProST shipping container. If you notice any damage, or missing items as listed in the Packing List, immediately notify the carrier that delivered the unit and contact a Airspan representative.
605-0000-706 ProST Installation User Guide-Rev E o Philips head screwdriver o Flat-blade screwdriver o A/F open ended spanner Crimping tool for crimping RF cable to N-type connector (only relevant when implementing external antenna) Torque wrench for N-type connectors (only relevant when implementing external antenna) Note: Airspan does not provide screws and wall anchors for mounting the ProST to the wall. The screw size depends on the structure of the building to which the ProST is to be attached.
Installation Prerequisites Fresnel Zones define the amount of clearance required from obstacles. These zones are composed of concentric ellipsoid areas surrounding the straight-line path between two antennas. Thus, the zone affects objects to the side of the path and those directly in the path.
605-0000-706 ProST Installation User Guide-Rev E achieved, and then secure the ProST. For viewing RSS values, see "Web-based Management" for standard alignment, for finer alignment, see RSSI LED Plug Adapter.
PHYSICAL DESCRIPTION This section provides a description of the components of the ProST installation: ProST radio (outdoor unit) SDA-1 adapter (indoor unit -- switch and power interface) SDA-4S Type II and SDA-4S/VL Type II adapters (optional) ProST Physical Description The ProST is an encased outdoor radio providing access to communication ports on its bottom panel. The ProST's back panel provides holes for ProST mounting.
605-0000-706 ProST Installation User Guide-Rev E SDA-1 Physical Description The SDA-1 is an integrated Ethernet and AC/DC power supply adapter that simply plugs into a standard electrical wall outlet (110/240 VAC). The SDA-1 enables easy plug prong replacement to suit geographical location of electrical outlet sockets (e.g. American vs. European).
Physical Description This section provides the following SDA-1 physical descriptions: Dimensions Ports LED Physical Dimensions The SDA-1 physical dimensions are described in the table below: Parameter Value Dimensions (L x W x H) 72 x 42.5 x 26 mm (2.83 x 1.67 x 1.02 inches) Weight 0.
605-0000-706 ProST Installation User Guide-Rev E SDA-4S Type II and SDA-4S/VL Type II (Optional) The SDA-4S Type II and SDA-4S/VL Type II indoor units (hereafter referred to as SDA-4S for convenience) are two optional integrated LAN switches that offer an alternative to the SDA-1 Type II unit. These two units have identical physical dimensions and design, as displayed in the figure below.
Physical Description Ports The SDA-4S Type II and SDA-4S/VL Type II adapters provide ports on their bottom panels, which are described in the table below: Port Interface 4 x 8-pin RJ-45 10/100BaseT with subscriber's network (supports Auto Negotiation and MDI/MDI-X automatic crossover, allowing connection of straight-through or crossover cables) 15-pin D-type (female) 10/100BaseT with ProST AC power socket Subscriber's power outlet (110/240 VAC, 50/60 Hz) Note: The ports of the SDA-4S models support
605-0000-706 ProST Installation User Guide-Rev E LEDs The SDA-4S Type II and SDA-4S/VL Type II adapters (referred conveniently as SDA-4S) provide LED indicators on their top panels, which are described in the table below: LED Color Status Meaning UPLINK Yellow (100BaseT) or Orange (10BaseT) On Physical link (10BaseT or 100BaseT) between SDA-4S adapter and ProST Blinking Traffic currently flowing between SDA4S and ProST Off No link between SDA4S and ProST On Physical link (10BaseT or 100BaseT)
Physical Description The figure below displays the LEDs which are located on the top panel of the SDA-4S Type II and SDA-4S/VL Type II adapters: 21
MOUNTING THE PROST This section describes the mounting procedures for the ProST and the optional SDA-4S adapters. Mounting the ProST Warning: ProST is an outdoor radio unit and therefore, must only be mounted outdoors. Warning: Mount the ProST in an orientation such that its 15-pin D-type port (located on the bottom panel) faces downwards. This prevents rain water from settling on the port, and thereby, avoiding damage to the unit such as corrosion and electrical short-circuiting.
Mounting the ProST Wall Mounting The ProST is wall mounted in two main stages: Attaching the mounting bracket to the ProST's mounting holes Attaching the mounting bracket (attached to the ProST ) to the wall To wall mount the ProST: 1. Position the unassembled mounting bracket on the mounting surface (e.g. wall), and then use a pencil to mark the position of the four mounting holes.
605-0000-706 ProST Installation User Guide-Rev E 3. Insert wall anchors (not supplied) into each of the drilled holes. 4. Align the mounting bracket's four holes with the wall anchors, and then insert a screw (not supplied) through the mounting bracket holes into each wall anchor, and tighten. Note: Airspan does not provide screws for attaching the mounting bracket to the wall. The screw size depends on the structure of the building to which the bracket is to be attached.
Mounting the ProST 6. Adjust the horizontal positioning of the ProST, and then tighten the two M10-hex head screws with the M10 hex nuts. Note: A third-party thread-locking compound must be applied to the M10-hex head screws to prevent the bolts from working loose. Rotation is restricted in the horizontal plane only, as shown in the figure below: Pole Mounting Pole mounting allows the ProST to be easily adjusted in the horizontal (azimuth) and vertical (elevation) planes for antenna alignment.
605-0000-706 ProST Installation User Guide-Rev E on the ProST's back panel and the supplied (when ordered) pole-mounting brackets. The polemounting bracket is designed to support the ProST on a round pole of 45 mm in diameter. The figure below illustrates a summary of the ProST pole-mounting procedure. To pole mount the ProST: 26 1. Attach the mounting bracket to the ProST: a.
Mounting the ProST 2. Attach the clamping bracket to the mounting bracket: a. Slide an M6-spring lock washer onto an M6-hex head screw. Align the mounting bracket's and clamping bracket's pivot holes, such that the clamping bracket is aligned to the inside of the mounting bracket. From the external side of the mounting bracket, insert the M6-hex head screw into the pivot holes and then fasten, but not tightly. (The clamping bracket provides a built-in nut.) b.
605-0000-706 ProST Installation User Guide-Rev E 28 3. Attach the U-bolt to the pole: a. Place one U-bolt around the pole, and then insert the U-bolt screw side through the two corresponding holes (horizontally parallel) on the clamping bracket. Slide an M8-flat washer and M8-spring lock washer onto each U-bolt screw side (ensure that the flat washer is adjacent to the clamping bracket). Fasten each U-bolt side with the two M8-hex nuts. b. Attach the second U-bolt as described above. 4.
Mounting the ProST b. Adjust the horizontal position of the ProST by rotating it about the pole, and then tightening the nuts of the U-bolts. Note: A thread-locking compound must be used to prevent the bolts from working loose. ProST positioning is obtained in two planes by adjustment of the mounting bracket assembly as shown below: Note: It is important to provide strain relief and drip loop for Cat-5 cables.
605-0000-706 ProST Installation User Guide-Rev E SDA-4S The SDA-4S adapters can be mounted either horizontally on a desktop or vertically on a wall. Desktop Mounting Desktop mounting is made possible by the existence of four feet, each located on the four corners of the SDA-4S bottom panel. Therefore, no installation is necessary for desktop mounting. Warning: To prevent a fire hazard caused by overheating, do not place the SDA-4S on a carpeted surface where airflow is restricted.
Mounting the ProST 2. Drill holes for each hole that you marked in the step above. 3. Insert wall anchors (supplied) into each of the drilled holes. 4. Insert the 9-inch screws (supplied) into the wall anchors. Ensure at least 2 mm of the screw is exposed to allow insertion into the SDA-4S mounting holes. 5. Hold the SDA-4S with both hands, and align the entrance to the two mounting hooks with the screws. Slide the screws into the mounting hooks, by lowering the SDA-4S onto the screws.
NETWORK CABLING ProST interfaces with the subscriber's network through the IDU (i.e. typically the SDA-1 Type II, or optionally through the SDA-4S Type II or SDA-4S/VL Type II). The ProST also receives DC power from the IDU. This section describes the ProST network cabling: Connecting ProST to IDU Connecting IDU to a Computer Connecting to IDU The ProST typically interfaces with the subscribers network using the indoor SDA-1 Type II adapter.
Network Cabling However, if you implement your company's wire color-coding scheme, ensure that the wires are paired and twisted according to pin functions listed in the table above (e.g. Rx+ with Rx). • The maximum CAT 5 cable length for ODU/IDU connectivity is 100 meters. To connect the ProST to the SDA-1: 1. Attach the DB15 side of the DB15-to-RJ45 adapter to the ProST's 15-pin D-type port (female), labeled DATA & PWR. 2.
605-0000-706 ProST Installation User Guide-Rev E Cable: Straight-through CAT 5 Ethernet cable Connectors: o ProST: DB15-to-RJ45 adapter o SDA-4S: DB15-to-RJ45 adapter o CAT 5 cable with 8-pin RJ-45 male connectors on either end Connector pinouts: Note: The standard ProST kit does not include the SDA-4S Type II or SDA-4S/VL Type II adapters. For pricing and ordering of either the SDA-4S Type II or SDA-4S/VL Type II adapter, please contact your nearest Airspan dealer.
Network Cabling Note: • Only pins 1 to 6 are used. • Pins 7 and 8 must not be wired to the ProST end. • The wire color-coding described in the table is Airspan's standard for wire color-coding. However, if you implement your company's wire color-coding scheme, ensure that the wires are paired and twisted according to pin functions listed in the table above (e.g. Rx+ with Rx). • The maximum CAT 5 cable length for ODU/IDU connectivity is 100 meters.
605-0000-706 ProST Installation User Guide-Rev E Warning: Only subscriber terminal equipment (e.g. computer modem port) that is designed for full compliance with TNV-1 telecommunication network connectivity can be connected to the SDA-1. Warranty of Airspan's equipment shall be made void if the SDA-1 is connected to a computer that is not compliant with TNV-1. Using SDA-1 Type II The SDA-1 Type II provides a single 100BaseT interface with the subscriber's LAN network.
Network Cabling Using the SDA-4S Type II or SDA-4S/VL Type II The SDA-4S Type II or SDA-4S/VL Type II adapters (referred hereafter as SDA-4S) provide one four RJ-45 (100BaseT) ports for interfacing with the subscriber's LAN network. The difference between these two adapters is that the SDA-4S/VL supports VLAN functionality at the ports.
605-0000-706 ProST Installation User Guide-Rev E Cable: Straight-through (e.g. when connecting to PC) or crossover (i.e. when connecting to a hub) CAT 5 Ethernet cable Connectors: 8-pin RJ-45 at both ends Connector pinouts: o Straight-through cable (e.g. connecting to a PC) Pin Function 1 Tx+ 2 Tx- 3 Rx+ 6 Rx- o 8-Pin RJ-45 Crossover cable (e.g.
Network Cabling 39
CONNECTING TO POWER The ProST is powered from an outdoor AC/DC power adapter that is connected to a 110/240 VAC power source. ProST is a DC-powered device requiring 48 VDC at 24W max. (assuming up to 100-m cable length between ProST and AC/DC power adapter). Additionally the ProSt can be powered by the SDA-1 Type II, SDA-4S Type II or the SDA-4S/VL, optional internal integrated LAN switches. The outdoor AC/DC power adapter connects to the ProST through the ProST's 15-pin D-type port.
Connecting to Power 2. Prepare the AC power cord (that will connect to the subscriber's power outlet) for connection to the power adapter by performing the following: a. Strip about 25.4 mm (1 inch) of the outer jacket of the AC power cord to expose the three insulated wires. b. Using a wire-stripping tool, expose about 6.3 mm (0.25 inch) of each of the three wires (i.e. live, neutral, and ground) by striping the wires' insulation.
605-0000-706 ProST Installation User Guide-Rev E 42 7. Replace the cover by using the four screws, ensuring that the gasket (for weatherproofing) is firmly in place on the rim of the cover. 8. Locate the power adapter's 15-pin D-type connector located at the end of the pre-installed cable, and plug it into the ProST's 15-pin D-type port labeled DATA&PWR.
Connecting to Power Mounting AC/DC Power Adapter The AC/DC power adapter is mounted outdoors, together with the ProST. The maximum separation distance between the power adapter and the ProST is 60 cm (according to the cable length connecting these units). The power adapter provides four mounting brackets for mounting the power adapter.
605-0000-706 ProST Installation User Guide-Rev E To mount the AC/DC power adapter: 44 1. Attach the four mounting brackets to each rear corner of the power adapter using the four 10-mm Phillips screws (supplied), as illustrated in the figure below. Ensure the following: a. The notch located in the center (and on one side) of each bracket is inserted firmly into the holes on the power adapter. b.
Connecting to Power 3. Drill holes for accepting 30-mm length with 3-mm diameter screws and wall anchors. 4. Tap the wall anchors into the drilled holes. 5. Align the power adapter's mounting brackets with the drilled holes, and then secure it to the mounting surface using the 20-mm Philips screws. Note: It is important to provide strain relief and drip loop for the power cables. This can be done using cable ties to tie the cables to the pole as displayed in the Mounting section.
605-0000-706 ProST Installation User Guide-Rev E In addition, Airspan offers an optional third-party outdoor, lightning and surge protector that protects the ODU-to-IDU CAT 5 cable's power and data signals from any electrical surges due to lighting strikes. Note: ProST is designed with a built-in lightning surge protection that complies with the Surge Immunity standard EN 61000-4-5. DC Power Source ProST can be connected directly to a DC power supply unit that supplies 10 – 52 VDC (0.2 to 0.
Connecting to Power AC Power Source ProST is powered from an AC power source when implementing the SDA-1 Type II, which is plugged directly into a standard electrical wall outlet (110/240 VAC). The optional IDU adapters (SDA-4S Type II and SDA-4S/VL Type II) also power ProST from the subscriber's AC electrical wall outlet. The difference between the SDA-1 Type II and SDA-4S adapters is the method of connectivity to the power outlet, as discussed in the subsections below.
605-0000-706 ProST Installation User Guide-Rev E Changing the SDA-1 Type II Plug Prongs The SDA-1 Type II allows you to attach plug prongs suited to the electrical wall socket of the country in which you are installing the equipment. Therefore, before plugging the SDA-1 Type II into the electrical outlet, ensure that the correct prongs are attached to the SDA-1 Type II. To change the SDA-1 Type II plug prongs: 1. On the rear of the SDA-1 Type II, slide the locking switch to OPEN. 2.
Connecting to Power Verify that your SDA-1 Type II is on and receiving power by checking that the LED labeled POWER is lit (see SDA-1 Type II LED description). If it is not lit, see Troubleshooting. Using SDA-4S Type II and SDA-4S/VL Type II The SDA-4S adapters are plugged into a standard electrical wall outlet (110/240 VAC) using an AC power cord.
605-0000-706 ProST Installation User Guide-Rev E 1. Connect the power plug female, at the end of the AC power chord, into the AC power socket located on the left panel of the SDA-4S. 2. Plug the power plug male, at the other end of the AC power chord, into the AC power outlet (110-240 VAC). 3. Verify that the power is received by the SDA-4S by checking that the POWER LED light is on.
Connecting to Power Deployment of ProST in geographical areas that frequently experience severe lightning storms The lightning and surge protector protects the ODU-to-IDU CAT 5 cable's six used wires (two -48 VDC wires and four Ethernet Tx and Rx wires) from any electrical surges due to lighting strikes. The protector is installed outdoors on the CAT 5 cable that connects between the ProST and the IDU (i.e. SDA-1 Type II or SDA-4S).
605-0000-706 ProST Installation User Guide-Rev E mounting holes). The unit may be mounted/grounded on a nearby plate or bulkhead panel that is bonded to an earth-ground system. 6. Attach the protector's lid by using the four M4 x 20-mm screws. Ensure that the neoprene gasket on the lid is not loose or out of the groove. 7. Secure the CAT 5 cable to the grommet by fastening the gland nut.
Connecting to Power 53
RSSI LED PLUG ADAPTER Antenna Alignment using RSSI LED Plug Adapter The RSSI LED Plug is a small adapter that allows you to accurately position (align) the ProST for optimal radio frequency signal reception with the Base Station. The RSSI LED Plug adapter provides LEDs that indicate the ProST's received signal strength (RSS) with the Base Station.
RSSI LED Plug Adapter LED Status The RED Power LED functions as follows: Status Description ON ProST receiving power from SDA OFF No power being received Blinking Data transmission via Ethernet LAN The LED status for each RSSI level is defined in the following table: RSSI Level dB LED 0 LED 1 LED 2 LED 3 LED 4 LED 5 LED 6 LED 7 97dB- 0 0 0 0 0 0 0 0 93 96 1 0 0 0 0 0 0 0 89 92 1 1 0 0 0 0 0 0 83 88 1 1 1 0 0 0 0 0 79 82 1 1 1 1 0 0 0 0 75 78 1
605-0000-706 ProST Installation User Guide-Rev E Note: You can connect the RSSI LED Plug adapter's 15-pin male port directly to the ProSt's 15-pin female port, instead of using a cable.
CONNECTING EXTERNAL ANTENNA The ProST model without a built-in antenna provides an N-type port for connecting a third-party external antenna. The addition of an external antenna allows greater RF sector coverage than the standard ProST built-in antenna model. The external antenna is typically implemented in scenarios where the ProST is deployed at relatively far distances from the base station. Warning: Before connecting the external antenna, ensure that the ProST is not connected to the power source.
605-0000-706 ProST Installation User Guide-Rev E 58
TROUBLESHOOTING The table below provides some possible solutions to problems that may arise if the ProST is incorrectly installed: Problem Possible Cause Solution SDA-1 (and therefore, ProST) not receiving power --POWER LED is off No electricity at wall outlet Ensure household provides electricity to the specific wall outlet (professional electrician required) SDA-1 prongs not plugged entirely into wall outlet socket Ensure SDA-1 plug prongs are completely inserted into wall outlet SDA-1 plug prong
TRADEMARKS AND COPYRIGHTS 1. © Airspan Networks Inc 2006 2. The information in this document is proprietary to Airspan Networks Inc. This document may not in whole or in part be copied, reproduced, or reduced to any medium without prior consent, in writing, from Airspan Networks Incorporated. 3. This manual is subject to revision. 4. All rights reserved. 5. Right of modification reserved. 6. This manual is supplied without liability for errors or omissions. 7.
CONTACT INFORMATION UK Office for sales and general enquiries Airspan Communications Ltd Cambridge House Oxford Road Uxbridge Middlesex UB8 1UN Call +44 (0) 1895 467100 Fax +44 (0) 1895 467101 email sales@ airspan.com Internet: Airspan.com Customer Service Help-Desk for customer service emergency Airspan Communications Limited Cambridge House Oxford Road Uxbridge Middlesex UB8 1UN Int. Tel: +44 (0) 1895 467 467 Int. Fax: +44 (0) 1895 467 472 E-mail: Support@Airspan.
REVISIONS Revision Level Date Main Changes A 24-11-2005 Initial Document B 28-3-2006 Warning Removed Additions C 23-4-2006 RSSI LED Plug D 20-06-2006 Standardize document + additions E 17-06-2006 Corrections 62
WARNINGS 1. Disclaimer Every effort has been made to ensure the accuracy of the material provided herein; however, Airspan assumes no responsibility regarding the use of the material. Additionally, Airspan makes no representations or warranties, either expressed or implied, regarding the contents of this product. Airspan Networks Inc. shall not be liable for any misuse regarding this product.
605-0000-706 ProST Installation User Guide-Rev E Electro-Magnetic Radiation High Voltage 1.3 Important Service Information 1. Refer all repairs to qualified service personnel. Do not remove the covers or modify any part of this device, as this will void the warranty. 2. Disconnect the power to this product and return it for service if the following conditions apply: 3. a. The terminal does not function after following the operating instructions outlined in this manual. b.
Warnings and Cautions By the very nature of the system design and installation users will not find them selves within close proximity of the subscriber terminals. Standards EN50383 and EN50385 are the applicable harmonised standards for EM fields generated by fixed wireless equipment. The Electromagnetic fields generated by the Central Terminal antenna are below the recommended safe levels at all distances greater than 65 cm from an approved Airspan antenna.
605-0000-706 ProST Installation User Guide-Rev E Este equipamento satisfaz os requisitos essenciais e outras provisões da Directiva 1999/5/EC. Suomalainen: Tämä laite täyttää direktiivin 1999/5/EY oleelliset vaatimukset ja on siinä asetettujen muidenkin ehtojen mukainen. Svenska: Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i Direktiv 1999/5/EC. The Declaration of Conformity related to this product can be obtained from product_management@Airspan.
Warnings and Cautions - Install one RF lightning protector between the radio and antenna in series with the RF cable. - A lightning arrestor in series with the RF cable at the point of entry to the building. - Install a lightning arrestor in series with the IF cable at the transceiver on the tower/mast. - The AC wall outlet ground for the MacroMAX terminal must be connected to the same grounding system as the radio and antenna lightning protectors.
GLOSSARY B BPSK: Binary Phase Shift Keying BS: Base Station BWA: Broadband Wireless Access C CID: Connection Identifier Number CPE: Customer Premises Equipment (interchangeable with ST) D dB: Decibel dBm: Power ratio in dB (decibel) of the measured power referenced to one milliwatt DL: Downlink F FDD: Frequency Division Duplex FEC: Forward Error Correction FTP: File Transfer Protocol G GHz: Gigahertz.
Glossary MAC: Media Access Controller. The next layer up from the PHY. Mbit/s: Megabits per second MHz: Megahertz (one million cycles per second) MIB: Management Infomation Base N NLOS: Non Line-of-Sight radio propagation path O ODU: Outdoor Unit (i.e.
605-0000-706 ProST Installation User Guide-Rev E V VoIP: Voice over Internet Protocol W WiMAX: WiMAX is a wireless industry coalition whose members are organized to advance IEEE 802.16 standards for broadband wireless access (BWA) networks.
INDEX A P Antenna Alignments Pole Mounting ....................................... 23 Orientating when Pole Mounted ............. 23 Ports Orientating when Wal Mounted) ............ 23 ProST Port Description ......................... 16 Architecture ............................................ 6 SDA-1 Port Descriptions ....................... 16 Power B Bandwidth Speed..................................... 6 Changing SDA-1 Plug Prongs ................ 41 Benefits..................................
How to find out more about Airspan products and solutions For more information about Airspan, its products and solutions, please visit our Web site: www.airspan.com Or write to us at one of the addresses below. Airspan has offices in the following countries: Europe Czech Republic Poland Russia We will be delighted to send you additional United Kingdom information on any of our products and their Africa applications around the world.
